PURPOSE:To prevent the fall of driving force at supercharging and always insure good acceleration by detecting supercharged condition of an engine, and regulating the shift-up motion of an automatic transmission at the rise of supercharging pressure. CONSTITUTION:Output of an engine A is transmitted to driving wheels C through an automatic transmission B. On the other hand, a supercharger E is mou...

PURPOSE:To dissolve troublesome operation for start of a vehicle by deciding coupling characteristic of a clutch due to the setting content which is set by a setting means according to the load condition of the vehicle, and also deciding the gear position of a geared transmission at start. CONSTITUTION:When a key switch SW is at ON position, it is discriminated in a control unit 6 whether an inter...

Use of polyfluoroalkanes of the formula CX3-CY2-R (I> in which X radicals on the same C atom stand for hydrogen and/or fluorine, Y radicals on the same C atom stand for hydrogen, fluorine and/or CF3 and R stands for CH2F, CHF2, CH3, CF3, CF2-CH3, CF2CH2F, CH2-CH3, CH2-CH2-CH3 or -CH(CH3)-CH3 and a molecule of the formula (I) contains at least two fluorine atoms, as propellant gases. o

Use of polyfluoroalkanes of the formula CX3-CY2-R (I> in which X radicals on the same C atom stand for hydrogen and/or fluorine, Y radicals on the same C atom stand for hydrogen, fluorine and/or CF3 and R stands for CH2F, CHF2, CH3, CF3, CF2-CH3, CF2CH2F, CH2-CH3, CH2-CH2-CH3 or -CH(CH3)-CH3 and a molecule of the formula (I) contains at least two fluorine atoms, as propellant gases. o

a guiding line (L) extending along a running track: and a conveyor cart (A) including, detecting means (6) for detecting the guiding line (L) and outputting detection data, steering control measn operable in response to the detection data for permitting the conveyor cart to automatically run along the guiding line (L); said detecting means (6) being switchable for selectively detecting right and l...

In a well testing tool system for isolating vertically spaced portions of a well bore and measuring well conditions such as pressure, and temperature, and including a wireline supported tool train and a locking sub connectible on a removable lock mandrel for releasably locking the tool train in a well bore, the tool train has a locking probe releasably connectible in the locking sub, a probe mandr...

PURPOSE:To form the high-temp. superconducting thin film having a precisely controlled composition by using an oxygen ion conductor as a substrate, and vapor- depositing the thin film of a metal on the surface of the substrate while supplying oxygen to the surface from the inside of the substrate. CONSTITUTION:The inside of a vacuum vessel 4 is separated into a small chamber 6 and a vapor-depositi...

PURPOSE:To form an oxide superconductor layer having superior adhesive strength by dividing a target in half and constituting the target of a material forming an oxide superconductor layer and a material forming a buffer layer, carrying out laser irradiation, and forming the superconducting layer via the buffer layer on a base material. CONSTITUTION:A target T1 is constituted of a section t1 formi...

PURPOSE: To transmit the data by crossing a threaded junction part without requiring the electrical connection by providing a sensor for generating the data signal and a Hall-effect connecting device, and transmitting the data signal while utilizing the electromagnetic phenomenon. CONSTITUTION: A Hall-effect connecting device 327 formed of a Hall-effect receiver 331 carried by a tubular member 319...

PURPOSE:To easily read out only a DC component in reproducing a picture by respectively and collectively recording orthogonally transformed DC component data and AC component data in a recording medium at every picture. CONSTITUTION:When an electronic still camera 200 photographs a color still picture in an object field with an image pickup device 34, the color still picture is converted into digi...

PURPOSE:To obtain an excellent seat shell as for rigidity and productivity by stamping a stamping material made of polyethylene terephthalate resin containing glass lint as a main reinforcing material. CONSTITUTION:A seat shell 1 is utilized as a core member for a seat of an automobile and the like, for example, it is formed into the shape as shown in the figure out of plastic material. In this ca...

PURPOSE:To obtain a seat, which can be utilized as a bed with a single room while sufficiently ensuring the number of persons to be accommodated, by dividing a passenger room, accommodating a large number of persons, into two or more sections by a tilt partition along a width direction of the passenger room and vertically providing the seat between the partitions along them. CONSTITUTION:In the ca...

PURPOSE:To prevent a short-cycle operation, in which the air discharged is taken in again, by providing at the air outlet in a casing a duct for the discharged air which is extended approximately at right angles to the direction of the air blown out. CONSTITUTION:An attachment 8 for an air-discharge duct is mounted on the top side of a casing 41 with an opening in alignment with the air outlet. An...

PURPOSE:To eliminate impingement of a current of discharged air against a floor, such as that of an overhanging veranda, in order to prevent a short- cycle operation and also to dispense with an air-discharge duct along a veranda in order to improve lighting by providing at the air outlet of a casing a blowing guide for controlling the direction of the air blown out. CONSTITUTION:Over an air outle...

The present invention relates to a process for making bioactive coatings on osseous prostheses, wherein, from solutions, a mist of particles containing calcium ions and orthophosphate ions is made and said mist is brought into contact with an implant made of inert material under such operational conditions that at least one desired calcium phosphate is formed by reaction on the hot surface of said...

Process and device for increasing the rate of solution of gas in a liquid. A mixture of a liquid and gaseous component is fed into a covered channel for secondary mixing, said secondary mixing channel being disposed in an elongated circulation oxidation ditch. The energy of the mixture flowing out of the secondary mixing channel impels the liquid in the channel in the direction of the longitudinal...

PCT No. PCT/SE85/00460 Sec. 371 Date Sep. 24, 1986 Sec. 102(e) Date Sep. 24, 1986 PCT Filed Nov. 18, 1985 PCT Pub. No. WO86/04294 PCT Pub. Date Jul. 31, 1986.A device for braking the saw chain (3) of a portable power saw (1). The power saw has a front handle (5) to be gripped by one hand (6) of the saw operator, and a rear handle (7) to be gripped by the operator's other hand (8). The device inclu...

P.C. 7548 METHOD AND APPARATUS FOR IMPROVEMENT OF BONE HEALING A method and apparatus 10 are provided for improving bone ingrowth into prostheses and for stimulating living bone attachment onto prostheses and for bone healing in general wherever two bone surfaces are to be joined, for example in fractures and in osteotomies. Bone particles are sprayed under particular conditions and with a particu...

A dosage unit for dosing a number of measured quantities of a liquid, such as an insulin preparation, from a separate cartridge (2), where the dosage unit comprises a cylindrical casing for the cartridge (2). At the distal end the casing (1) is provided with means for fastening a liquid outlet needle (5). The dosage unit comprises furthermore a piston rod (8) activating a piston (4) in the cartrid...

Metals contained in a hydrocarbon containing feed stream are removed by contacting the hydrocarbon containing feed stream under suitable demetallization conditions with hydrogen and a catalyst composition comprising zirconium phosphate and a metal phosphate where the metal is selected from the group consisting of nickel, iron, vanadium and cobalt. The life and activity of the catalyst composition ...