PURPOSE:To aim at making a drive device compact by disposing a final speed reduction gear in one of separating chambers formed by dividing a trans-axle casing with the use of a partition wall, and by disposing a center differential gear in the other separating chamber so as to arrange the center differential gear within the trans-axle casing. CONSTITUTION:The inside of a trans-axle casing 3 is div...

PURPOSE:To enhance the maneuverability of a combine by controlling a trunnion shaft so as to be rotated at a low speed during start or stop operation so that the starting speed is low but acceleration is high. CONSTITUTION:A potentiometer 2 always measures the travel position of a manual running lever 1 and delivers a signal to a controller 10 through an A/D converter 9. Similarly, a potentiometer...

PURPOSE:To secure the superior operation performance free from the reduction of revolution and engine stall by temporarily increasing the control duty of an auxiliary air control valve and increasing the air quantity when an automatic transmission changes from neutral to drive state. CONSTITUTION:An auxiliary air control valve 47 having an air passage which makes a detour around a throttle valve 4...

This coil possesses a former of electrically insulating material, provided with a first and a second end flange and in which are provided housings which receive two flat pins to which are welded the ends of the winding of the coil. Externally the second flange 14c has a peripheral groove 18 which itself has, in a lateral wall 18a directed towards the first flange 14b, two notches 20 able to allow ...

Il comprend un substrat de grille constitué d'alliage plomb-antimoine contenant un élément quelconque de sodium, lithium et potassium, et étain et dans lequel l'électrolyte contient des ions de métal alcalino-terreux.

Of the several illustrations, Figure 6 is self-explanatory: A new tyre (12) rotated by rollers applied to its outer periphery, has compression rollers (32) applied to its sides with a force sufficient to compress the rotating tyre as shown. - This procedure lasting a few minutes only, ensures that the new tyre embeds itself adequately into its wheel frame. After that, the wheel is balanced; no rep...

PURPOSE:To enable nearly black and white display and to obtain a high contrast ratio by disposing adjacent liquid crystal molecular axes so as to intersect orthogonally with each other and specifying the magnitude and direction of the twist angle at 1st and 2nd liquid crystal layers between substrates which sandwich the liquid crystal layers. CONSTITUTION:The 1st liquid crystal layer 4 and the 2nd...

PURPOSE:To prevent errors from being generated in reading of a record or in other operation owing to optical distortion or birefringence, by providing an optical recording layer on a specified polyester film comprising a polyester resin having a limit birefringence value of not more than 0.10. CONSTITUTION:A polyester film is produced by the usual method by using a polyester film having a limit bi...

PURPOSE:To make it possible to perform on-line measurement of a flash point simply and positively and to control the flash point efficiently, by measuring the flash point from a signal which is obtained by dividing the difference between gas concentrations at two points at specified temperatures by the difference between the specified temperatures at the two points. CONSTITUTION:Specified temperat...

Composite of rubber and metal reinforcement where the rubber contains a cobalt compound and at least one co-active compound. Composite is useful as reinforcement for rubber tires, industrial belts and hose.

PURPOSE:To obtain the title superconductive substance suitable for mass production and capable of providing wire rods and products of complicated shapes by heating a specified superconductive substance material to obtain vitreous melt, cooling, and crystallizing the melt. CONSTITUTION:A La-M-Cu-O or Y-M-Cu-O based superconductive substance material is heated to obtain vitreous melt (M is Ba, Sr, a...

PURPOSE:To obtain the title powder having the same stoichiometric composition as the composition in a soln. and metal by continuously introducing the specified aq. soln. contg. copper, a rare-earth metal, and an alkaline-earth metal into a fluidized bed reaction zone to simultaneously carry out thermal-decomposition oxidation and dehydration. CONSTITUTION:The following aq. soln. is prepared, and c...

PURPOSE:To obtain a homogeneous and fine composite metal oxide powder by adding an org. polybasic acid and glycol to a specified aq. soln. contg. copper, a rare-earth metal, and an alkaline-earth metal, heating the soln. to obtain a precipitate, and calcining the precipitate. CONSTITUTION:The following aq. soln. is prepared, an org. polybasic acid is added to the soln., glycol having a higher b.p....

PURPOSE:To make the critical current density of the titled ceramic body uniform and high by adding a specified binder to powder for a superconductive ceramic material, molding them, degreasing the molded body by exposure to a supercritical fluid and sintering the molded body. CONSTITUTION:A powdery starting material mixture for a superconductive ceramic material, e.g., composed essentially of Y2O3...

PURPOSE:To obtain the titled material having stable superconductive characteristics at the temp. of liq. nitrogen or above and undergoing no change with the lapse of time by substituting an element having a smaller ionic radius than Y for part of Ba or Y in a BaYCuO-based superconductive material so as to control the lattice constant of the a-axes of the rhombic crystals to a specified value or be...

PURPOSE:To obtain a molded oxide superconductor having a high critical current density by cooling density by cooling a soln. contg. oxide superconductor particles to a temp. below the critical temp. (TC) of the superconductor, applying an external magnetic field to the soln. and slowly vaporizing the solvent in the magnetic field. CONSTITUTION:A soln. prepd. by dispersing oxide superconductor part...

PURPOSE:To improve the productivity and workability of the title device by transferring the raw material to be sintered for an oxide superconductor with a conveyor, sintering the material in a sintering zone at a fixed temp., and annealing the sintered body in an annealing zone in an oxygen-contg. atmosphere. CONSTITUTION:The raw material 6a to be sintered for an oxide superconductor is placed in ...

PURPOSE:To intensify the C-axis orientation property of a crystal body and to obtain the title oxide superconductor having excellent critical current density by forming the oxide powder for the oxide superconductor or melting and then solidifying the powder to obtain a formed body, and heat-treating the body in a strong magnetic field. CONSTITUTION:The oxide powder (e.g., the mixed powder of Y2O3,...

PURPOSE:To increase the density of a green sheet and improve the dimensional accuracy of the same, by rolling the green sheet on a carrier film sequentially while heating it by a roll equipped with a heater therein. CONSTITUTION:Slurry 1, obtained by adding solvent or the like to super- conductive powder, is poured into a hopper 4. When a pulley 5 is rotated, the pulley 6 is also rotated and the s...