PURPOSE: To enable the use of a flat drum so that a fold does not appear in a layer forming the carcass in the vicinity of a bead ring at the time of use of a planing strip made of almost square reticulated fibers placed in rubber in a layered form. CONSTITUTION: A building drum is equipped with lock parts expansible in a radial direction constituted so that the carcass layer 10 placed on the buil...

PURPOSE:To prevent lowering of driving performance even when both drive wheels are in a slipping state and realize vehicle behavior sufficiently reflecting an intention of a driver. CONSTITUTION:Wheel speed sensors (NFL sensor, NFR sensor, DRL sensor, DRR sensor) are read in (S21) and an outer wheel and an inner wheel at the time of vehicle turning are discriminated (S22) based on these wheel spee...

PURPOSE:To provide an intake air flow control device for an internal combustion engine with an automatic transmission to perform slip control during deceleration, by which better fuel consumption is achieved in combination with a ISCV throttle control. CONSTITUTION:If slip control is not performed (YSLUEX=0) when a speed is 5km/h or faster under warm-up condition, a shift position is in another ra...

PURPOSE:To provide a braking device which promptly determines the braking mode of an auxiliary brake in accordance with the braking operation speed of a main brake and performs correct auxiliary braking from the beginning. CONSTITUTION:A brake pedal operating speed is detected (S4), and if it is within a preset range (S8) shiftdown is usually performed from the fourth gear position to the third ge...

PURPOSE:To suppress impact generated at the time of switching to a service brake from a regenerative brake, and secure fail safe also at the operating time of the regenerative brake. CONSTITUTION:A regenerative braking device for a vehicle is provided with a brake valve 2 for generating braking pressure according to the depression quantity of a brake pedal 1; a pressure reducing valve 76 interpose...

PURPOSE:To improve expression of tastiness on opening of a package wherein food is contained, to stimulate therewith one's appetite and to make the food contained eatable satisfactorily. CONSTITUTION:A rice cracker 1 is put in a bag 2 and the bag is sealed up. In a case as shown in the drawing, the bag is made in a pillow type packaging. Therefore, a center sealing 2a, extending in the longitudina...

PURPOSE:To stabilize the stream by bifurcating a condensate pipe line from a steam turbine, by providing a fed water heater and an economizer, by controlling the flow rate on the fed water heater side in accordance with a flow rate of condensate into an deaerator and a water level in the deaerator, and by controlling the flow rate of condensate on the economizer side in accordance with a temperatu...

This disclosure relates to a novel class of hydroxamic acid based collagenase inhibitor derivatives. The disclosure further relates to pharmaceutical compositions containing such compounds and to the use of such compounds and compositions in the treatment of collagenase induced diseases.

A dental floss holder is in the form of a box with a drawer in it. The bottom of the drawer includes a hub which is spring biased to push a bobbin mounted thereon toward an opposite side of the box. The bias is such that the bobbin drags with a predetermined force on an opposite side of the box to maintain tension in the floss. A result is that the bobbin does not unwind while in the holder, there...

PCT No. PCT/FR91/00291 Sec. 371 Date Oct. 27, 1992 Sec. 102(e) Date Oct. 27, 1992 PCT Filed Apr. 10, 1991 PCT Pub. No. WO91/16868 PCT Pub. Date Nov. 14, 1991.Liquid is enclosed in a resiliently deformable container, the neck of which has a microfiltering membrane which is permeable to the liquid but impermeable to air when wet. Since the container resiliently recovers its shape after it is deforme...

A fluid dispensing system for delivering sterile preservative free solution is disclosed. The system uses double self-sealing valves mounted in series inside a tip compartment which fits on the outlet of a multiple dosage squeeze container to prevent undesirable retrograde flow of the dispensed liquid back into the bottle during the decompression cycle. The valves used are positive acting, normall...

The safety binding has a base part which is fixed with respect to the ski, a release part which is supported so as to be rotatable relative to the base part, and a guide jaw with clamping device for clamping the boot sole. In order to support the release part relative to the base part, this release part has at least three guide rolls which are supported so as to be freely rotatable and have circum...

A method for monitoring the coating weight, uniformity, defects or markings present in a coating of a composition applied to a substrate comprises the steps: a) providing a substrate with a functional coating of a composition comprising an effective amount of uvescer that absorbs radiant energy, i.e., has an excitation energy, of wavelength lambda 1 and emits radiant energy of wavelength lambda ...

Detection of a defect (18) on the surface (15) of an article (10), such as a semiconductor chip, is accomplished by illuminating the chip in a bright field and then capturing the image thereof with a television camera (30) coupled to a machine vision processor (32). To detect the defect (18), the vision processor first adaptively thresholds the captured image to effectively eliminate areas in the ...

PCT No. PCT/DK92/00329 Sec. 371 Date May 2, 1994 Sec. 102(e) Date May 2, 1994 PCT Filed Nov. 10, 1992 PCT Pub. No. WO93/09753 PCT Pub. Date May 27, 1993.A container for receiving and separating blood plasma into its ingredients comprises two sealingly coupled sections (1 and 2). One container section (2) and the adjacent portion of the other container section are made of solid material, and the tw...

PCT No. PCT/DK92/00329 Sec. 371 Date May 2, 1994 Sec. 102(e) Date May 2, 1994 PCT Filed Nov. 10, 1992 PCT Pub. No. WO93/09753 PCT Pub. Date May 27, 1993.A container for receiving and separating blood plasma into its ingredients comprises two sealingly coupled sections (1 and 2). One container section (2) and the adjacent portion of the other container section are made of solid material, and the tw...

PURPOSE:To provide aesthetically excellent dental materials which resist corrosion and discoloring and are not conspicuous and broken by surface treating conventional alloys. CONSTITUTION:A dental bracket and a dental steel wire 1 which serve as dental materials use stainless steel 2. The surface of the stainless steel is plated with three layers of single metals comprising silver 3, platinum 4 an...

PURPOSE:To manufacture a filter element in a lessened number of processes and materials wherein the filter element is formed into a hollow cylindrical shape and the center part of a circumferential wall of the cylinder in the thickness direction is composed of fibers thinner than the fibers used for the both sides of the center part. CONSTITUTION:After a strip of a first fibrous body 41 is coiled ...

PURPOSE:To obtain nonwoven fabric having excellent liquid permeability, feeling, flexibility and dimensional stability by thermally adhering thermoplastic resin to form a fiber bundled part, placing the fabric on a perforated support, and opening pores by high speed fluid. CONSTITUTION:A fiber bundled part 1a having a point adhered part 1c and pores 1b in which fibers are twisted and sorted are pr...

PCT No. PCT/DK92/00329 Sec. 371 Date May 2, 1994 Sec. 102(e) Date May 2, 1994 PCT Filed Nov. 10, 1992 PCT Pub. No. WO93/09753 PCT Pub. Date May 27, 1993.A container for receiving and separating blood plasma into its ingredients comprises two sealingly coupled sections (1 and 2). One container section (2) and the adjacent portion of the other container section are made of solid material, and the tw...