PROBLEM TO BE SOLVED: To prevent the resonance of a countershaft as a part of a driving force distributing mechanism. SOLUTION: This differential device comprises a differential mechanism 5 for distributing the driving force of an engine to the axle shaft 65, 67 sides through the output gears 61, 63, a transmission mechanism 26, and a driving force distributing mechanism 7 comprising the clutches ...

PROBLEM TO BE SOLVED: To presume the drive directing with high respondency to the change of the drive directing of a driver. SOLUTION: An input enumeration part 20 extracts a vehicle condition of every driving operation and a vehicle condition of every specific time, on the basis of a signal from a vehicle sensor signal input part 10. A road environment presuming part 30 presumes the road environm...

PROBLEM TO BE SOLVED: To control the driving force by which an engine is operated in a operational stability point of the lowest fuel consumption to the target driving force, even when a torque convertor is in a convertor state. SOLUTION: Whether the operational stability point exists or not, is checked on the basis of whether the engine output torque Te in 17 is agreed with the absorption torque ...

PROBLEM TO BE SOLVED: To lighten a shifting shock to smoothly start and restrain enlargement of the device by providing a second oil pressure generating means capable of supplying oil pressure by which a frictional engagement element for forward or backward becomes directly before engagement, when an engine stops during operation of a vehicle at setting a shift lever on the forward or backward pos...

PROBLEM TO BE SOLVED: To prevent the engagement shock of an one-way clutch in an automatic transmission without depending on a lock-up-off, in the conversion from the coasting travelling to the power-on travelling. SOLUTION: In the conversion to the power-on travelling, where the coasting travelling is determined in the last time in 21, and the pedalling of the accelerator pedal is determined this...

PROBLEM TO BE SOLVED: To provide a folding device in a packaging device which can dispense with a large-sized suction mechanism or a chain roller of complicated structure, is simple in construction, capable of surely folding films, and excellent in the finish of the surface of a packaged body. SOLUTION: A film folding device comprises film holding bodies 18, 19 comprising a pair of rollers which a...

PROBLEM TO BE SOLVED: To obtain a material showing improved strength which can be handled without decreasing excellent transmittance for visible rays and heat insulating property of a silica aerogel by incorporating a resin which is soluble with a solvent used for supercritical drying and has specified transmittance for visible rays and thermal conductivity into an aerogel. SOLUTION: As for the so...

PROBLEM TO BE SOLVED: To provide a transparent porous body for heat-insulating, capable of being handled and drastically improving the strength without substantially deteriorating the excellent visible light transmittance and heat-insulating property of the silica aerosol and to furnish its production method. SOLUTION: A protective coating film of transparent resin is formed on the whole or a part...

PROBLEM TO BE SOLVED: To prevent surging of a compressor generated when an air capacity is reduced in the case where a load is reduced, in a compressor surging preventing device for pressure fluidized bed combined power generational system. SOLUTION: Combustion gas is supplied from a pressure fluidized bed boiler 13 into a gas turbine 11 through ducts 16, 17, the gas turbine 11 is driven, exhaust ...

PROBLEM TO BE SOLVED: To effectively cool the high temperature section of a gas turbine and hence to use material with reduced heat-resistant performance for the high temperature section of the gas turbine to reduce cost by supplying the high pressure steam turbine exhaust cooled by gas turbine fuel to the high temperature section of the gas turbine as cooling steam. SOLUTION: When a gas turbine p...

PROBLEM TO BE SOLVED: To achieve a higher heat efficiency by a method wherein water is extracted at an intermediate point or an outlet of an economizer of a waste heat recovery boiler, utilized to cool a device to be cooled in equipment and the extracted water after the cooling is recovered into the waste heat recovery boiler to prevent low temperature corrosion. SOLUTION: In cooling water for a h...

PROBLEM TO BE SOLVED: To provide a hot water feeder capable of attaining a small volume of heat accumulating type hot water storing tank, and further capable of being installed even in a small space in a less-expensive manner. SOLUTION: There are provided a solar heat collecting device 1, a heat exchanger 2 for performing a heat exchanging operation under utilization of solar heat collected by the...

PROBLEM TO BE SOLVED: To increase a customer's degree of satisfaction in utilization of a solar heat hot water heater utilizing solar heat and then improve an efficiency of its utilization. SOLUTION: A water feeding pipe 18 for feeding water to a hot water storing tank 12 and a bypass pipe 19 not bypassing the hot water storing tank 12 are branched as water feeding means for the hot water storing ...

PROBLEM TO BE SOLVED: To provide a sack-shaped separator which can heighten the energy density of a battery in proportion to the volume of a battery jar. SOLUTION: One sheet as material for separator is folded into halves in such a shape as enwrapping an electrode plate 2, and two separator members 3 and 4 located on the sides of the folded part are joined together so that a sack-shaped separator ...

PROBLEM TO BE SOLVED: To enable a detector to transmit information on spectra, by composing each of a specific number of parallel detector arrays by detecting element arrays and making an X-ray beam to collide with at least one of the detector raw filtered by a beam filter. SOLUTION: A first beam diaphragm of an X-ray beam 2 is set in the vicinity of a focal point 11. A detector 3 comprises two pa...

PROBLEM TO BE SOLVED: To reduce road noise without altering tire shape and structure and without largely increasing a manufacturing cost by vulcanization molding a region near a bead of a green tire while sandwiching it by dividable auxiliary molds from a tire inside. SOLUTION: A pair of struts 5 provided at an equal interval in a circumferential direction of a vulcanization central shaft 4 rotata...

PCT No. PCT/GB93/01259 Sec. 371 Date Feb. 23, 1995 Sec. 102(e) Date Feb. 23, 1995 PCT Filed Jun. 17, 1993 PCT Pub. No. WO94/00278 PCT Pub. Date Jan. 6, 1994An apparatus for shaping perforations of sheet material which comprises a first mold structure at one side of the sheet material and a complementary mold structure at the other side of the sheet material to cooperate with the first mold structu...

Porous pipe formed of particles of vulcanized rubber dispersed in a binder resin such as polyethylene are stabilized to reduce degradation by ultraviolet light by dispersing in the binder resin an effective amount of an ultraviolet stabilizer such as 0.1 to 10% by weight of carbon black.

This invention is a device (10) for exercising facial muscles comprising a pair of spreader bars (13, 14) each spreader bar having fixed at one end thereof a lip-engaging piece (11, 12), and at the other end thereof a coupler (15, 16). Each spreader bar is coupled to a coupler attached to the other spreader bar. Preferred embodiments include curvilinear members (17, 18) for easy attachment of elas...

An eye glass holder is provided which is attachable to an article of fabric, for supporting and securing a pair of eye glasses. The eye glass holder comprises a pin assembly engageable to the fabric. The pin assembly includes a substantially planar member having an outer eye glass frame striking surface and an inner fabric abutting surface. The pin assembly further includes a ring member extending...