PURPOSE:To perform the appropriate control of fastening force by disposing a sensor for detecting the displacement of an operating arm between the operat ing arm and a detecting arm fired on the operating arm, thus detecting the deflection quantity of the operating arm without being influenced by the abra sion and the like of a member. CONSTITUTION:At a fulcrum shaft 55, a detecting arm 63 is inte...

PURPOSE:To enable the correct control of differential limiting force without being influenced by the abrasion coefficient change and the like of a clutch disc by detecting the relative displacement quantity between a plate holder and a differential case variable according to the actual fastening quantity of a friction clutch. CONSTITUTION:A rotational position sensor 67 for detecting the relative ...

PURPOSE:To promote the success rate of yarn-stretching by holding a yarn rapidly for sure by means of a yarn-stretching means provided on an end of an empty bobbin and keeping the length of the yarn constant between the yarn- stretching means and a cutter. CONSTITUTION:When a shaft 35 is driven clockwise, a roller chain 33 in a square pipe 34 is driven via a sprocket 36, and a yarn Y6 running betw...

PURPOSE:To contrive a compactness of a machine and to reduce oil leackage by eliminating an outer seal, by providing a governor in a space inside a converter housing, in a captioned automatic speed change machine of a FF type motor car. CONSTITUTION:An automatic speed change machine of a FF type motor car is provided with a torque converter 1 cum direct coupled type clutch which is connected with ...

The yarn pieces to be joined are stretched between the two pairs of suction tubes (28, 29; 30, 31) and untwisted by being wound about spindles (20, 21). Hot compressed air fed along the surface of two blocks (32, 33) adjacent to the untwisted yarn portions remove free fibers and distribute the fiber tufts in the base of a channel formed in said blocks (32, 33). Said tufts are retained in the base ...

PURPOSE:To assure necessary capacity and to suppress self-discharge of positive plate by forming a film made of water soluble macromolecule on the surface of outer frame of positive plate substrate thereby suppressing sulfric acid concentration in the vicinity of substrate. CONSTITUTION:A film composed of water soluble macromolecule is formed on the surface of outer frame of positive pole substrat...

Combined cycle for producing energy from coal, consisting of an MHD converter supplied with the plasma generated with the gas obtained from an allothermic coal gasifier with water vapour, supported thermally by the converter exhaust gases, followed by a Rankine steam production cycle which uses the thermal content available in the converter exhaust gases after the exchange with the gasifier.

The invention provides a method of moulding a plastics material comprising the steps of placing the material with a quantity of an appropriate catalyst in granular (including powdered) form into a hollow mould shell (1); suspending the mould in a mounting system enabling rotation in a plurality of directions whereby the powdered material, together with the catalyst, is able to flow over all the in...

1. Suction device usable on at least one level (1) of a building, of the type comprising a suction tube (6) held in the hand and connected by a flexible tube (7) to a suction duct (8) connected itself to a centralized suction collector (2), characterized in that at least the suction duct (8) can be wound up preferably automatically on a movable winding device mounted on a vehicle (5) and driven by...

For the treatment of the surface of paraffin bodies (30) used for the paraffining of yarns, there is provided a device which holds the paraffin body (30) in a receptacle (10) and which is assigned means (20) for processing the surface of the paraffin body (30).

In known centrifuges for continuously separating materials of different densities, nozzles for the discharge of the dense material are arranged on the drum shell in the discharge area of the dense material, which nozzles are operatively connected to an adjusting device located outside the centrifuge drum by adjusting members arranged inside the centrifuge drum. The nozzle openings are here opened ...

In the four-wheel-drive motor vehicle of transversely-disposed type, a front differential and a center differential are arranged coaxially on the axle line of front wheels, and an engine and a transmission are disposed transversely to the vehicle body in the rear of these differentials. This arrangement can relieve one-sided action of the vehicle body weight on the front wheels.

Below the cover, pref. pivotable, of a cuboid container is a pan for holding pre-cut pieces of meat, intended for mince prodn., at a safe storage temp., e.g. 4 deg.C. From the floor of this pan, meat pieces are taken by a vertical feed worm to enter the horizontal cavity of a standard mincing machine expelling the mince from the container side-wall. Side walls and floors in the compartmented conta...

A method for removing suspended particles from a liquid by means of gas-bubble flotation, in which, before the gas-bubble flotation step proper, the liquid is more or less saturated with the gas in one or more preceding gas introduction steps, so as to obtain a longer average life-time of the smaller gas bubbles in the final flotation step.

A packaging machine for forming a web of packaging material into a vertical tube, filling contents into the tube (T), dividing the tube into lengths each corresponding to one container and forming each length into a baglike container. The machine comprises a filling device (22) for filling a liquid into the tube (T) to a specified level with the lower end of the tube (T) closed, and a cleaning dev...

The present invention relates to foamable thermosetting polyurethane structural adhesive composites and compositions and processes for producing the same comprising dispersing a water-generating curing composition into a polyurethane base resin to form a nonactivated adhesive composite, and activating the same by heating to form an adhesive composition. Another aspect of the invention relates to d...

The present invention relates to foamable thermosetting polyurethane structural adhesive composites and compositions and processes for producing the same comprising dispersing a water-generating curing composition into a polyurethane base resin to form a nonactivated adhesive composite, and activating the same by heating to form an adhesive composition. Another aspect of the invention relates to d...