PURPOSE:To enable a change of speed to be absorbed and to suppress the generation of vibration to a minimum limit, by delaying a decrease of the engine speed and clutch torque when an accelerator, after it is depressed, is released in a low speed region. CONSTITUTION:When a vehicle is in operation performing a shift to a running range, in case of deciding the vehicle to be in a drag mode by a drag...

PURPOSE:To improve fuel consumption of an engine and its output, by stopping the supply of fuel to the engine, when its operative condition satisfies a predetermined condition, and increasing a supply amount of fuel in accordance with selected shift patterns when the predetermined condition is not satisfied. CONSTITUTION:If an operative condition detecting means detects a deceleration condition, a...

PURPOSE:To ensure high braking efficiency by locking a rear wheel differential gear when an anti-lock state is conditioned on a split mu road surface under a four wheel drive. CONSTITUTION:When a right front wheel FR running on a low mu road surface is going to be locked with the brake applied, a system including both the right front wheel FR and a left rear wheel RL fall into an anti-skid control...

PURPOSE:To make it possible to reduce resistance of rotation, by setting a clutch means adapted to connect/disconnect the rotary motion between a case part on differential gears built-up body side and a case part on ring gear side, and disconnecting this clutch at a change to two-wheel drive. CONSTITUTION:A case part 32 on differential gears built-up body side can rotate on axles 10, 12, and suppo...

PURPOSE:To make it possible to prevent spatter of stones, heating of a tire and other troubles, by calculating idle running quantity of a driving wheel, from a detected value of car running speed and a detected value of rotating speed of the driving wheel, and outputting a shift-up forbidding order in case of that the calculated idle running quantity is over the preset value. CONSTITUTION:A calcul...

PURPOSE:To provide a foaming inhibitor capable of inhibiting or killing the foaming of slag by blending calcium aluminate as a base with specified amounts of Al and C, in a small amount and in a short time. CONSTITUTION:This foaming inhibitor for slag contains 20-50% calcium aluminate, 10-30% Al and 10-20% C or further contains the proper amount of metallic iron powder. Al and C in the inhibitor c...

Apparatus for temporarily disabling a translation lookaside buffer or TLB (60) in a computer system upon the occurrence of certain predefined system conditions. Such conditions may be of a first type which have been predetermined to indicate a greater risk that two or more virtual addresses stored in the TLB (60) will simultaneously match the incoming virtual address, and/or of a second type in wh...

A straw briquette press in the form of a towable machine is capable of gathering straw in the field or receiving this from another wheel machine and pressing it to form dimensionally stable briquettes with a density of approximately 1 g/cm<3>. The machine uses a high-speed finger press, which receives the straw from a conventional feeder arrangement. The finger press comprises two swivelling block...

Method for the production of concrete mass and the mass produced. The mass is used for production of air-entrained concrete with high climate resistance, especially high resistance against frost cracking. The method includes mixing of binder, ballast and an air pore forming substance and liquid for activation of the binder. Cereal storage protein as gluten or a dispersion of the same is used as th...

1451130 Coating with foamed rubber compositions POLYSAR Ltd 17 June 1974 [22 June 1973 (2)] 26679/74 Heading B2E [Also in Division C3] The underside of a woven ribbon polypropylene primary backing tufted with nylon yarn and pre-coated with a carboxy-SBR latex, and a sheet of woven jute fabric, are coated with a foamed rubber composition formed from a composition produced by adding a) ammonium sulp...

A process for preparing a smooth thin film based on high-molecular weight polypropylene in which the weight-average molecular wieght is at least 4 x 10<5>, the thickness is 10 mu m at most, the thickness is 10 mu m at most, the thickness distribution is 10% at most, the average degree of roughness is 2% at most, the maximum degree of roughness is 0.4 mu m at most.

The composition contains two different brominated epoxy polymeric components which are brominated diglycidyl ethers of bisphenol-A and epoxidized nonlinear novolak having at least about six terminal epoxy groups. The composition is suitable as impregnating agent in products comprising impregnated fibrous substrates. Such a product is for example the base material for printed circuit-boards. ...

1. Process for carrying out a combined gas turbine/steam turbine process in which the gas turbine process is carried out by means of a fuel gas which has been obtained from solid carbonaceous material and subsequently de-sulphurated, and the steam turbine process is carried out by means of the steam obtained upon combustion of the carbonaceous gasification residue, and in which the combustion of t...

Bi-oriented, heat-sealable and heat-shrinking films having good optical and mechanical characteristics, are obtained by means of extrusion and bi-axial stretching of a mixture of ethylene and alpha -olephin copolymers containing: a) from 95 to 99.9% by weight of ethylene/octene-1 copolymer; and b) from 5 to 0.1% by weight of an ethylene/butene-1 or ethylene/hexene-1 copolymer; with said cop...

A single-component, visible light-curable liquid adhesive composition having a viscosity of less than 25 centipoise at 25 DEG C which comprises (a) 2 to 20 parts by weight of at least one substantially pure phosphate ester having the formula CH2=C(R<1>).CO.O.R<2>.OP(O)(OH)<2> in which R<1> is a hydrogen atom or a methyl group, and R<2> is -CH2-CH2-, -CH2-CH(CH3)- or -CH(CH3)-CH2- and (b) 98 to ...

A single-component, visible light-curable liquid adhesive composition having a viscosity of less than 25 centipoise at 25 DEG C which comprises (a) 2 to 20 parts by weight of at least one substantially pure phosphate ester having the formula CH2=C(R<1>).CO.O.R<2>.OP(O)(OH)<2> in which R<1> is a hydrogen atom or a methyl group, and R<2> is -CH2-CH2-, -CH2-CH(CH3)- or -CH(CH3)-CH2- and (b) 98 to ...

PURPOSE:To properly actuate a liquid-crystal cell over a wide temperature range, by making plural driving voltages from a driving means equal to the optimum voltage in response to the intermittent change of one of plural auxiliary voltages to zero. CONSTITUTION:The optimum voltage which is determined by an optimum voltage determining means 6 decreases in accordance with the increase in the value o...

PURPOSE:To surely detect the deteriorated state or the like of a light emitting element by providing the titled device with a switching means to be closed at the input of coordinates to short a detecting resistor. CONSTITUTION:The optical coordinate input device is constituted of a driving circuit 1, a waveform shaping circuit 2, an amplifier circuit 3, a CPU 5, and the 1st and 2nd switching circu...