PURPOSE:To enable torque distributing ratio of front and rear wheels to be varied by changing over the engaging paths of a front wheel drive shaft and a rear wheel drive shaft in a four wheel drive car. CONSTITUTION:A carrier 1 is provided with an input section 2 for receiving the rotation of an engine through a clutch, transmission, etc. Respective spline portions A, B, C, D of a carrier ring 3, ...

PURPOSE:To realize a recording medium superior in flatness and durability by curving a substrate previously so as to cancel the deformation of the substrate due to the internal stress of an optical recording layer. CONSTITUTION:Substrates 1 and 2 where optical recording layers 5 and 6 are formed are concaved enough to cancel the deformation due to the internal stress of various thin layers formed ...

PURPOSE:To prevent the occurence of transmission shock, by a method wherein, during the time between transmission instruction and the starting of transmission, a torque converter is not brought into a lockup state, but it is brought into a slip control state in that a direct-coupling clutch is slip-coupled. CONSTITUTION:In a lockup type automatic transmission gear, the transmission gear is provide...

PURPOSE:To improve the active material preserving feature of an electrode plate and the battery performance by passing a paste-filled electrode plate between a pair of upper and lower rotary rollers with different rotating speeds. CONSTITUTION:An electrode plate filled with paste 1 is passed between a pair of upper and lower rotary rollers 3, 3' with different rotating speeds. For example, the rot...

- La présente invention concerne une imprimante, comportant une sortie de feuilles sur laquelle les feuilles imprimées peuvent être déposées sous forme d'une pile, et un dispositif de mesure grâce auquel des champs de mesure imprimés sur la feuille, formant une bande de contrôle d'impression, peuvent être analysés.
- Selon l'invention, dans la sortie de feuilles, est agencé un dispositif ...

PURPOSE:To obtain a transparent conductive film without any pin hole which is uniform in thickness and hard to be deteriorated and excels in transparency. CONSTITUTION:UV hardening masking ink is applied to a substrate and the solvent resistance is increased by UV hardening. An oil film made on a part of the substrate where the masking ink is not applied can be decomposed with oxidation and cleane...

PURPOSE:To prevent distortion of a waveform in operation of power so as to obtain a normal microwave output by interposing a resistance element between a slow-wave circuit unit and a collector electrode, and setting AC resistance within a range of 10-400OMEGA. CONSTITUTION:A slow-wave circuit unit 2 is electrically insulated from a collector electrode 13 of a collector unit 3 by insulators 19 each...

PURPOSE:To provide a method to manufacture a high brightness and high efficiency type thin film EL element including a luminous layer to which a different kind of luminescent center material is added. CONSTITUTION:A different kind of luminescent center material is mixed while being fused or heated so as to be mixed with luminous layer parent body material in an automatic glass mortar. And next, mi...

PURPOSE:To obtain light emission with sufficient brightness from an electroluminescent element even at low drive voltage to keep initial light emitting characteristics even after a long period of storage by containing compounds indicated by specified formulas in a electron hole transport layer when an anode, an organic electron transport layer and a cathode are laminated in the order and formed in...

PURPOSE:To obtain almost as strong brightness even from low-frequency drive as from high frequency drive by interposing a dielectric film holding a luminous layer between electrode when alternate current or bipolar voltage is applied to between a pair of electrodes faced to each other and correspondingly make a thin film luminescent element luminesce. CONSTITUTION:A transparent electrode 2 compose...

PURPOSE:To enhance display quality by letting a thin film consist of a thick paint film based on the knowledge that the replacement of a part of the thin film with a thick paint film permits sensitivity to any defect to be lowered while the stability of an element is accordingly enhanced in an EL element composed of a laminated structure of thin films. CONSTITUTION:A stripe shaped transparent elec...

PURPOSE: To stabilize a long term operation, by composing a device of anode, organic hole injection transfer band and organic electron injection transfer band that are prepared separately, and cathode, and by containing, in the hole injection transfer band, aromatic ingredients which have two condensed aromatic rings coupled to nitrogen atom of tertiary amine. CONSTITUTION: When build up a lumines...

PURPOSE:To properly and quantitatively extract a failure mode which is peculiar to a surface-mounting type electronic component with reference to the deformation of a board when the surface-mounting type electronic component is mounted on the board or after it has been mounted on the board. CONSTITUTION:A surface-mounting type electronic component 1 is mounted on a board 10, a specimen 20 under te...

A cap (1) of a bottle (2) for a medical fluid (3) having a seal stopper (5) at an opening (4). The cap has a projection (8) integrally extending from a cap body (6) of a cap member, Around the base portion of the projection, there is formed a thin-plate portion (9) for bending and removing the projection from the cap body with ease and safety. The thin plate comprises a continuously recessed groov...

A guidance system for an unmanned transporting vehicle which runs along a guide track. The guide track is composed of a belt-shaped light reflective material and laid out on a floor or the like. The unmanned transporting vehicle has two rows of photodetectors longitudinally arranged thereon forwardly of the front wheel. Since the two rows of the photodetectors are spaced apart from each other with...

PURPOSE:To eliminate the wasteful time in inspection and to enhance inspecting accuracy, by controlling an inspection apparatus so as to move the same in a state following the movement of a container. CONSTITUTION:A mirror 32 is stopped at an inspection part during a time when a bottle 10 moves from A to A' at a certain speed and, therefore, the image of the mouth part of the bottle 10 is picked u...

An external bone fixation device for the fixation of a broken joint includes first and second fixation rods (2,3) connected to bone pins (44,45) intended to be introduced into the bone, and an articulating portion (1) joining the two rods. One (2) of the two fixation rods is connected to a sliding block that slides within the housing of the articulating portion (1) upon a cylindrical sliding surfa...