light industry. SUBSTANCE: material designed for finishing fancy goods, baby carriages, furniture, and also for finishing building interiors, etc. contains textile warp and polymer layer. The former has surface density 100 to 320 g/sq.m and consists of flax fibers or following mixtures of fibers: flax, cotton, and viscose at ratio (10- 50):(35-20):(55-30); flax, viscose, and polyester, (10-50):(50...

light industry. SUBSTANCE: material designed for finishing fancy goods, baby carriages, furniture, and also for finishing building interiors, etc. contains textile warp with surface density 100 to 320 g/sq.m, which consists of flax fibers or following mixtures of fibers: flax, cotton, and viscose at ratio (10-50): (35-20): (55-30); flax, viscose, and polyester, (10-50): (50-30): (40-20); flax and ...

measurement technology. SUBSTANCE: device may be used in telemetry with varying resistance of telecommunication. The device has current pulse source, single-conductor cable, stabilizer diode, heat-stable resistor and temperature sensor. The latter is used in the form of microcircuit temperature sensor, and current pulse source is made in the form of shaper of two alternating unipolar current pulse...

gas-producing industry. SUBSTANCE: device may be used for measurement of flow rate of gas and quantity of sand in production of operating gas wells. Introduced into device is sand measuring channel to extend functional potentialities of device in its use on gas wells. Introduced into measuring channel of gas flow rate is controlled scaler whose optimal amplification factor is set by microprocessor...

gas-producing industry. SUBSTANCE: device may be used for simultaneous separate measurement of gas flow rate and quantity of sand and water-clay-sand mixture in production of operating gas wells. Introduced into device are two information channels for measurement of quantities of sand and water-clay-sand mixture to extend device functional potentialities in its use on gas wells. Introduced into me...

gas-producing industry. SUBSTANCE: device may be used for simultaneous separate measurement of flow rate of gas and quantities of sand and water-clay-sand mixture in production of operating gas wells. Introduced into device are two information channels for measurement of quantities of sand and water-clay-sand to extend functional potentialities of device in use on gas wells. Introduction of contro...

oil field equipment. SUBSTANCE: device may be used for integral sampling of multicomponent gas-liquid systems transported by pipelines. The sampling device has body, sampling chamber with intake holes, shutoff member with control handle and guide tube. Sampling chamber is installed in body on rotation supports and in off-position it is located beyond the space designed for motion of process flow. ...

lighting engineering. SUBSTANCE: glow-discharge lamp emitting light in ultraviolet wavelength range has its working medium composed of iodine vapors and buffer gas such as xenon or helium, or their mixture. EFFECT: improved operating efficiency of lamp. 1 tbl

Splicing is carried out in a humid environment. A method for splicing yarns using a flow of air, in order to form a high tensile strength yarn, comprises carrying out the splicing in a humid environment. An Independent claim is also included for the splicing device, comprising a splicing chamber with an air supply and means for creating a humid environment.

PROBLEM TO BE SOLVED: To obtain a rotational speed difference between right/left running drive wheels in proportion to a turning radius at turning time simultaneously with driving a plurality of the running drive wheels, so as to improve running performance on a bad road and the weak ground, by arranging a plurality of sets of pair of the right/ left running drive wheels in a longitudinal directio...

PROBLEM TO BE SOLVED: To realize miniaturization of an electric motor and a generator in an electric motor drive force assisting vehicle. SOLUTION: When a slip of a front wheel is judged in a rear wheel assist control judging circuit 13c, an alternator 6 is connected to a motor side from a battery side by switching a changeover switch 8, and motor power and an engine speed are calculated by a rear...

PROBLEM TO BE SOLVED: To set a release condition of each system so as to prevent both forward/backward and side control from being simultaneously given to a driver, by providing an operation integrated control means performing control in such a manner that a lane keep system can be operated only in the case that an inter-vehicle control type constant speed running system is in operation. SOLUTION:...

PROBLEM TO BE SOLVED: To freely execute the gear shifting operation of a mechanical reduction gear by regulating the rotating speed of a prime motor to the rotating speed of an axle corresponding to the traveling speed of a motor vehicle, considering the change gear ratio by a gear, and synchronizing a pair of gears. SOLUTION: When a driver holds and moves an operation lever in an intended directi...

PROBLEM TO BE SOLVED: To change the driving force according to road surface gradient by controlling at least one of an engine and an automatic transmission so as to realize a corrected target driving force obtained by correcting a general target driving force with a weight gradient resistance force. SOLUTION: A PCM 111 comprises a general target driving force setting part 161, a weight gradient re...

PROBLEM TO BE SOLVED: To simplify the system configuration by embodying on the electric command system and secure sufficient safety in the on-slope start assisting function. SOLUTION: A car stop sensing means S1 (S1a-S1d) senses a car stopping and emits a stop sensing signal, and a computational processing means 1 emits a command signal for brake pressure in compliance with the electric signal to ...

PROBLEM TO BE SOLVED: To surely weld by a sideways sealer. SOLUTION: One face part 5b of a pair of sideways sealer face parts of a sideways sealer 5 comprising a pair of sideways sealer face parts 5a, 5b is pivoted on a sideways sealer arm 51b and a cutter 57 on a cutter arm 51a. These arms are pivoted on a pivot point 0 fixed on a main body one by one. The cutter is installed freely slidable on a...

PROBLEM TO BE SOLVED: To provide a sealing method of a heat fusible sheet for preventing fracturing a releasable tape occuring due to the differences of a thermal expansion coefficient between a plate heater and the releasable tape, and for preventing clinging of an adhesive material layer on the plate heater. SOLUTION: The sealing method of a heat fusible sheet comprises providing a plate heater ...

PROBLEM TO BE SOLVED: To deal with a problem generated in a relation to the abnormality of the hydraulic oil temperature sensor of an automatic transmission while an engine is automatically stopped. SOLUTION: The engine automatic stopping/restarting controller of a vehicle is provided with an oil temperature sensor abnormality determining means for executing the abnormality determination of the hy...

PROBLEM TO BE SOLVED: To suppress the blow-up of an engine speed due to the closing action delay of an ISC valve at the time of shift operation in operation. SOLUTION: Whether shift operation is made or not is judged at the time of lean burn operation (S5-S7), and when the existing of the operation is judged, a timer processing value is calculated (8), to spark-delayably correct ignition timing by...

A controlled self operating vacuum cleaning system which comprises a stationary housing for the storage of a mobile vacuum cleaner apparatus and where the housing is provided with an automatically openable and closable closure allowing exit and entry of the mobile vacuum cleaner unit. The mobile unit is driven by an internal drive motor which is powered by one or more batteries carried by the mobi...