The tricycle has a trunk or a child safety seat, and a frame including, at its front end, a yoke (3) with a front steering wheel (4) and a handlebar (2). The frame has, at its middle part, a vertical tube supporting a saddle (15), and, at its rear end, two rear wheels (10, 11) in the same axle and a handlebar (12) of a height of about 1 meter. The distance of the point of projection of the steerin...

Un obturateur de capteur (400) positionnable dans une perforation (402) traversant une paroi d'un puits de forage pénétrant une formation souterraine est fourni. L'obturateur de capteur (400) comprend un manchon d'obturateur (410) positionnable dans une perforation traversant la paroi d'un puits de forage, une broche (412) positionnable dans le manchon d'obturateur (410), un capteur (422) et un ci...

The bed has a bedspring frame mounted on a base (4). A deployment/ folding mechanism has an activation unit (6) with a base arm (62) and an active arm (61) forming a bent between them. The arm (62) is mounted rotating on an intermediate frame (41) of the base and the arm (61) is mounted on a foot part (3) of the base by a rotative connection (611). The arm (61) takes variable configuration with re...

The method involves dividing a surface (10) defined by a perimeter into zones of width adapted to be covered by a motorized device. The device is connected by a link (18) to a reference point (PR), and displacement of the device along the zones is ensured by controlling tension, length and angle of the link with displacement direction of the device such that the device covers each zone during its ...

The machine (10) has a forward viewing camera and infrared sensors to avoid ground objects and a vertically viewing camera (14) with a fisheye lens which interprets data from ceiling (33) mounted transmitters (31) to guide it over the cleaning path.

The longue has a support structure (26) articulated at an inclinable part (18) and having a crosspiece (32) whose ends (34) cooperate with the notches (40) of a U-rail (36). Each of several side rails (12) has a retaining cage (42) placed opposite to the notches. The cage avoids the corresponding end of the crosspiece from slipping from the side rail, while allowing the end to move from one notch ...

The method involves determining an imaginary time of a site representing a state of advancement of each production run in progress and defined at each timing instant (ti). A data representing the imaginary time of site is distributed in parallel to different operators (Op01-Op089), for synchronizing the operators with respect to the production run in progress. An independent claim is also included...

The method involves gathering different documents (2) filed by respective persons present in a meeting so as to constitute an attendance register (38), where the documents are priorly transmitted to each of persons invited to the meeting. Data relative to the invited persons are processed from data provided by the filed document for determining values relative to the persons whose document has bee...

Cette invention décrit un système et un procédé pour transaction en ligne. Le système incorpore un protocole de communication DVB-H (53) dans un appareil de communication portable (51) pour recevoir et visionner des publicités multimédia à partir d'un fournisseur de télévision numérique. En outre, le système incorpore un programme logiciel dans l'appareil de communication portable (51) pour traite...

The invention relates to a vacuum pumping circuit comprising: an upper chamber (34) and a lower chamber (36) that communicate via a connecting orifice (38), and comprising a valve (40) provided with a stem guided so as to slide along a vertical axis (A1) in order to close the connecting orifice (38), which circuit is characterized in that the valve stem (48) is provided with a section forming a pi...

The method involves identifying structural and non structural pixels in image data by analyzing the data in two and three dimensions. The image data are additionally processed in two dimensions based on the identification of the structural and non-structural pixels. The structural pixels are identified relative to the amplitude value of gradient calculated from three-dimensional data and to the di...

The method of inscribing a data carrier (10) with pictorial information. involves obtaining characteristics relevant to recognition by means of a spatial analysis of the original picture, by using filters. A line drawing is obtained in vectorized f by the intermediate storage and or the inscribing of the picture on the data carrier. The line drawing is transformed or integra in a security backgrou...

A mould incorporates an imprint for producing a honeycomb piece from expanded polymer balls to act as a lost model for fabricating a casting. It has some channels traversing its wall, emerging in the imprint and outside the mould, realised as slots extending parallel two by two and at least partially following the contours of the mould imprint. The channels allow the escape of air contained in the...

The process, in which a layer of a supple covering material (5) is inserted in a mould which is then filled with an expanding polymer foam before a rigid backing panel (2) attached to a mould cover (8) is fitted in place, has the backing panel made with turned-over edges (12) that press against projecting lips (11) on the edges of the covering layer to create a sealed joint as the foam is expanded...

The pallet has a tray supported by blocks (6-9), and a blank (1) comprising sliders (3a, 3b) with longitudinal and transversal bands (4a-4d). The bands (4a, 4b) have an arc shape attachment with a hole. The bands (4c, 4d) have two arc shape ribs (16) receiving, positioning and retaining the attachment. A lug (17) penetrates into the hole. The blocks (6) have a wall unit (18) coupled to the slider ...

The nucleic acid sequence encoding the porcine factor VIII A2 domain is disclosed.The nucleic acid sequence encoding the porcine factor VIII A2 domain is disclosed.

The procedure consists of printing a lengthwise roll of plastic film (1) with the information required for the label, on one or both sides. The film is then folded over along its Center line (1c), its edges are trimmed off to form a double lengthwise strip, and this is then welded transversely at intervals and cut along the transverse weld lines to make a series of sleeves.

This invention relates to a method for managing a software application functioning in a multi-computer architecture (cluster). This management is applied, for example, to the analysis or modification of its execution environment, in as transparent a manner as possible vis-à-vis this application. This management is applied to operations of analysis, capture and restoration of the state of one or mo...

The prosthesis, having metacarpal and trapezoid components, with the latter comprising a cup (15) and liner, has the cup made with external (20) and internal (23) sharp-edged projections round its outer and inner rim to engage with the trapezoid bone and insert respectively. The cup's outer surface also has four evenly-spaced points (21) and a coating of a substance such as calcium hydroxyapatite ...

La présente invention a pour objet une composition cosmétique ou dermo-pharmaceutique ou dermatologique comprenant, en tant qu'agent actif, dans un milieu cosmétiquement ou pharmaceutiquement acceptable, au moins un composé susceptible d'activer la synthèse des protéines SIRT dans les cellules de la peau. La présente invention a aussi pour objet l'utilisation de ladite composition.; A cosmetic der...