PURPOSE:To arrange so as to be economically advantageous by assembling rotatably pinion gears against a pinion gear shaft through an eccentric ring and limiting the change of a prior constituting member to a minimum. CONSTITUTION:A plurality of long holes 31b extending in the axial direction ot side gears 34, 35 are formed at the main body 3la of a differential case 31 at a center differential 30,...

PURPOSE:To prevent a differential case from vibrating at high revolutions in the titled device having a differential device of bevel gear, between-shaft type by supporting freely rotatably both ends of a differential case respectively at an extension housing and an output shaft via bearings. CONSTITUTION:Both ends of a differential case 6 are supported freely rotatably respectively at an extension...

PURPOSE:To film-pack even a bulk article having unstable shape without any hindrance by equipping an apparatus with a seal edge-holding means for holding the inside of the longitudinal sealed part of a doubling film from both faces for the period from the time of supplying an article to the time of operating art L-type sealer. CONSTITUTION:The lower end of a doubling film 12 is sealed beforehand b...

PURPOSE:To improve acceleration at the time of speed change by providing a valve for discharging a pressure oil in the defined oil chamber in a modulation valve to a drain, lowering a lock-up oil pressure to a defined pressure at the time of speed change and, after maintaining this oil pressure for a defined time, gradually increasing the oil pressure. CONSTITUTION:At the time of speed change a lo...

PURPOSE:To make it possible to simply and surely change over the drive mode between high and low speed drive modes, and between four and two-wheel drive modes, by providing such an arrangement that shift forks for change-over devices are shifted in the axial direction thereof by means of cam grooves in a drum member rotated by a motor. CONSTITUTION:When a drum member 30 is rotated by a motor 32 in...

A shaft for centrifugally separating a sample includes a first shaft element having a first end taper portion and a middle straight portion, and a second shaft element having a second end taper portion. The first shaft element and the second shaft element are coupled and rotate in opposite directions. An adapter having a ring is mounted on the rotating first taper portion of the shaft by the ring....

PURPOSE:To make it possible to continue the operation of floor heating type space heating surely even when there is insufficient sun light by providing an auxiliary space heating coil in a handling box and connecting the coil to a boiler exclusively used for pace heating. CONSTITUTION:When an indoor temperature sensor indicates the room temperature below a set temperature, a boiler 24 specializing...

PURPOSE:To distribute engine power economically and optimally by constituting engine output characteristic variably according to the kinds of loads (whether in working or running condition) of a wheeled type construction machine. CONSTITUTION:A small signal priority circuit 6 is arranged to receive outputs of a calculation circuit 3 calculating target injection rate according to outputs of an acce...

PURPOSE:To prevent lubrication oil from entering into a different area, by disposing two opposed oil seals between conical roller bearings or angular ball bearings for supporting a shaft, and by communicating a breather passage with the gap between the oil seals. CONSTITUTION:In such an arrangement that one end of drive pinion shaft 12 is journalled by means of a plural row type tapered roller bea...

A transfer case operation mode shifting apparatus used on a vehicle equipped with part-time four-wheel drive which having a center-differential shiftable between a differential-locked and differental-free drive mode of operation and between a two-wheel and a four-wheel drive mode of operation and a transfer shiftable between a high-speed range and a low-speed range drive mode of operation. The tra...

A container for carrying a uniform, fan-folded stack of plastic sheet assemblies and for allowing the assemblies to be conveniently dispensed, one at a time, with minimal risk that the stack will become jammed. The stack of assemblies is retained behind a constriction within an elongated chamber having a corresponding shape and slightly larger size. Pulling the forward-most assembly through a narr...

PURPOSE:To eliminate possibility of easy shortcircuiting of each joint piece by arranging joint pieces with different polarities grouped over and under electrode plates, and placing one of the electrode plates in a sack-shaped separator. CONSTITUTION:A joint piece 13 in connection with a positive electrode plate 11a is situated at the bottom of a group of electrode 7a, while another joint piece 12...

When a main stack 1 is to be withdrawn, it is lowered and one or more wedges 12 are rotated about shaft 6 until they lie on top of the stack to form between the stack and subsequently arriving sheets 4 a space into which a rake 14 is inserted. Further lowering and withdrawal of the stack permits the wedge(s) to assume normal rest position (pointing vertically downwards). A new pallet is brought up...

Zur Verbesserung der Probebogenentnahme am Ausleger einer Druckmaschine ist eine Blasvorrichtung auf der Bedienungsseite des Auslegerstapels 2 vorgesehen. Sie besteht aus einem oder mehreren Blasröhrchen 10. Diese sind mit den Bogenhochhaltern 9 und den Vorderkantenanschlägen 8 zusammengeschaltet. Bei Einfahren der Bogenhochhalter 9 und Abklappen der Vorderkantenanschläge 8 erzeugen die Blasröhrch...

In an automatic transmission control system provided for an internal combustion engine (M4) having an automatic transmission system equipped with a traction control system in which a throttle valve (M2) is adjusted towards a closed state from a throttle position corresponding to an operation of an accelerator pedal (M1) when wheel slippage occurs, a detection unit (M6) detects a degree of operatio...

The machine has a housing 10 containing a receiving space 11, two rotating disks 15 and 16 disposed at opposite sides of space 11, a plurality of parallel shafts 17, a first transmission axle 18 capable of driving the disks 15, 16 and the shafts 17 to undertake joint rotation, a second transmission axle 19 a transmission means 20 to actuate the shafts to undertake self-rotation, (a) motor (s) 23, ...

It is an outer layer dipping catalyst used in the prodn. of vinyl-acetic ester by ethylene, acetic acid and oxygen-containing gas. The yield of vinyl-acetic ester is more than 661 g per litre catalyst, per hr. at 150 deg.C. It consist of (1) a catalyst carrier which particle diameter is about 3-7 mm and pore volume is 0.2-1.5 ml/g, (2) palladium and gold distributed in outer layer of 1.0 mm thick ...

This invention provides a method for joining textile yarns to restore their continuity each time this becomes necessary in a winding unit, by means of a joining device which operates by means of several successive steps, one following another, to achieve a continuous connection, in said method the individual operations involved in the joining being independent of each other and being autonomous an...

The present invention relates to a kind of lead wire electrode body composed of metal lead or lead alloy made wire and the new type lead accumulator composed of said lead wire electrode body. The advantage of said lead wire electrode body is that the lead oxide is not easy to peel off while working. The advantages of the new lead accumulator are large capacity, stable performance and long service ...

Batteries for boats and vehicles require a CRA (cranking) battery 23 and an AUX (auxiliaries) battery 22 to ensure a start. The preferred version has an AUX battery made of parallel plates and a CRA battery made of parallel plates lying in a monobloc case in face to face positions. Each battery has a pair of CRA terminals 20, 30 for the electric starter and a pair of AUX terminals 19, 31 for the A...