PURPOSE:To enhance the efficiency of protective film stripping-off work at the time of the regeneration of a cut piece by preliminarily applying stickiness preventing treatment to the protective film bonded to the cut piece at the end edge of a plastic panel. CONSTITUTION:In covering a sent-in plastic panel 1 with protective films 2, 2 sent in from the upper and lower directions shown by arrows, s...

PURPOSE:To enable a slip control to be started always in the optimum timing by detecting different operation information of two or more kinds and, when at least two or more of the operation informations satisfy a predetermined control start condition, starting a control of reducing a drive wheel speed. CONSTITUTION:In the case of a vehicle provided with an engine having in an intake pipe 22 a main...

PURPOSE:To enable a slip control to be started always in the optimum timing by controlling a drive wheel so as to start its drive torque control, when drive wheel acceleration is decided to exceed a predetermined value, while correcting it in accordance with car body acceleration. CONSTITUTION:In the case of a vehicle provided with an engine having in an intake pipe 22 a main throttle valve 23 ope...

PURPOSE:To improve acceleration of a vehicle while surely preventing generation of a slip by detecting different operational information of two or more kinds and, when at least two or more of the operational informations satisfy a predetermined control start condition, ending a control of reducing a drive wheel speed. CONSTITUTION:In the case of a vehicle provided with an engine having in an intak...

PURPOSE:To easily operate a braking mechanism with a speed change pedal utilized by providing an interlocking mechanism or the like operating the braking mechanism to be released from braking by an initial-movement control of the speed change pedal while to be actuated to a braking side by releasing the speed change pedal from the control. CONSTITUTION:An interlocking mechanism 5, which releases a...

Flexible foam is prepared using 1,1,1-trichloroethane as the sole or predominant auxiliary blowing agent.

PURPOSE:To prevent a filler from being damaged with a bead wire under a driving pressure by interposing a cushion material between the bead wire and a rim side end portion of the filler where the bead wire is disposed. CONSTITUTION:The carcass 1 of a tire 1 is covered with a rubber layer 3. A filler 5 is disposed in the carcass 2 of the tire bead section which is the portion to be attached to a ri...

PURPOSE:To obtain a good yield of a lower aliphatic hydrocarbon at high selectivity by catalytic cracking of a hydrocarbon composed mainly of specified medium paraffins in the presence of a specified catalyst. CONSTITUTION:When a lower aliphatic hydrocarbon composed mainly of a 3-4C paraffin is produced by catalytic cracking of either a 5-10C paraffin or a hydrocarbon composed mainly of these para...

PURPOSE:To continuously produce a lower aliphatic hydrocarbon in a high yield by a fluidized bed system for catalytic cracking of a hydrocarbon composed mainly of specified medium paraffins in the presence of a specified catalyst. CONSTITUTION:When a lower aliphatic hydrocarbon composed mainly of a 3-4C paraffin is produced by catalytic cracking of either a 5-10C paraffin or a hydrocarbon composed...

PURPOSE:To make it possible for even a factory having no LNG storage tank to receive LNG through a pipeline and mix it with a manufactured gas to produce a 13A gas for stable supply in compliance with the change in demand by incorporating LPG into a reformed gas obtained from a petroleum-base hydrocarbon to give a manufactured gas having a calorific value equal to that of LNG and mixing LNG with t...

PURPOSE:To simplify a manufacturing process by a method wherein, after a spray coating film is formed on a substrate by spraying green chemical composition material and the substrate is heated at a temperature higher than or equal to the temperature at which the chemical composition is sintered, the substrate is gradually cooled. CONSTITUTION:A desired spray coating film 5 is formed on a substrate...

PURPOSE:To contrive the reduction of control force by confronting with a balance lever an intermediate control lever receiving control force of a control lever and an assist lever receiving acting force of an actuator and transmitting a motion of the balance lever to a parking brake means through an acting lever. CONSTITUTION:To apply a parking brake, when a stick lever 1 is pulled up by control f...

PURPOSE:To contrive the reduction of control force by constituting a device applying the control force of a stick-type control lever and acting force of an actuator to an assist lever and transmitting its motion to a parking brake means through an acting lever. CONSTITUTION:For applying a parking brake, when a stick lever 1 is lifted, control force (f) is applied to a balance lever 14 in its conne...

The residual metal content of tightly chelated heavy metal-containing effluents is reduced by carrying out a sulfide precipitation process in the presence of a seed material comprising an added unchelated soluble heavy metal salt, preferably with an adjustment of pH to at least above about 9.0, with optional variations including passage through a mixed filter media comprising at least two particul...

The process of forming a laminate by molding, preferably either by compression or injection molding, a polymer which is incompatible with PVF2 onto the surface of a preformed laminate sheet of a PVF2 and a polyalkyl methacrylate, with the preformed laminate have been previously obtained by the coextrusion of the PVF2 and polyalkyl methacrylate.

To produce molten pig iron by melt-reduction of iron ores of various grain sizes containing a fraction A including grain sizes to which diameters of less than 0.2 mm correspond, by pre-reducing the ore by reducing gas, completely reducing the pre-reduced material and smelting it to molten pig iron in a melter gasifier, the pre-reduced ore fraction A is separated from a fraction B including larger ...

A stoppered drug vial forms part of a drug delivery system which maintains the sterility of the drug in storage, dilution and use. A removable, pierceable diaphragram is placed over the stopper which seals the vial. The removable, pierceable diaphragm is held in place by attachment to a skirt member which encloses and is in frictional contact with the upper portion of the vial wall. Access to the ...

PURPOSE: To transfer a message by a message exchange protocol and an exchange protocol by allowing at least one of plural exchange faces for transfer data among plural processors to control data transfer passing the exchange face itself and data transfer passing other exchange faces. CONSTITUTION: Each link pair 40 is connected to one of exchange faces 32 or a control/data face 34 is a switchboard...

PCT No. PCT/GB85/00097 Sec. 371 Date Nov. 4, 1985 Sec. 102(e) Date Nov. 4, 1985 PCT Filed Mar. 8, 1985 PCT Pub. No. WO85/04132 PCT Pub. Date Sep. 26, 1985.The invention relates to a method for bonding a mirror to a substantially rigid backing board using a solvent-based adhesive with solvent vapors being removed through a porous layer between the mirror and the backing. Apparatus for carrying out ...