"Improvements Relating to the Manufacture of Tobacco Smoke Filters" A particulate plastics material, a polysaccharide and water are fed to an extruder which is operated under such heat and pressure conditions that upon emergence of the extrudate from the extruder die, the extrudate assumes a cross-section greater than that of the exit orifice of the die.

2095215 9211829 PCTABS00014 A method for applying loops formed from a supply length of elongate strip material in spaced relationship along a substrate. Lengths are cut from the supply length, and have their ends supported on peripheral surfaces of two circular disks mounted with their axes oriented to position portions of the peripheral surfaces of the disks on which the lengths are positioned at...

PURPOSE:To permit inexpensive and easy degradation of oil-contg. water sludge by adding granular quicklime and surfactant to the oil-contg. water sludge, kneading the sludge and subjecting the sludge to drying in the sun, thereby reducing and degrading the sludge. CONSTITUTION:The granular or lump quicklime, >=50wt.% of which consists of 1-20mm grain size, is added at 1-55wt.% and the surfactant (...

PURPOSE:To restrain generation of unevenness of color on display by positioning glass substrates in the state where a curved surface is molded and fixed, and positioning a pattern of an electrode on the basis of the position to position the glass substrates. CONSTITUTION:Glass substrates are fixed with cellophane tape as in the state where two pieces of curved glass substrates are moulded. Thereaf...

PURPOSE:To suppress thermal diffusion of the components between layers, to increase the luminous brightness of the element, to improve a voltage-resisting property, and to realize a long service life and a low cost, by maintaining the temperature of a substrate at 150 to 200 deg.C, and forming the layers by an ion beam spattering. CONSTITUTION:After a soda glass substrate 1 is cleaned and dried, i...

PURPOSE:To improve the drawing out efficiency to the outside and the luminous brightness observed from the outside by providing micro condenser lenses on the side drawing out the light generated by a luminous layer. CONSTITUTION:By applying voltage to a transparent electrode 3 and a back electrode 7, a luminous layer 5 held between insulating membranes 4 and 6 is made to emit the light. And at the...

PURPOSE:To suppress a deterioration due to the moisture in a phosphor and to extend the service life by mixing a specific amount of inorganic moisture absorbent to one side or both of a phosphor layer and an insulator layer. CONSTITUTION:As an inorganic moisture absorbent, a white or transparent substance with the particle diameter 5 to 10mum is used, and it is selected from zeolite, a silica gel,...

- Devices and processes for correcting and monitoring the position of an automotive machine. - The invention relates to a device for correcting an automotive machine propelled by at least two hydraulic motors (3), characterised in that the means of control of the steerable member comprises a hydraulic circuit (10) associated with each hydraulic motor (3) and a leak-off valve (17) which is installe...

To produce a cellulosic article, a cellulosic amine oxide solution is pressed through a nozzle or through a slit, then passed through an air slit and finally coagulated in a precipitation bath. According to the invention, it is not stretched in the air gap, i.e. the ratio of discharge rate to hole emergence rate is at most 1; only the coagulated cellulose is stretched or deep-drawn.

PURPOSE:To obtain a member, of which lowering of critical current density is small even at a liquid nitrogen temperature, by forming no-superconductive phase in dispersion under the specified condition. CONSTITUTION:No superconductive phase parts caused by radiation of energy beam and having a diameter less than 3mum are arranged in dispersion at spaces less than 10mum to form an oxide superconduc...

PURPOSE:To reduce the number of element wires for arrangement at a time to facilitate the aligning, arrangement and make the aligning arrangement of the element wires tight at the time of their insertion into a metal pipe serving as a stabilizing member by dividing multiple superconductive hexagon element wires into multiple units, and arranging the element wires per each unit. CONSTITUTION:Multip...

PURPOSE:To manufacture ceramics superconductor efficiently while preventing generation of void, by performing plastic work to a compound billet, which is obtained by filling the required base material for a superconductor in a metal sheath, so as to form the billet into a desired form, and performing heat treatment at a predetermined temperature for a predetermined holding time. CONSTITUTION:The b...

PURPOSE:To obtain a conductive material having a small diameter and a high Jc value by subjecting a wire material made of a precursor, which is obtained by spinning the original raw material for a specified substance, to heating, temperature rise, temperature, holding and temperature drop, etc., under specific environment to convert the phase and seal the fault. CONSTITUTION:Included organic mater...

PURPOSE:To obtain an effective pinning point, and obtain a high critical temperature and a critical current density by converting the original raw material or the phase, which is generated during burning, to another superconductive phase finally by heat treatment, and allowing various grid fault and fine deposition, which are generated at the time of converting the phase to emerge evenly across th...

PURPOSE:To improve critical current density remarkably by adding the specified organic acid and the spinning auxiliary of the specified spinning agent to acetate oxide of the structural metal of a specified superconductor of oxide, to obtain aqueous solution, and spinning the spinning raw liquid, obtained by condensing this aqueous solution, and performing required pretreatment and burning or the ...

PURPOSE:To obtain a superconductive wire, which is hard to be broken during processing and which has a high critical current characteristic, by holding a material at a predetermined temperature through the whole work process for making diameter reduction processing after performing hot hydrostatic pressure compression processing to a compound billet at the time of manufacturing a superconductive w...

A casing for holding electronic components and the like, is provided on each of its side walls facing away from one another with two fastening lugs which project laterally therefrom and are each provided with an opening for the passage of a screw, and which are associated with casing side edges corresponding to one another. The openings for the passage of a screw which are provided in fastening lu...

This device includes a detection nozzle 6 connected by means of a flexible hose 7 to an electropneumatic feeler 8 communicating to an electronic assembly 9 the digital data picked up by the detection nozzle 6/electropneumatic feeler 8 on the cutter 12 to be resharpened, the rotation of which is controlled by a stepper motor, this digital data being used to program a machining cycle controlled by s...

The station assigned to the transactions (PTC) comprises entry means (LMC) capable, during a transaction, of entering the data relating to a cheque and to its issuer; means (TPC) for entering the amount of the transaction paid with the said cheque; means (TPC) for transferring the data and the amount thus entered into removable storage means (MEM) whilst the station assigned to the post-stamping o...