PURPOSE:To provide such an arrangement for a car that it can run in full engagement of clutch even during low revolving speed of the engine, and that the clutch is not engaged violently under heavy load operation, by putting the clutch in full engagement only in case the car is running at a speed exceeding a specific value and the slip at the time is minor. CONSTITUTION:A clutch full-engagement co...

PURPOSE:To accurately judge an advance direction and prevent the occurrence of engine stall by judging that a gear shift direction is the same as the advance direction when the engine speed in the half-connected condition of a clutch is increased more than the engine speed in the disconnected condition, while judging that their directions are reverse when said engine speed in the half-connected co...

PURPOSE:To reduce possibility of overlapping of torque shock by instituting a speed change pattern into a line along a prescribed throttle opening, in a territory where a changeover pattern and a speed change pattern are mingled with each other. CONSTITUTION:A controller 5 is provided with a speed change pattern as a control map of an automatic transmission 4, and speed change control of respectiv...

PURPOSE:To secure both cooling and soundproofing effects and reduce the number of part items as well as to facilitate a job for assembly operation by partitioning off an inlet and an outlet with a cushioning material and forming both inlet and outlet ducts for cooling air in space between a transmission case and a case cover. CONSTITUTION:Cushioning materials 60-63 are installed in the inner part ...

PURPOSE:To hold a temperature of a friction engaging element at the time of starting within a predetermined value by holding a condition of change in a throttle opening within a permissible limit, set by a throttle control limit setting means, during the time from shift operation, from a stop range to a start range, to start completion. CONSTITUTION:A multistep speed change mechanism in an automat...

PURPOSE:To effectively utilize space above a crank case by respectively arranging an ordinary carburetor above higher part of upper surfaces of the crank case and a throttle opening sensor-provided carburetor above lower part of upper surfaces of the crank case. CONSTITUTION:In a two-cylinder type two-cycle engine which arranges one cylinder tilted to the front a little diagonally from a perpendic...

A reinforcement for thin film materials is provided by coating the films with an ink-type material. Ink coating of moisture vapor-permeable films such as polyurethane allows for a film suitable for use on skin which has an optimal rate of moisture vapor transmission. If desired, an adhesive can be provided on the ink-coated polyurethane membrane, and such materials are suitable fo retaining I.V. n...

Invention: X-Ray Image Equipment Inventor: of the Invention Soft x-ray radiation, which has a lower level of radiation, is transmitted to a target (i.e., the breast). The transmitted image of the target is refined through various computerized processes. All data is stored in a multiple image memory or filed in a laser having a large memory capacity. Stored images can be viewed on a TV monitor or r...

Deinking of paper having print during the production of recycled paper is accomplished by a froth flotation process using a hydrocyclone. A finely comminuted liquid solids used paper suspension having a consistency of about 1 to 4% is introduced into a generally vertical axis vortex provided in a hydrocyclone. Air is sparged into the suspension in the vortex, by passing through a porous inner wall...

Method for manufacturing a compound pipe the wall of which comprises an inner layer (23) of a first material and an outer layer (24) of a second material. Powders (13,14) of the two materials are isostatically hot pressed to form a cylindrical tubular blank (15) in which the first material (13) forms an inner layer and the second material (14) forms an outer layer, the blank after heating to a sui...

The invention provides: a blowing composition for producing foamed articles of polyurethane comprising at least one of chloropentafluoropropane and isomer thereof, a blowing composition for producing foamed articles of polyurethane comprising (a) at least one of chloropentafluoropropane and isomers thereof and (b) 1,1-dichloro-1-fluoroethane and a blowing composition for producing foamed articles ...

A shrinkable copolyester film having shrinkage of not less than 30% in the direction (main shrink direction) of either the machine direction or the transverse direction after 5 min treatment in an air oven at 100 DEG C, a shrinkage of not more than 20% in the other direction perpendicular to the main shrink direction after 5 min treatment in an air oven at 100 DEG C, an initial shrinkage stress (F...

A microcomputer (10) in a motor vehicle is supplied with regulated operating voltage through a regulator (12) and a semiconductor (11) for the microcomputer is supplied with voltage from the same vehicle battery, through a voltage divider including a Zener diode, for its chip-select input (CSA) which feeds in through a Schmitt trigger circuit such as to enable writing into the memory (11) when the...

Compositions for use in the production of molded articles, preferably by injection molding, comprise a ceramic powder and/or a metallic powder and an organic binder, wherein the organic binder comprises a polyalkylene carbonate and an epoxy compound having at least one expocy group in the molecule.

PURPOSE:To produce tires in different sizes effectively by providing interlocking operations of a parts manufacturing part, parts supplying part, and automatic molding line using a molding drum of a desired size through separating into a band, crude case, BT band, and crude tire molding part, and thereupon performing the control. CONSTITUTION:Molding control CPUs 51-54 and pre-stage control CPUs 5...

The invention relates to novel esters which contain fluorocarbon and oxypropylenealkyl ether groups in bonded form, of the formulae in which:   Rf is   a linear or branched, partially fluorinated or perfluorinated alkyl group having 2 to 10 carbon atoms,   a partially fluorinated or perfluorinated cycloalkyl group having 4 to 8 carbon atoms,   a perfluorophenyl group or   a perf...

PURPOSE:To manufacture rapidly solidified metal powder having high quality under excellent productivity by forming circular liquid layer of cooling water on inner wall part of funnel type cooling vessel having inclined center axis and injecting molten metal flow on the inner face. CONSTITUTION:The cooling vessel 1 having a large diameter cover 5, which has a through hole 4 for the molten metal flo...

PURPOSE:To surely protect a semiconductor storage device through a simple structure against latch-up caused by a parasitic transistor by a method wherein the bias of the isolating layer (N or P well) of a sense amplifier is made equal to the drive signal of the sense amplifier in potential. CONSTITUTION:In a sense amplifier 811, the drain and the gate of a PMOS 82 are connected to a bit line BL1 a...

A golf article retaining device adapted to be removably attached to a supporting surface. The device is formed of an elongated strip of spring material in a three leg configuration. The first leg has a free end and is bent at the other end into the second leg overlying the first leg to form a mounting recess adapted to receive the upper end of the supporting surface therebetween. The configuration...

A process for the production of mouldings having a density of at least 120 kg/m<3> from polyurethane foams having a compact surface by foam-moulding a reaction mixture comprising a) a polyisocyanate component, b) a reactive component containing groups which are reactive towards isocyanate groups, c) blowing agents and optionally d) further assistants and additives, where the blowing agents...