PURPOSE: To improve the efficiency in a manufacturing line by forming an acid filling route communicated with each cell of each assembled storage battery main body and a circuit to apply charging current in a forming plate. CONSTITUTION: An acid filling route communicated with each cell 35 of each assembled storage battery main body 30 and a circuit to apply charging current are formed in a formin...

PURPOSE:To improve start property at up-grade road by holding ON motion of a brake actuator till variation of input side rotating speed of a transmission becomes under the setting value corresponding to proximity of coupling of friction elements constituting the shift stage of start. CONSTITUTION:At stoppage, during operation of step-in of a brake pedal 82, a transmission Z is controlled to be neu...

PURPOSE:To surely remove the residual lap on a spool by arranging a rotary brush and a spike roller. CONSTITUTION:A rotary brush 20 revolves at a higher speed than a spool LB, and the residual lap L which is rewound is continuously removed by the tearing in succession from the top edge part. Then, a spike roller 30 shifts onto the rotary brush 20, and the residual lap L in form of fiber scrap is s...

PURPOSE: To provide a lighter weight and a smaller space by connecting both ends of a yarn guide member through a power transmission mechanism and synchronizing the motion of supporting levers for this mechanism. CONSTITUTION: For the turning motion of a sheet 14 to be changed from a start position to a yarn change position by supporting levers 12, 13, a lever 42 provided with the sheet 14 to be c...

PURPOSE:To avoid a re-try action caused by the insufficient cut-off of a clutch, by making an actuator operation quantity, whose purpose is to put a dry type single plate clutch into a cut-off state at the time of a gear change action on and after a 2nd time, larger than the 1st time operation quantity. CONSTITUTION:An automatic transmission 3 controller, at a time of speed change, puts a dry type...

PURPOSE:To prevent a shift hunting by using a car speed at a point of time of a car wheel speed change from deceleration to acceleration during traction control, as a speed change decision factor until next car wheel speed change from deceleration to acceleration is detected. CONSTITUTION:A traction controller (c) conducts an output control of an engine (b) according to a drive wheel speed and an ...

PURPOSE:To perform speed change with no shift shock and little clutch load by modifying a speed change pattern according to the difference between the measured value of the net average effective pressure and the predictor of the net average effective pressure at the time of the speed change pattern being set. CONSTITUTION:A speed change control means A controls the speed change of an automatic tra...

PURPOSE:To obtain a novel sunlight selective absorbing membrane by providing a composite layer consisting mainly of a composite of metal carbide and metal nitride. CONSTITUTION:A sunlight selective absorbing membrane is provided with a composite layer 2 consisting mainly of a composite of metal carbide and metal nitride formed on a base plate 1 and with an oxide layer 3 formed on the surface of th...

PURPOSE:To prevent effectively an engine from prefiring due to quick opening of an accelerator in the start of a vehicle by hastening the speed change start of a speed change controlling means responsive to the accelerator means earlier than the start time of engine rotation rise by a predetermined time. CONSTITUTION:When a vehicle is stopped under the idle running, an axle 22, a second transmissi...

Compounds of the general formula; (wherein R represents -CH(CH2OH)2 or -CH2CH(OH)CH2OH) possess a package of favourable parameters which render them of particular use not only in all forms of intravascular visualisation but also in myelography. The compounds are prepared by reaction of the corresponding 5-monoacetylamino compound with one or more reagents effective to introduce the 2-hydrox...

An automatic transmission system has a controllor for controlling the slip rate of a clutch in accordance with the amount of depression of an accelerator pedal instead of controlling the ON/OFF condition of the clutch by a control signal when it is discriminated that the gear change position of a transmission and the amount of depression of the accelerator pedal are in the predetermined states. In...

In a process for monitoring the mechanical displacement of the armature of an electrovalve actuated by a magnet winding by means of a signal derived from the current flowing through the magnet winding, the induction of the magnet winding is monitored and the change of inductance at the switching points of the electrovalve is raised up to a detectable signal level by an outer power supply. A device...

In the case of a process for making a container, such as for example a can or tube for receiving a product, after making the container its inside is primed. A coating is applied to this primer in a layer thickness of 30-70 mu , a plastic, preferably a polyolefin or the like, being used as coating.

In the prodn. of bipolar lead/lead dioxide electrodes for galvanic primary elements, the substrate foil acting as the carrier electrode is coated on both sides simultaneously in a galvanic bath, in which are arranged one or more carrier electrodes, each clamped between two terminal electrodes made of lead and/or an acid-proof metallic conducting material. The electrodes to be galvanically coated a...

The battery plate filling device uses a dosing pump for injection of an active mass via jets into the annular space between the tubular sleeve and the grid core of the cylindrical battery plates. A platform (A) displaced perpendicular to the filling direction supports two workpiece carriers (B, C), one next to the other, with a pivoted plate (D) mounted on the platform (A) between them. The plate ...

A structural component of sintered polycrystalline ceramic, formed as a friction disc or as a disc brake, which is used as a thread guide element or processing element in textile yarn production and processing machines is sintered to produce the required dimensional accuracy and is then machined and has, at least in the regions intended for thread contact, after machining, a surface which is forme...

2066740 9104810 PCTABS00003 A ball mill for use in mechanical alloying and grinding comprising a plurality of ferromagnetic balls (22) within a spherical or generally cylindrical chamber or cell (20) of a paramagnetic material. The cell has a substantially horizontal axis of rotation (21). At least one magnet (24) is mounted outside the chamber to produce a magnetic field within the chamber. The o...

A method and apparatus for detecting the traveling position and direction of an unmanned vehicle of an autonomous guidance system, wherein pairs of marks are provided along a course on which the unmanned vehicle is to travel and disposed perpendicularly to the course respectively, and at the unmanned vehicle are provided sensors which can detect the marks and specify the relative positions of the ...