PURPOSE:To obtain a solar heat collector in which waste heat can be effectively recovered and which has highly convenient operability to eliminate forgetting of water supply to a hot water reservoir 3. CONSTITUTION:A water supply tube 4 for supplying water to a hot water reservoir 3 of a solar heat collector 1, and a sensor 6 for sensing full water in the reservoir 3 are provided. A circulating ci...

PURPOSE:To facilitate liquid injecting work by collectively supplying an equal required amount of electrolyte automatically in respective cell chambers of a storage battery by falling down the storage battery sideways to inject the electrolyte to a collective liquid injecting reservoir thereafter only by raising up this storage battery. CONSTITUTION:A storage battery 1 is toppled sideways to place...

PURPOSE:To obtain excellent electric performance and oxygen absorbing reaction by holding an electrolyte to a fine primary particle of large specific surface area and also generating a clearance by close contact of the aggregated relatively coarse secondary particle to serve as a gas passage. CONSTITUTION:At least 20wt.% red lead relating to lead dust is kneaded with dilute sulfuric acid to produc...

PURPOSE:To improve life characteristic by arranging a synthetic resin foamed body having acid resistance in a part below a plate group, and suppressing that a positive plate extends in an upward direction and short-circuits by contact with a negative pole strap. CONSTITUTION:A synthetic resin foamed body 7, having acid resistance, is arranged in a lower part of a pole plate group. As this resin, f...

PURPOSE:To improve the traveling property of a vehicle, i.e., safety and comfortableness, by synthetically estimating the travel mode of the vehicle, and controlling the vehicle based on it. CONSTITUTION:A travel mode estimating system has multiple sensors including a vehicle speed sensor 8 and an acceleration sensor 14, a memory means 5 storing rules on sensor outputs and multiple partial travel ...

PURPOSE:To prevent a slip and a spin during cornering and improve safety and maneuverability by inputting the handle steering angle and lateral acceleration, calculating the target driving force corresponding to the curvature of a corner, and driving the control subject sections in response to this target. CONSTITUTION:A controller reads the signal alpha from a lateral acceleration sensor 1 and co...

PURPOSE:To prevent an easy lock release and improve safety by restricting the movement of a manual release button at the ignition key position, and allowing the shift lock release via the depression of this button. CONSTITUTION:When the key cylinder 14 of an ignition key is rotated to the on-position, a key lever 15 draws the other end section 16b of a cable 16, the hole 12 of a lock slider 13 is ...

PURPOSE:To precisely judge the travel mode according to the sensibility of a driver by judging it in real time based on the feeling of satisfaction obtained from the membership function set for each travel mode with physical quantities when driving a vehicle used as input variables. CONSTITUTION:The engine data obtained from an E/GECU 4 are inputted to a computer 6 in judging the travel mode, then...

PURPOSE:To cope with an abnormal state by increasing the brake liquid pressure, and decelerating the speed of a vehicle to the preset state when the abnormal state occurs in the driving force control device of the vehicle provided with a driving force device having a throttle valve adjusted with the valve opening to the value corresponding to the depression quantity of an accelerator pedal. CONSTI...

The yarn ballooning action, at a creel, is limited by gps. of paired moving rods (14a, 14b) where the yarns from one row of bobbins are drawn between the rods. The rods (14a, 14b) are given a sliding movement on a parallel plane with each other in relation to the row of bobbins, through a common operating mechanism (24a, 24b, 25a, 25b). Each rod slides on a movement plane about at right angles to ...

PURPOSE:To make the thickness of a silicon layer uniform by locating a single crystal silicon substrate at the place deviated from just below a nozzle and by jetting granular hot melt silicon in the transverse direction from the nozzle. CONSTITUTION:Silicon is melted by application of heat from a first heating source 4. Inactive gases A, B are pressed in through the surface of the hot melt silicon...

PURPOSE:To improve the contrast ratio and to improve the color purity of a black display by effectively performing phase compensation by the compensating cell of the spatial optical modulator. CONSTITUTION:The compensating cell 50 is arranged at an angle to the vertical plane of the optical axis of read light. The surface of a driving cell 50 is slanted similarly. Consequently, read light reflecte...

PURPOSE:To provide a specified gap in a short time by compressively bonding a pair of base boards with the pressure changed over at least in two steps. CONSTITUTION:A glass base board 1, on which a picture element electrode 3 and a thin film transistor 2 for driving liquid crystal are provided in the form of matrix, and another glass base board 4 on which a color filter layer 5 and a common electr...

PURPOSE:To produce uniform gap by permitting a driver circuit protection film to work also for controlling the gap. CONSTITUTION:A pair of base boards equipped with control and drive circuit circuit for the electro-optical effect of liquid crystal are retained by a sealing member 2 provided at the peripheries, and a liquid crystal is encapsulated in the gap 10 in between. Thus a liquid crystal dis...

PURPOSE:To make uniform displaying over the whole panel surface of a liquid crystal display element embodying the simple matrix system, especially in an element in which electric continuity is required from one of the base boards to the other. CONSTITUTION:A spacer 7 is inserted to a seal 6 overlapped on the part where a drawout electrode 9 is formed, while a spacer 13 is inserted in another seal ...

PURPOSE:To reduce the width of the part not contributing to displaying, by overlapping the built-in driver zone on a glass base board and the seal of a liquid crystal panel. CONSTITUTION:A seal 6 does not include glass fiber as a spacer. Therefore, a spacer 8 is provided in the middle part between the driver zone and the picture element region or the opaque part therein so as to determine the gap ...

PURPOSE:To permit complying with demand for many-sort, small quantity production by achieving injection of liquid crystal panel by panel, and to enhance the efficiency of using the material for the liquid crystal. CONSTITUTION:An exfoliatable resin is applied to around the liquid crystal injection hole in a panel 1 so as to provide a simple sump 6 for liquid crystal, and inside of the panel 1 is e...

Installation caractérisée en ce que l'engin mobile (1) comporte également un émetteur infrarouge (11) tandis que l'émetteur portable (8) comporte un récepteur infrarouge (12) correspondant, ces émetteur et récepteur infrarouges étant combinés aux récepteur et émetteur à fréquence radio de façon que, au moins la mise en route de l'engin mobile, ne puisse être effectuée par la télécommande par li...