When a deceleration slip executing minimum gear stage is not established in a state of continuously executing a deceleration slip control at a target slip amount, it is judged whether or not an input shaft rotational speed of a transmission becomes a down shift judging rotational speed. When it becomes equal to or less than a predetermined down shift judging rotational speed, a down shift is execu...

L'outil abrasif est formé d'une phase continue comprenant des grains abrasifs liés par un liant organique, avec moins de 10 % en volume de porosité, la majorité des grains abrasifs étant sous la forme d'agglomérats résultant du frittage des grains avec un liant inorganique,; et d'une phase consistant en de 16 à 34 % en volume de porosité. L'outil qui a une dureté située entre J et S sur l'échel...

The device has an electric braking actuator (10), and a control unit (15) constituted by a handle (16) mounted on a support (17). An elastic unit (33) is compressed to generate a force that is reflected in a handle (16) via a cam (31), from a cross-bar (20) and a connection unit (22). The compression of the elastic unit is increased, when pivoting of the handle is increased i.e. braking requested ...

Un système d'accueil pour accueillir un utilisateur d'une automobile comporte un moyen de communication hôte (501) incorporé dans l'automobile, ou une installation (1160) à proximité d'un emplacement de stationnement de l'automobile. Le système comporte en outre un moyen de détection de distance (522-525) pour détecter une distance entre l'utilisateur et l'automobile en stationnement. Un moyen ...

Cet élément protecteur pour ordinateur portable destiné à être rapporté directement ou indirectement respectivement sur les faces supérieure ou écran (15) et inférieure ou base (16) de celui-ci, est constitué de moyens (9, 10, 30) venant se positionner au moins au niveau de chacun des quatre angles de chacune des deux faces principales (supérieure et inférieure) dudit ordinateur portable, chacu...

An integrated point of sale terminal for processing multiple payment types including payment by check includes a compact housing, a processor, and memory. The housing has a base shaped to sit on a merchant counter and has a document slot for receiving a check. The processor is disposed in the housing, and the memory is in communication with the processor. The payment terminal is located at the poi...

A limb for a breathing circuit manufactured from very thin walled polymer materials (40,44) has an elongate axial reinforcing spine (24) lying freely inside the conduit (25) and fixed to each end connector (23,49). The spine (24) is laterally compliant but axially stiff. The spine (24) provides resistance to tensile and compressive loads on the conduit (25), including that induced by prevailing in...

The system has an information acquisition unit to acquire information relating to functioning of an engine of a vehicle and conditions of movement of the vehicle. An analyzing unit (12) analyzes the information to determine a desired ratio of a gear box to be engaged. The unit (12) confirms or invalidates the ratio before delivering orders corresponding to control the box for engaging only the rat...

The method for identifying at least one object (6, 8) belonging to a list of objects selected from a larger set of objects present in a store comprises an automatic comparison stage (146) for a list identifier contained in the memory of a mobile terminal with a list identifier contained in the memory of an electronic tag which is the closest to said terminal in order to determine if the identifier...

The device has an actuator controlling module (26) to control an actuator (24) of a clutch (14). The module has a correcting unit to determine a control signal of the actuator for canceling variation between a nominal value and measure of a clutch control quantity in minimum amount of time. An adjusting unit adjusts parameters of the correcting unit according to physical quantities and actual beha...

The device has a multivariable governor (1) with a stage reconstruction block (2) for estimating stages of an engine, clutch, and transmission. A set point generation block (3) establishes transmission torque and engine speed set points based on commands from a driver. A control signal calculation block (4) generates engine torque and transmission torque controls to modify the clutch sliding, base...

The device has a gearbox control unit exchanging information with an engine control unit of a vehicle. The information comprises a torque request from a driver and an actual torque value provided by the engine. The gearbox control unit sends a request to the engine control unit for delivering torque higher than the requested torque in order to increase a speed ratio, when the requested torque is l...

The method involves initializing a computing network using two digital documents containing a digital certificate of the network and a digital document containing links to the digital pages for accessing the certificate. Computing objects are referred in specified address parameters located on servers. The certificate contains information of administrative and technical nature for accessing the ne...

The multifunction storage device (24) comprises at least one casing (26) located entirely behind an opening (22) of a trim element (18) placed in the driving compartment and supports several functional units (36,38,40). Each box is able to be subjected to a non-linear movement so that each of the functional units can be brought opposite the opening in order to be accessible.

The method involves downloading data having graphic animation and audio contents. Players for audio content and graphic animation content are downloaded and stored at operating system processing layer of a cell phone. A background task server (5) is downloaded and stored in the layer. The server activates one player (6) to play the graphic animation content when it detects the arrival of an incomi...

Dental filling material (A), of composite material (M) and intended for gluing into a cavity or dental canal, using a glue (B) that can be polymerized by photochemical initiation. Dental filling material (A), of composite material (M) and intended for gluing into a cavity or dental canal, using a glue (B) that can be polymerized by photochemical initiation. (M) comprises a resin-based matrix reinf...

The casing (20) has cooling fins (22) and deflectors (23) for favoring aerodynamic flow across the fins. The deflectors extend radially in a space separating the casing and a rim (11) and are regularly spaced along an inner annular edge (21) of the casing. The deflectors serve as a support to a fender (24) that surrounds a wheel (1). The deflectors assure the hooking of the fender through retainin...

L'invention concerne un vitrage feuilleté (10, 10') pour véhicule comportant au moins une feuille de polymère thermoplastique intercalaire (13, 16) positionnée entre deux substrats (11, 17), chaque substrat présentant ainsi respectivement une face (2, 3) tournée vers ladite feuille intercalaire (13, 16), ledit vitrage présentant des propriétés de réflexion dans l'infrarouge et/ou dans le rayonn...

Le système (200) comprend une mémoire stockant un ensemble de données volumétriques contenant des données visées et des données non visées à proximité des données visées, les données visées ayant un axe de référence qui passe par les données visées. Une unité de traitement est prévue, définissant au moins une tranche de référence et de multiples tranches du sujet à l'intérieur de l'ensemble de ...

The mould (1) consists of two hinged halves (1a, 1b) that move relative to one another as they open and close, and a lock (14) that extends the whole length of the opening edges. The lock consists of two hooks (17a, 17b) with facing recesses (18a, 18b) for a rotating wedging strip (19). The strip pivots adjacent to one hook and engages with the opposite one to lock the two mould halves in the clos...