PURPOSE:To provide high power performance and engine braking performance by prohibiting the control of an engine to run at a speed lower than idling speed and the control a starting clutch to release while a shift lever is shifted to a lower speed side than a regular shift position. CONSTITUTION:The control means 10 of an engine automatically starting and stopping device 8, while satisfying a spec...

PURPOSE:To provide a traveling working car, a chemical spraying car for agriculture, in particular, which interlocks a pedal mechanism and manual mechanism for controlling the engine speed of and has a transmission with high speed/low speed switching mechanism. CONSTITUTION:In a traveling working car which is capable of controlling the opening degree of a throttle of the engine 2 of the traveling ...

PURPOSE:To improve fuel consumption by cutting fuel as long as possible to a extent of not causing abnormality in engine operation. CONSTITUTION:This is a fuel supply controlling device in which an automatic transmission 1, carrying out speed change based on a plurality of parameters including a parameter corresponding to car speed, is connected to an engine 2 and which cuts the fuel supply to the...

PURPOSE:To improve the durability of a relay switch while reducing the heat load of valves by stopping brake fluid pressure generating operation when the brake fluid pressure of both of right and left wheels is lowered to the lowest set value and delaying brake fluid pressure generating operation stopping when the coefficient of the friction between the road face and wheels is small. CONSTITUTION:...

PURPOSE:To prevent the aggravation in the drive wheel slipping caused by the overlapping of an increase in engine driving force and a decrease in braking force by limiting the increase in engine driving force during the reduction of brake fluid pressure. CONSTITUTION:The traction control device 50 of a vehicle has an engine traction control means for controlling the driving force of an engine 5 an...

PURPOSE:To perform traveling at a stable and constant speed within a shorter time by quickly and properly reducing speed at the time of braking of a vehicle. CONSTITUTION:A brake device control unit 8 has a priority information map in which the priority is determined according to the strength of the braking force of auxiliary braking devices 3, 4 and 9 in each speed area to give the highest priori...

PURPOSE:To prevent further temperature rising by lowering the braking force of a retarder brake when the temperature of the retarder brake and prevent the aggravation of the feeling of a driver while restraining the sudden change in the braking force of the whole of a vehicle. CONSTITUTION:In an auxiliary braking force controlling device wherein when the temperature of a retarder brake 3, which is...

PURPOSE:To downsize a packing machine and support products having various sizes and shapes by means of a single packing machine by eliminating a process for folding a film into halves and directly placing a wide film roll on a cylindrically opening apparatus. CONSTITUTION:A wide film F drawn from a roll is guided along an inverse guide member 2, a half width of the film F is folded by 360 deg. alo...

PURPOSE: To precisely prepare a yarn end without damaging the same, by arranging a cutter in the vicinity of the opening of a preparing nozzle, and providing an additional yarn loop forming unit to a yarn end preparation device. CONSTITUTION: A diagonally winding bobbin winder incorporates a splicing device 8 between a yarn tension device and a yarn monitor device, and a swivel nozzle 16 having a ...

PURPOSE:To provide an acceleration slip control device which is constituted to rapidly relax control of suppression of drive torque when a vehicle is neither started nor accelerated even through control of suppression of drive torque. CONSTITUTION:When an accelerator pedal is pedaled and a car body speed VSO is below a set value V2 at S301 and 302, provided a value, being higher, of accumulation v...

PURPOSE:To prevent the generation of a shock during engagement of the clutch of a hydraulic automatic transmission during the starting of an automatic stop starting type engine. CONSTITUTION:Even when an engine is stopped through automatic stop processing at a cross and the feed of an oil pressure by an oil pump 51 is brought into a stop, the oil pressure of an AT hydraulic unit 53 is maintained b...

PURPOSE:To enhance the performance and durability of a differential by preventing pinion gears from collapsing, and reducing the localized abrasion of pinion-gear storage holes. CONSTITUTION:This differential includes a case 31, a first axial hole 43, a second axial hole 45, a first side gear 47, a second side gear 49, a first pinion gear 61, a second pinion gear 163, and storage holes 51, 53; the...

PURPOSE:To eliminate the need for a thrust washer so as to reduce the number of part items and the cost of a differential by designing the differential so that the engagement reaction force and the centrifugal force of pinion gears are sustained by a bearing portion formed in each side gear. CONSTITUTION:In a rear differential 7, right and left side gears 31, 33 are arranged in a case 21, are free...

PURPOSE:To provide a sufficient differential limiting force by means of a cam that utilizes the forces of gears constituting a differential mechanism. CONSTITUTION:This differential includes a differential case 21 driven by the driving force of an engine; helical pinion gears 47, 49 freely slidably and rotatably fitted inside storage holes 43, 45 provided in the differential case 21; wheel-side he...

PURPOSE:To provide a torque-sensitive preload type differential limiting function in order to enhance escaping performance when one wheel is slipping by providing friction plates in the inside portions of the differential case of a differential gear which are opposite to differential side gears, and providing differential springs for pressing the friction plates against the differential case. CONS...

The present invention relates to a container, system, and method for creating parenteral solutions at a site, remote from sterile environments. The system includes a flexible container that is empty except for a prepackaged amount of a solute that is housed in the interior of the container. The container includes at least one port and a sterilizing filter in communication with an interior of the p...

Methods of making sintered parts from a metal powder composition that contains an amide lubricant are provided. The composition comprises an iron-based powder and a lubricant that is the reaction product of a monocarboxylic acid, a dicarboxylic acid, and a diamine. The composition is compacted in a die, preferably at an elevated temperature of up to about 370 DEG C., at conventional compaction pr...

Monolayer and multilayer non-oriented polyester films comprising of at least one layer of an amorphous heat-sealing polyester wherein the heat-sealing polyester consisting essentially of terephthalic acid, ethylene glycol, and about 7-15 mol % cyclohexanedimethanol. The heat-sealing polyester has a heat of fusion greater than 0.5 cal/g and is sufficiently crystallizable to allow the drying of mixt...

There is now provided a polyol composition containing a polyol having polyester linkages, an aliphatic or cycloaliphatic C4-C7 hydrocarbon blowing agent, and a polyoxyalkylene polyether monool initiated with a C8-C24 fatty hydrocarbon having one alkylene oxide active hydrogen atom. We have found that the monool emulsifies the C4-C7 blowing agent in the compound having polyester linkages, to form a...

An electronic terminal of the type employing a card reading device mounted within the interior thereof accessible through an input port formed in a wall of the terminal. A shield formed of an elastomeric material is mounted adjacent the input port of the card reader to prevent the entrance of debris into the interior of the terminal. The shield provides at least two opposing movable overlapping fl...