PURPOSE:With regard to an automatic change gear, to make it possible to set the kick down change gear point higher when quick acceleration is particularly required and to shift it down to a low level in normal kick down.

PURPOSE:To improve the low steering performance and travel stability by detecting considerable difference of tyre air pressure in each drive wheel when travelling under deflock state thereby releasing the deflock state. CONSTITUTION:Upon turning on of a switch 10 as required, a solenoid 8 is excited by a signal from a control circuit 11 to exchange a valve 5 thus to feed pressurized oil to a diffe...

PURPOSE:To obtain the highest speed by performing accleration with the engine output at the max. value, in sharp acceleration of a car which aims at improvement of fuel consumption. CONSTITUTION:In sharp acceleration where an acceleration pedal 17 is stepped- in sharply, a correction value signal is added into the accelerator stepping-in amount signal supplied from an accelerator position sensor 1...

Fibre rovings are impregnated with liquid at the moment when they are wound on a drum 5 after carding, division and rubbing. The drum 5 comprises apertures 6. A conduit 8 leads liquid axially into the drum and nebulizers 9 disperse the liquid on the inside thereof. The drum 5 is covered on the outside with a layer of absorbent material to distribute the liquid.

L'ELECTRO-AIMANT COMPORTE UN CIRCUIT MAGNETIQUE FERME, AYANT UNE FORME DE REVOLUTION, CONSTITUE PAR UN STATOR 51 ET PAR UNE ARMATURE MOBILE 54. UN ENROULEMENT 53 SERT AU PASSAGE DU COURANT D'EXCITATION.

LA PARTIE DU CIRCUIT MAGNETIQUE ENTOUREE PAR L'ENROULEMENT 53 EST TUBULAIRE ET COMPORTE UNE PAROI MINCE. L'INDUCTION MAXIMUM, OBTENUE LORSQUE L'ELECTRO-AIMANT EST EXCITE, NE DEPASSE QUE LE...

PROCEDE DE FUSION METALLURGIQUE, SUIVANT LEQUEL ON PROVOQUE UNE DECHARGE ELECTRIQUE ENTRE DEUX ELECTRODES ALIMENTEES EN COURANT CONTINU, SOUS DEUX POLARITES OPPOSEES, CARACTERISE EN CE QUE DANS UNE PREMIERE PHASE, OU PHASE DE DEMARRAGE, ON UTILISE COMME ELECTRODES, DEUX ELECTRODES DE VOUTE 8, 9 AMENEES AU VOISINAGE DE LA SURFACE DE LA MASSE METALLIQUE A FONDRE 2 QUE L'ON FAIT PENETRER PROGRESSI...

PURPOSE:To provide a solid fuel having a high calorific value, generating only a small amount of smoke and exhibiting excellent ignitability, prepared by adding diatomaceous earth, soda ash, a specified adsorbent, a smoking inhibitor and a combustion promoter to peat. CONSTITUTION:A naphthenic acid-based metal salt (e.g. cobalt naphthenate) as smoking inhibitor, a diphenyl carbonyl type metal comp...

A process for afterburning and purifying process exhaust gases, which contain combustible constituents, wherein the process exhaust gases and the oxygen-containing gases required for a combustion are separately supplied to a fluidized bed reactor of a circulating fluidized bed. In the fluidized bed reactor, the gas velocity is adjusted to 2 to 10 m/s (empty pipe velocity), the mean suspension dens...

A method and apparatus for effecting vital functions notwithstanding the fact that non-vital hardware is employed. A vital processor is implemented using non-vital hardware in the form of a digital computer which may for example be a microprocessor. The vital processor accepts binary input values and, based on a series of logical expressions relating output values to input values, determines the a...

As a component in a vital processing system, the vital driver includes hardware and software elements that enable it to produce a time sensitive output in response to receipt, on a batch basis, of check words. The number, content and rate of the check words are checked and used by the vital driver to produce a time sensitive output which can have parameters such as carrier frequency, modulation ra...

The present invention provides an apparatus for continuously coating aligned cords having knots or other enlarged irregularities therein. A cord-alignment baffle means of novel construction located at the cord entrance of an extrusion coating die assembly enables passage of splices such as knots. The baffle means comprises a plurality of cord-alignment apertures, each of which comprises a guide po...

PETIT FILTRE A GAZ DANS LEQUEL LA MEMBRANE FILTRANTE HYDROPHOBE EST COINCEE ENTRE DEUX PARTIES DE BOITE EN MATIERE PLASTIQUE.

LES ESPACES LIBRES DU SUPPORT DE FILTRE 31 INFERIEUR SONT FORMES PAR UN CANAL ANNULAIRE 33 ET AU MOINS UN CANAL DE LIAISON 32 AVEC LE CANAL COLLECTEUR 27. LE CANAL DE LIAISON 32 VA EN S'ELARGISSANT DU CANAL COLLECTEUR 27 AU CANAL ANNULAIRE 33. SON FOND SITUE EN DES...

L'INVENTION CONCERNE UNE MOUSSE DE POLYURETHANE FLEXIBLE.

SELON L'INVENTION, CETTE MOUSSE SENSIBLEMENT EXEMPTE DE CHARGES A UNE DENSITE DE MOINS DE 90KGM, UN MODULE D'ELASTICITE DE MOINS DE 10NM ET UN FACTEUR DE PERTE D'AU MOINS 0,3 AINSI QUE DES PROPRIETES VISCOELASTIQUES DANS LA PLAGE DE TEMPERATURE DE (-20 A 80C); LE DESSIN JOINT MONTRE UNE COMPARAISON DU DEGRE D'ABSORPTION SONIQUE DE ...

Stable dispersions of halogen-containing addition polymers, such as polyvinylidene fluoride, in water-dilutable liquid media, for example 2-butoxyethanol, are produced by dispersing pre-formed particles of the polymer, of a number-average size in the range 0.1-10 microns, in the liquid medium in the presence of a polymeric dispersant containing in the molecule a hydrophobic polymer chain and stron...

A fast molding foamable composition comprising a terpolymer of ethylene, 10 to 40 percent by weight of a softening monomer and 1.0 to 20 percent by weight carbon monoxide, a free radical crosslinking agent and a chemical blowing agent.

An electromagnetic brake wherein a magnetizable armature is fixed to a rotary shaft in a motor or machine and a casing for a solenoid and a permanent magnet is non-rotatably fixed to a stationary member of the motor or machine with freedom of movement in the axial direction of the armature. When the solenoid is deenergized, the magnet maintains a friction liner in the casing in frictional engageme...

A measuring device for a seismic profile within a well-bore includes resilient members such as springs which are flexible in at least two directions and are interposed between a geophone and a rigid arm connected to a measuring-tool body for applying the geophone against the wall of the well-bore during each detection of seismic waves generated at the ground surface. The elasticity of the resilien...

The invention relates to a reciprocating driving device for a movable member such as a movable hair shearing blade assembly in reciprocal type electrical shaver. A reciprocally driven mounting member is coupled to an eccentric shaft of a motor and comprises a carrier which carries the movable blade. Resilient legs support the plate part for movement only in the direction of reciprocation and are f...