PURPOSE:To get rid of forming ununiform modification on a tire constitutional material by fitting a pair of beads on the outside of specified position of both end parts of the tire constitutional material wound on parts of a molding drum and a side bladder and performing primary lock with an elastic ring provided on a recessed part of a bead support segment. CONSTITUTION:On the inside of a side bl...

Controlled compressed-air splicing device for textile threads with a controlled compressed-air metering valve supplied from a compressed-air supply device, including an automatic quality control device for ensuring the quality of spliced joints formed by the splicing device.

PURPOSE:To cut the surface of new ceramics efficiently by forming numerous recessed streaks on the surface of new ceramics by laser beam in the direction of X axis and cutting thus generated recessed stripes by laser beam from the horizontal direction. CONSTITUTION:A laser head 1 that irradiates laser beam on new ceramics 3 such as alumina, zirconia, silicon carbide, silicon nitride, etc. or on th...

PURPOSE:To smoothen the departure and acceleration of a vehicle by interlocking the clutch and the change gear in the operating device of a traveling power transmitter of working light vehicles, e.g., riding type lawn mower, riding type snow remover or transporter, etc. CONSTITUTION:When an operating lever 2 is actuated along a shift pattern 4, a pinion 6 and a triangular cam 7 integrated with the...

PURPOSE:To reduce speed silently while to reduce projection into cabin, by arranging center def and front def of four-wheel-drive vehicle equipped with a lateral engine coaxially then driving the center def through a chain. CONSTITUTION:Driving force of engine is transmitted through a clutch 5 to the input shaft 6 of transmission 3 then speed changed properly and outputted from a drive sprocket 25...

PURPOSE:To reduce the inner distortion depending on the winding position and the aging of thread quality, by employing specific reciprocation speed and winding speed of spindle in a spindle drive winder where the package under winding is made contactless against others. CONSTITUTION:The winding speed must be higher than 5,000m/min, preferably higher than 5,500m/min, where the thread produced throu...

PURPOSE:To prevent abrasion of a sleeve, by making the sleeve at the inside of a spring plate for pressing a frictional clutch movable in the circumferential direction and employing a smoothly curved face in the border section between the inclined face sleeve and the pushing sideface. CONSTITUTION:A frictional clutch 3 being pressed by a spring plate 2 and a sleeve 6 are provided in a clutch case ...

PURPOSE:To reduce the speed reduction shock by blocking the shift-down control signal, during the decelleration of brake, and controlling the rotation of an engine. CONSTITUTION:Under braking operation, the control of engine speed is stopped at the shift down while the engine speed is controlled for predetermined time at the lock-up control then the engine speed and the torque controller output sp...

A cylindrical yoke of an electromagnet consists of two or more yoke elements, each of which is made of a number of yoke pieces made of magnetizable metal sheets and arranged radially around a cylindrical coil member of the electromagnet and of a filler member unifying the yoke pieces. The thickness of the yoke piece increases with increasing radial distance in order to improve the space factor of ...

PURPOSE:To judge the operation quality of an ending machine using simple apparatus and procedure, by applying a tension higher than the tension of normal operation to a yarn immediately after ending and judging the ending machine to be abnormal when a prescribed frequency of yarn breakages take place by the repetition of the application of the tension. CONSTITUTION:A tension higher than the tensio...

PURPOSE:To efficiently manufacture a vehicular head rest with excellent accuracy of spacing between stays by a method wherein the stays are set in the recessed grooves of a blow molded frame and fixedly fusion-bonded with resin plates. CONSTITUTION:A hollow frame 3 with two lines of recessed grooves 3a is blow- molded and cooled down. After that, the spacing between the recessed grooves are precis...

PURPOSE:To eliminate the feelings of engine braking, by continuing the disengagement of a lock-up clutch even if the temperature of an engine exceeds a predetermined value during a vehicle running in an engaging range, and by engaging the lock-up clutch only when the running mode is shifted from the disengaging range into the engaging range. CONSTITUTION:Even if the temperature Tw of an engine exc...

PURPOSE:To make smooth braking and starting attainable, by fitting an end part of a brake rod into a long hole of a clutch operating system pedal with some play, while installing a spring in position between the pedal and the brake rod and thereby letting weak braking force produce in advance of clutch-off motion. CONSTITUTION:When a pedal 2 is stepped on, a clutch wire 13 is pulled up whereby a r...

The specification discloses a bipolar battery and a method of making intercell connections between adjacent cells thereof including a container (100) having an intercell partition (108) a section (109) of which is thicker than the remainder of the partition (108). The thickened section (109) has an opening (114) therethrough receiving intercell connector links (124), which opening (114) has a mout...

C-4266 G-1182 BIPOLAR BATTERY AND ASSEMBLY METHOD Bipolar battery and method of making intercell connections between adjacent cells involving use of an elastomeric collar on the links joining bipolar electrode halves compressing the collars in an opening between adjacent cell compartments and injecting a sealant about the collar to seal off the opening.

PURPOSE:To prevent air stay from occurrence and to improve press-bonding properties between a bead and a filler and durability of the bead by a method wherein a folded part of an inside cord of the next bead is inserted in a folded part of an outside cord in the shaft direction of the bead through the inner face side of the bead and the folded part of the outside cord of the next bead is inserted ...

PURPOSE:To enable detection of a defect in an internal surface of an electroluminescence EL emission layer on non-destructive conditions by checking a size of an abnormal spot which appears in a potential distribution image near surface thereof with the surface of the emission layer being scanned by an electron beam. CONSTITUTION:When an electron beam EB within a scan electron microscope 20 scans ...

PURPOSE:To detect a fault of an interval timer by setting different values alternately to plural interval timers, then monitoring the corresponding time-up end signals. CONSTITUTION:When either one of interval timers 2 and 3 has a fault, no time- up signal is obtained from the faulty timer. Thus the output of a flip-flop 11 is fixed at a set or reset state and then changed into a DC output. As a r...

1. Moulding material filled with starch for rigid polyurethane foams, characterised in that the starch filler component represents 3 to 40% of the total weight and at least 80% of it consists of gelatinized starch, which is substantially free of particles of a diameter exceeding 3 mm and has a maximum water content of 15% by weight.