A control device for a continuously variable transmission performs a feedback control wherein an integral control gain and a proportional control gain of the feedback control are varied depending upon an operating position assumed by a shift actuator.

A ratio control system for a continuously variable transmission performs a feedback control wherein an integral control gain and a proportional control gain are varied depending upon the level of a line pressure that is used to actuate a pulley unit during shifting operation.

A control system for a motor vehicle drive train including a continuously variable transmission is disclosed wherein a command signal is generated in response to the sum of an integral control factor and a proportional control factor, and the integral control factor is suppressed to almost zero when a deviation of a reduction ratio representative parameter from a target value is greater than a pre...

PURPOSE:To vary a distance between chains in accordance with the width of a film that requires variations corresponding to the size of an article to be wrapped, and enable the title machine to be adapted for various sizes of articles to be wrapped by a method wherein a distance between the chains is adjusted by rotating screw bars adapted to adjust a distance between a pair of chains for transferr...

PURPOSE:To eliminate occurrence of valve-sticking, by supplying fresh oil from the suction port of an oil pump to flush a hydraulic circuit. CONSTITUTION:All component parts excepting an oil strainer and an oil pan are assembled. A fresh oil sucking-up pipe 8 is connected, at its one end, to the sucking-up port 53 of an oil pump in the thus obtained assembly 10, and is disposed, at its the other e...

PURPOSE:To obtain the titled device for converting a closed-end bladder into an open-end bladder by hole-forming machining, by a method wherein a bladder is rotated by supporting it, a part to be machined of the bladder is pushed out to a cutting position, and the part is cut. CONSTITUTION:The closed-end bladder 5 is rotated by supporting it by a bladder-supporting device 2, and the part 50b to be...

PURPOSE:To enhance current collecting efficiency to increase active mass utilization and decrease voltage drop by winding continuously formed electrode plates having a plurality of lugs in an elliptical shape having parallel parts and round parts and by welding lugs of same polarity located in corresponding positions to form a plate group. CONSTITUTION:Grids continuously manufactured by an expandi...

PURPOSE:To prevent noise occurrence by disengaging either one of clutch rings even in the idle running of a no-spin differential gear. CONSTITUTION:A pair of right and left front axles 20, 20 are rotatably inserted into a front axle case 21 and have respectively the inner ends spline fitted in differential hubs 22, 22. When a clutch (not shown) is disengaged, a no-spin differential gear can idle. ...

PURPOSE:To prevent noise occurrence by disengaging either one of clutch rings when a no-spin differential gear makes turning movement in idling. CONSTITUTION:A transmission shaft 47 is connected through a clutch (not shown) to an engine, and a brake device 50 is provided in a rotary portion of a power transmission path between said clutch and a center cam assembly 31 of a no-spin differential gear...

2076041 9112072 PCTABS00006 Disclosed are processes and apparatus for separating a desired solute (A), such as an optically active isomer, from a complex mixture (A, X, Y) using carrier (C) facilitated transport in an immobilized liquid membrane (50) or carrier (C) facilitated solvent extraction. The carrier (C) is a binding protein selected and/or engineered to immunochemically reversibly bind to...

The method is applied in electrical engineering and it reduces the time for production, as well as improves the parameters of the accumulator. The method consists in filling the accumulator with electrolyte, vacuumization, charging and discharging. Upon charging, the accumulator is vacuumed to a pressure of 0.5 to 20 kPa with a period of impact in vacuum of between 2 to 15 min.

An intrusion alarm system with an automatic exit control and a misset indicator which informs that someone has trespassed by opening a door during the resident's absence. This system comprises a sequential circuit which is enabled by mode selection by the resident at his/her going out and which stores the door's opening and closing signal produced as an output signal of a door open/closed detectio...

PURPOSE:To efficiently take out brightness from a fluorescent layer from a light emitting face by making a constitution wherein voltage is applied to a laminated structure comprising a fluorescent body or the fluorescent layer and a dielectric layer. CONSTITUTION:A transparent electrode 2 is formed on a glass substrate 1, a first dielectric layer (a)4a and a first dielectric layer (b)4b are formed...

PURPOSE:To obtain a moisture proof structure for permitting moisture-proofing by baking and solidifying an application type inorganic material with a moisture absorbing material blended in a recess of a glass cap opposite to a thin film EL device. CONSTITUTION:A thin film EL device A exhibiting EL emission is protected against moisture by using a glass cap 7 whose cross section is an approximate r...