PURPOSE:To efficiently perform fault processing, by commonly using one timer counter for monitoring the time of each hierarchy. CONSTITUTION:A timer counter 10 acts as a monitoring time generating section for monitoring the operating condition of hierarchies 1'-2'. Namely, in the course of monitoring the operation in a channel controlling section 7 at the highest rank, control by an access request...

PURPOSE:To make sure loop detection possible, by setting the most suitable loop detecting level of each program level by means of the number of instruction executing steps. CONSTITUTION:In a control memory 11 programs of each level Li of a line control program NCP are stored. An executing program is selected by a control section 16 and instructions are successively fetched by a register 13 and exe...

A brake actuator for a vehicle having air brakes is disclosed in which air pressure is expelled through the actuator upon release of the brakes in order to purge the latter of contaminants. The actuator includes a housing in which a piston reciprocates. Fluid pressure is admitted to the chamber defined between one side of the piston and the corresponding end of the housing in order to urge the l...

PURPOSE:To suppress the influence of frictional heat, generated when a brake is applied, to brake oil, by providing a heat transmission area reduced part, which suppresses the conduction of heat from the point end side to the rear end side, in the point end part of a caliper piston. CONSTITUTION:A recessed groove 17b is provided in the point end part of a caliper piston 17. The sectional area of a...

PURPOSE:To continuously increase a rate of increasing the brake torque of a front brake and obtain the optimum distribution of brake power in front and rear wheels so as to surely prevent a rear wheel lock when a rapid brake is applied, by constituting a device so that the magnification of its power caused by the action of a lever increases as a piston in a front wheel cylinder forwardly moves. CO...

PURPOSE:To shorten the execution time of an instruction having the small number of turning a mask on by recognizing the number to turn the mask on in a vector processor. CONSTITUTION:When mask information indicating whether a conditional instruction is to be executed or not to respective elements and the number of turning the mask on in each vector length are set up in a mask register 28 at the ex...

PURPOSE:To simplify the inputting operation of a parameter as much as possible, by extracting an omitted parameter from a corresponding registeration area and supplementing it when a part of prescribed kinds of parameter is omitted and inputted. CONSTITUTION:In case where parameters p3-p8 of subscribers A-N are the same ones, an attendant inputs the parameters p3-p8 from a typewriter device TYP in...

PURPOSE:To improve the turnaround and throughput of a transaction processing system, by processing each of plural phases as one transaction when processing designated by one command is formed of serialized plural phases having completeness. CONSTITUTION:A data base accesser 2 is used for making retrieval and update of a data base 1. A transaction controlling section 3, when processing desginated b...

PURPOSE:To reduce the number of working sets required in the course of on-line processing and to improve the processing efficiency, by performing processing based on the address of data when the processing of an application program does not process data other than reference. CONSTITUTION:A data communication monitoring section DCMS informs an application program of the address of a DCMS buffer, in...

A cementitious product produced by setting of a composition comprising a mixture of at least one hydraulic cement and water not more than 2% of the total volume of the product comprising pores of maximum dimension exceeding 100 microns and preferably not more than 2% of the total volume comprising pores exceeding 15 microns in maximum dimension, the product preferably having a flexural strength of...

PURPOSE:To shorten the mean instruction executing time, by installing a means which identifies whether a digit designating instruction is direct one or not. CONSTITUTION:When the arithmetic register designating section dr of a register IR is ''1'' and a digit designating instruction is indirect one, addresses outputted from an address converter MAC are started from, for example, an address ''100''...

The title compds. I (R=H, alkyl, alkoxy, halo; m=1-3; n=1-14) were prepd. by the reaction of 2'-deoxy-3'-5'-di-O-alkylcarbonyl-5-fluorouridine(II) with benzonic halide (III). Thus, 2.0g 2'-deoxy-3', 5'-di-o-propionyl-5-uridine in 25mL diocane was reacted with 1.7g 2-methylbenzoyl chloride in 2mL triethylamine at room temp. for 15min and then at 70oC for 30min to give 1.5g 3-(20methylbgenzoyl)-2'di...

A coupling structure for coupling light intelligence between fiber optic elements. Both abuttment and lateral coupling structures are presented.

PURPOSE:To reduce the load of a host computer by forming a page memory enabled to write character patterns, picture patterns and image information as dot images. CONSTITUTION:The titled page printer is provided with a page memory 9 storing character patterns, picture patterns and image information as dot images. A main processor 4 receives and interprets form information sent from the host compute...

A device for transporting a number of articles of clothing placed on hangers (24), between for instance a factory and a place of sale has a suspension member (1) adapted to receive the hooks of the hangers and having a pair of suspension hooks (3) for suspending the suspension member from a rod (23), and carrying means (14) for lifting the suspension member off the rod and shifting it between diff...

A device for transporting a number of articles of clothing placed on hangers (24), between for instance a factory and a place of sale has a suspension member (1) adapted to receive the hooks of the hangers and having a pair of suspension hooks (3) for suspending the suspension member from a rod (23), and carrying means (14) for lifting the suspension member off the rod and shifting it between diff...

1. Method of manufacturing a connector for detachable plug-and-socket connections of optical waveguides, having the following process steps : a) loose insertion of a capillary (2) in a connector cylinder (1), b) acceptance of the capillary (2) between two centering points (19, 20), c) coaxial alignment of an accepting opening (6) of the capillary (2) with the aid of the centering points (19, 20) i...