PROBLEM TO BE SOLVED: To provide a negative electrode absorption type stationary lead-acid battery, capable of eliminating work space on the upper surface of each monoblock type battery container. SOLUTION: This lead-acid battery has positive and negative output terminals 2A and 2B on the upper surface of a monoblock type battery container 1, in such a state as eccentrically located toward the sid...

PROBLEM TO BE SOLVED: To suppress early deterioration in high rate charging and discharging, to improve a life characteristic at the time of repeating the high rate charging and discharging. SOLUTION: A battery power generating element is added with metal fluoride. Here, the metal fluoride preferably is at least one among germanium fluoride, silicon fluoride, tin fluoride, lead fluoride, calcium f...

PROBLEM TO BE SOLVED: To provide a lead-acid battery preventing deterioration in charge acceptance and capacitance drop due to the insufficient charging, even at the time of increasing the amount of lignin for preventing early deterioration in a high rate charging and discharging even when repeating a charging and discharging cycle. SOLUTION: The amount of ligninadded to a negative electrode activ...

PROBLEM TO BE SOLVED: To provide a lightweight expanded grid excellent in discharging and service life by forming a unfolded mesh part in the center of a lead or lead alloy sheet, and forming nonunfolded parallel frames and the lug parts for straps corresponding to the extension on both sides. SOLUTION: A lead or lead alloy sheet is unfolded in the width direction to form an expanded grid composed...

PROBLEM TO BE SOLVED: To realize electric energy loss reduction, miniaturization and weight reduction, as well as cost reduction of a change gear by realizing continuous transmission function with a motor of small capacity. SOLUTION: An engine 1, planetary gears 4, 6 and motors 8, 9 controlling sun gears of the planetary gears are installed. A planetary is connected with an input shaft driven by t...

PROBLEM TO BE SOLVED: To enable small power driving at the time of fastening, and miniaturization of size while ensuring holding power, in fastening equipment and a clutch which are used in a hybrid vehicle. SOLUTION: This hybrid vehicle is equipped with an engine 1 driven by combustion of fuel, a generator 5 driven by electric energy, a differential mechanism 4 which changes the rotating speed of...

PROBLEM TO BE SOLVED: To effectively prevent an accumulating device for driving a motor from becoming incapable of performing regeneration control because of a fully- charged state, by finding the degree of grade when going down a slope, and by correcting regeneration amount from a motor to the accumulating device in accordance with the degree of grade. SOLUTION: Under the control of a regeneratio...

PROBLEM TO BE SOLVED: To ensure precise load measurement while simplifying the structure by constituting a load measuring instrument using a bolt such that an unnecessary external force does not act on a strain gauge even if an external force acts on a lead wire. SOLUTION: A bolt 12 is provided a bottomed containing hole 17 continuous coaxially to a tool engaging force 16, a lead out hole 18 and f...

PROBLEM TO BE SOLVED: To generate a strong electric signal, even in the case where a chemical substance concentration of a target is extremely low, by containing conductive metal particles selected from the group comprising fine powders of a platinum group metal and its mixture, modified graphite, and a thermoplastic polymer with specific weight precentages, respectively. SOLUTION: This conductor ...

PROBLEM TO BE SOLVED: To easily design the image of a GUI(graphical user interface) operation screen and also an operation via a GUI operation and by means of a general-purpose software parts. SOLUTION: The index information on the attributes of software parts, events and messages are read and these index information are stored in a storage means. The optional names are set to these attributes, ev...

PROBLEM TO BE SOLVED: To control the useless radio wave transmission of a node device inside an isolated area made uncontrollable from a base node device and to prevent radio wave interference to the surroundings. SOLUTION: When the radio equipment 120a of the node device 100a and the radio equipment 110e of the node device 100e fail inside a network, a state where the node devices 100b, 100c and ...

Aqueous spray-resistant and pourable foams (S), produced by mechanical foaming of corresponding aqueous compositions (W), wherein the aqueous phase contains(A) a curable polymer system, which consists of(U) an ionomeric polyurethane or a mixture of ionomeric polyurethanes and optionally(P) one or more further polymers curable at least together with (U),and (B) at least one foam-stabilizerand the l...

The boot (3) binding for a snow board (2) has a section (1) fixed to the boot, a second section (19) fixed to the board and an adaptor (14) connecting these. The boot section and adaptor are releasable under excess load. The board section and adaptor are fixed together automatically and manually releasable.;

Interface de liaison entre une chaussure (3) et une planche de glisse (2) comprenant es...

At a procedure to, at a telecomunication and data communication system, temporary lend local resource (10) in said system to service and/or goods/product supplier for delivery of service or product by said resource, the allocation of the local resource is performed by utilization of Jini-based platform (14). A telecommunication and data communication system includes local resources (10) and set up...

PROBLEM TO BE SOLVED: To make it possible to predict the future values of variables as probability distribution for various values included in the variable by providing the predicting method with a step for forming the partial prediction of future values from respective reference sequences and a step for predicting a future value as the sum of weighted partial prediction values. SOLUTION: After th...

PROBLEM TO BE SOLVED: To provide a current lead which is tolerant of thermal shrinkage and electromagnetic force without increase in heat penetration. SOLUTION: In a low temperature-side part of this current lead, a support 302 is provided with a channel. A sheath type high-temperature superconductor 300 is inserted in layers in the channel. Then, the support 302 and the sheath type high-temperatu...

Method and data processing system for determining the type, the number and the volume of financial instruments for funding of a loan with an interest rate adjustment with an equivalent proceeds to a debtor, the loan being at least partially refinanced during the remaining term to maturity of the loan. In the data processing system, data are loaded, which data indicate the principal of the loan, th...

A method and device for recording signals on a record carrier with the aid of a radiation beam (15). The signals are recorded in the form of optically detectable marks in parallel tracks which have a substantially constant track pitch. The recording intensity of the radiation beam is set in such a way that with a "minimum" recording intensity information patterns are recorded with a low desired er...

Purification of aqueous medium contaminated with Sn by treatment with alkali metal silicate and removing the solid product formed.

Customers may examine communications contracts available from providers (1,2,3) and then complete them from customer terminals (4,5,6). The customer and provider terminals use a telephone network (100) to connect to an Intranet (101) which has security and routing units (9,8) and a server (7) able to access product and customer databases (30,31). Specific provider data may be accessed from a serve...