PURPOSE:To provide a differential gear capable of making differential limiting force smaller at the backing time of a vehicle and at the engine brake using time than at the advance time of the vehicle. CONSTITUTION:A differential gear 7 has a differential case 21 rotatory-driven by the engine of a vehicle, pinion gears 53, 55 enclosed in storage holes 49, 51 provided at the differential case 21, a...

PURPOSE:To prevent an increase of the shaft length and the distance between shafts of a transaxle device by providing the second epicyclic gear type transmission device convertible between plural gear shift stages around the differential shaft of a differential device. CONSTITUTION:The torque from a main epicyclic gear type transmission device 5 is transmitted to a differential device 70 through a...

PURPOSE:To lessen the decreasing amount of electrolyte in battery jar formation by specifying the current density of charging current in the later stage of battery jar formation of a battery that is not yet charged, comprising plate that is not yet formed, stored in a cell provided with a specific rib. CONSTITUTION:At least two ribs 1 of 0.3mm in height are provided on both side surfaces that are ...

PURPOSE:To enhance the acceleration capability and the steering stability of a vehicle incorporating a output power control system and a differential limit torque control system, by increasing the differential limit torque control gain in a high lateral acceleration condition while increasing' the output control gain in a low lateral acceleration condition upon occurrence of a slip during accelera...

PURPOSE:To get a position-free battery by putting the liquid in an electrode plate in shorter condition than a proper amount, and charging sol solution, and shifting the sulfuric acid water in sol to a group of electrode plates, and putting the sol out of fluidity. CONSTITUTION:An excessive amount of dilute sulfuric acid electrolyte more than a proper amount is injected into a group of electrodes ...

PURPOSE:To prevent generation of seizure by providing a protective body for covering a shaft side spline part to protect an oil seal body from damage in attaching of an axle shaft, and making this protective body function as a bush after attaching of the axle shaft. CONSTITUTION:In a transmission, shaft side spline parts 82 (82-1, 82-2) of axle shafts 80 (80-1, 80-2) are spline-connected to gear s...

PURPOSE:To prevent the stick-out of a vehicle by adjusting the transmission speed in changing and controlling the transmission ratio of a continuously variable transmission to be small to suppress the rapid release of the inertia energy of the engine due to the delay in operating the booster when the boost pressure condition of the engine is over the prescribed value. CONSTITUTION:The line pressur...

PROBLEM TO BE SOLVED: To brake a drive shaft coupled with a second rotor by means of a motor comprising a first rotor coupled with the output shaft of a prime mover and a second rotor rotating relatively to the first rotor. SOLUTION: A power transmission 20 coupled with the crankshaft 56 of an engine 50 is provided with a clutch motor 30 and an assist motor 40 and controlled through a controller 8...

PROBLEM TO BE SOLVED: To simplify adjustments by normalizing various engine characteristic curves. SOLUTION: An engine torque command value for making actual vehicle speed coincide with the desired vehicle speed is computed and is converted to an engine torque command value per unit displacement using equivalent displacement set for each engine. From the nonlinear steady-state characteristic map o...

A medical dressing (10) comprising an embossed, thin polymeric film coated (11) on one side with a medical grade, pressure-sensitive adhesive (16). The embossed film (11) has a low coefficient of friction, preferably less than about 0.6, on the outer adhesive free surface which makes the film particularly resistant to unintentional removal by rubbing forces. The film is intended primarily for use ...

The improved rotary cutter performs cutting by making a knife edge portion of a rotating disc-shaped knife (2) bite into a surface of a sheet (1) being successively fed. On the underside of the traveling sheet (1), a brush (4) consisting of rod-shaped brush elements is fixed on a backing table (3) between point A and point B over the entire region in the lateral widthwise direction of the sheet (1...

PURPOSE:To serialize the various modes of orthogonal gear speed reducers with motors (including low backlash type ones) required by users with ease. CONSTITUTION:Component force in the axial direction of a motor shaft 103, which is caused by the meshing of a hypoid pinion 104 with a hypoid gear 105, is held only by the part of a bearing 113 at the gear box side out of paired bearings 113 and 122 s...

An interline transfer type area image sensor which operates in a non-interlaced mode and has an array of columns and rows of photoreceptors in which charge from each pixel is transferred into a stage of a vertical two-phase CCD shift register formed by adjacent electrodes of the CCD. Each electrode of a stage has a separate voltage clock. An ion implant barrier region is formed under an edge of ea...

PCT No. PCT/SE95/00874 Sec. 371 Date Jan. 21, 1997 Sec. 102(e) Date Jan. 21, 1997 PCT Filed Jul. 17, 1995 PCT Pub. No. WO96/02345 PCT Pub. Date Feb. 1, 1996The present invention concerns a method, according to which powder compositions of iron-based particles are admixed with a thermoplastic material and a lubricant. The obtained mixture is compacted at a temperature below the glass-transition tem...

PCT No. PCT/EP93/01957 Sec. 371 Date Jan. 27, 1995 Sec. 102(e) Date Jan. 27, 1995 PCT Filed Jul. 22, 1993 PCT Pub. No. WO94/03532 PCT Pub. Date Feb. 17, 1994The present invention relates to hard polyurethane foams. These foams are produced by the reaction of 1) polyisocyanates, with 2) compounds having molecular weights of from 92 to 10,000 and having at least two hydrogen atoms which are reactive...

PURPOSE:To obtain the title element which can provide a luminescence of a sufficient luminance at a low driving voltage and can retain the initial luminescent characteristics even after a long-term storage by adding a specified fluorescent color to an organic hole transport layer and an organic electron transport layer. CONSTITUTION:A 1,2,5-thiadiazolopyrene derivative of the formula (wherein R<1>...

The deck chair has a U-shaped back stand (12), bent at its upper ends to form armrests (13), and a U-shaped front stand (11) with slightly curved arms, which are joined to the back stand at their upper ends. A stabilizer (19) is a single thin shaped metal bar hinged to the chair back (15) and can be fixed to keep the back upright until the person is safely seated. The stabilizer can be released si...