PURPOSE:To make it possible to reduce resistance of rotation, by setting a clutch means adapted to connect/disconnect the rotary motion between a case part on differential gears built-up body side and a case part on ring gear side, and disconnecting this clutch at a change to two-wheel drive. CONSTITUTION:A case part 32 on differential gears built-up body side can rotate on axles 10, 12, and suppo...

PURPOSE:To improve the traveling performance and operation performance in the four wheel drive by ON-operating a four wheel drive sensor and locking a differential gear in interlocking with the ON-operation, in the switching to the four wheel drive. CONSTITUTION:When switching to the four wheel drive side is performed by operating a switch not shown on the figure, a shaft part 44 shifts to the fou...

PURPOSE:To facilitate the drive on a stagnant road by reading out the previously memorized pseudo acceleration value according to the between-vehicle distance and the car speed detected by a car speed sensor and carrying out the throttle valve control or automatic brake control, when the stagnant road traveling state is detected. CONSTITUTION:During the operation of a vehicle, a controller 20 judg...

PURPOSE:To reduce the high torque or the high-frequency torsion stress and to increase the strength of the shaft member by heating and cooling the torque transmission point on the outer surface of the power-transmission shaft member or its periphery of an oil hole crossing the member while torquing the point, removing the torque, and then imparting a residual stress. CONSTITUTION:The following res...

A method of reducing image artifacts in tomographic, projection imaging systems due to periodic motion of the object being imaged includes the acquisition of a signal indicative of the periodic motion. This signal is used to identify a quiescent period in the periodic motion so that the acquisition of projection data may be coordinated to be centered within the quiescent period. The sequence of th...

A method of preparing ribbed ticks comprising a textile top sheet (60) and a textile bottom sheet (61) and partition-wall strips (1), said strips being welded along their opposite side edges to the top sheet and bottom sheet, respectively, by heating the entire surface of the joined webs of textile material after placing of lengths of folded partition-wall strips (1) in a given pattern, said strip...

A ratio control system for a continuously variable transmission performs a feedback control wherein an integral control gain and a proportional control gain are varied depending upon the level of a line pressure that is used to actuate a pulley unit during shifting operation.

A rear suspension system comprising a rear differential gear mechanism for transmitting a driving force to rear wheels through rear axles, a suspension support member for supporting the rear differential gear mechanism, a pair of front lateral links extending horizontally and transversely, and a pair of rear lateral links extending horizontally and transversely at rear positions of the front later...

Method of purification of aqueous glyoxal solutions which contain organic acids by means of a membrane cell consisting of at least two chambers, in which the glyoxal solution is passed through at least one of the chambers of the cells, which is separated from the adjacent chamber(s) by an anion exchanger cell and where the aqueous solution of a base is passed through at least one of the adjacent c...

A splicing device for splicing the tow ends of synthetic-fibre tows has a pair of nozzle carriers (17) with pairs of nozzles (18) directly in opposition. These can be loaded with compressed air, the connection of the tow ends brought between the pair of nozzle carriers (17) being made by aerodynamic swirling. In order to allow an automatic splicing operation, the pair of nozzle carriers (17) is ar...

Dihaloformaldoximes of the formula: wherein R, X, X1 and Y are as defined herein having biocidal, fungicidal and pesticidal activity are disclosed.

A defect inspection apparatus having a television camera which picks up an object to be inspected and produces a video signal for inspecting defects on the object, wherein the apparatus comprises a detection section which outputs a signal responding to the positive changes of the video signal with respect to time and a further detection section which outputs a signal in response to the negative ch...

A hot tire forming method whereby at least some of the elements constituting each tire are formed starting from respective masterbatches, which are mixed with given chemical compounds inside respective continuous mixers to obtain respective final mixes, which are hot-fed to respective continuous production means, such as extruders, for obtaining semifinished products, which are hot-fed onto a fini...

A biaxially-oriented polymer film having dual-sided appearance, i.e., the color of each side is chromatically different. Also a method for making such films.

Natural rubber latex compounds are modified by the addition of a high styrene content styrene-butadiene copolymer. The films prepared from these modified NR latex compositions exhibit improved tear strength and a good balance of other properties.

An olefinic themoplastic resin compsn. is prepd. by: preparation of a premixture of dispersed crystalline polypropylene in olefinic polymeric rubber which is obtd. by melt-mixing a mixt. comprising 1:0.01-0.5 ratio of olefinic polymeric rubber and crystalline polypropylene; and melt-mixing by mixing-extruding appts. of the mixt 10-75 wt. pts. and crystalline polypropylene 90-25 wt. pts. in presenc...

PURPOSE:To prevent a communication pipe from flexing by external force, by providing a pipe protector so as to hold a protecting part, which covers the communication pipe of an opposed piston type disc brake device, and the communication pipe to be urged in the radial direction of a disc and shielding the radiation of heat from the disc so as to prevent a temperature rise of working fluid in the c...

Natural rubber latex compounds are modified by the addition of a high styrene content styrene-butadiene copolymer. The films prepared from these modified NR latex compositions exhibit improved tear strength and a good balance of other properties.

A hydraulic control system for a continuously variable transmission for an automotive vehicle, the transmission having a first and a second variable-diameter pulley provided on respective first and second shafts, a belt connecting the first and second pulleys, and a first and a second hydraulic cylinder for changing effective diameters of the first and second pulleys. The control system includes a...

In order to correct tooth engagements, the fault in the tooth system and gear wheel attachment acting on the transmission of rotation is overcome with the aid of arc displacements. In this case, the influences of all the participating components must be taken into account and eliminated as far as possible. In order to achieve a reproducible position of the gear wheel on its shaft journal, its posi...