PURPOSE:To reduce the turning radius of a vehicle to restrain rear wheels from projecting, by providing a mechanism for transmitting a predetermined difference in rotational speed to two shafts, and a means for coupling the transmission mechanism to the drive side when both right and left steered wheels are set at a maximum steering angle. CONSTITUTION:When a running vehicle is turned to, for exam...

PURPOSE:To prevent occurrence of shock upon speed shift, by determining a desired throttle valve opening degree for obtaining an engine output torque or rotational speed which is suitable for at least one of cycles of lowering the output, interrupting the transmission of power and performing the retransmission of power. CONSTITUTION:A control device 16 determines a desired throttle valve opening d...

PURPOSE:To perform a simple and reliable emergency stop, by 8 method where in, through control of a control switch along with control of a gear shifting lever to control gear shifting of 8 transmission, a main clutch located to the transmission is engaged and disengaged. CONSTITUTION:When a control switch 6 mounted to a gear shifting lever 3 in a neutral position is turned ON, through the action o...

PURPOSE:To ensure a sufficient amount of electricity in quick charge, and to retard gas evolution during charge to increase charge efficiency by using a positive plate prepared by filling an active material in a current collector coated with a hydroxide, and by using a negative plate inside which lead sulfate exists. CONSTITUTION:By filling an active material in a current collector of a positive p...

PURPOSE:To improve the high ratio discharge characteristic and restrict an exhaust of the positive electrode active material to prolong a lifetime by interposing the gelled electrolyte support between the active material and the inner surface of a clad tube. CONSTITUTION:The gelled electrolyte support 104 is interposed between the inner surface of a clad tube 101 of a clad type positive electrode ...

PURPOSE:To improve health of a man and durability of a housing, by a method wherein an earth floor heater is mounted to a housing, a heat exchanger to exchange heat between internal and external air is disposed in an attic space, and an irradiating mechanism to introduce solar light and heat to a room is provided. CONSTITUTION:An air cycle passage 22 is formed by an attic space 12, a vent passage ...

PURPOSE:To make feeling of speed change in kick down good, together with getting sufficient driving force in full open starting by providing a gear ratio detecting means, an engine load detecting means, a judging means and a speed change pattern changeover means. CONSTITUTION:When throttle opening is judged by a means C to be fully open, whether the vehicle is in full open state or in kick down ac...

PURPOSE:To correct the fluctuation of the widthwise force of a tire in a condition that the tire is attached, by a method wherein the (-) position of the rigidity of X-axis in the shoulder of the tire is worked by buffing in accordance with the fluctuation of rigidity, which is generated from the shoulder of the tire. CONSTITUTION:A drum 2 is pushed against a rotating tire W to detect the rigidity...

PURPOSE:To aim at enhancing the bending rigidity by accommodating a secondary intermediate shaft and a part of a gear train on an output shaft in an auxiliary mission casing, and by accommodating the remainder and a counter gear train in a main mission casing coupled to the front section casing. CONSTITUTION:Power for driving a differential gear unit arranged at the substantial center of a vehicle...

A GaAs semiconductor device comprises a Si substrate (1), an intermediate layer (3, 4) formed on the substrate and a GaAs layer (2) grown on the intermediate layer. The intermedite layer includes constituent GaP/GaAsP and GaAsP/GaAs superlattice layers and additionally AlP and AlGaP thin films.

PURPOSE:To prevent the quick advance immediately after the start of an engine by detecting the operation of a brake pedal and allowing the start of the engine only when it is detected. CONSTITUTION:The starting system of an engine is constituted of an ignition switch 1 and a starter motor 2 operated when the ignition switch 1 is turned on. A detecting means 3 detecting the operation of a brake ped...

In a transmission case section for an automatic transaxle case, a center axis of a governor receiving portion is arranged between a center axis of a main power train and a center axis of a reduction gear when viewed in plane perpendicular to the center axis of the main power train and the center axis of the final drive gear. A nearly right-angled triangular reinforcement is formed in a corner betw...

PURPOSE:To obtain both the prevention of consumption in current, pumping loss, and noise and the improvement in responsiveness in the generation of a transmitting torque by limiting the generating timing of clutch engaging force while preventing controlling hunting. CONSTITUTION:A friction clutch element (e) for generating a transmitting torque which is variable in accordance with an engaging forc...

A method and apparatus of making coiled plate, sheet in coiled form or discrete plate. The apparatus is an intermediate thickness slab caster and inline hot strip and plate line. The apparatus includes a continuous strip caster forming a strand of between about 3.5 and 5.5 inches thick; a shear for cutting the strand into a slab of desired length; a slab table including a slab takeoff operable tra...

PURPOSE:To improve the running stability by controlling a rotation suppressing device to make the slip rate of the higher driving force generating side wheel slower than that of the lower driving force generating side wheel, on condition that the lateral force is more important in the running condition. CONSTITUTION:A driving force detecting device (c) is furnished to detect which side is the high...

PURPOSE:To obtain a compact and reliable engine torque detecting method by regarding an addition value of a product value obtained by multiplying a change rate of an engine speed by a designated value and a detected transmission torque of a driving force transmission as an engine torque detection value. CONSTITUTION:A transmission control unit TCU 16 computes and stores an engine speed and its cha...

PURPOSE:To reduce the loss of a light transmission by machining the inclined face of the backmost part of a groove in a vertical face by a high energy beam after forming the groove by a pyramid tool made of a sintered hard alloy in the case of forming the groove for an optical fiber connection on an optical integrated circuit board by a brittle member to make the combination with an optical fiber ...

PURPOSE:To improve a response of a slip control while a brake control and a throttle control are prevented from interfering each other by controlling the controlling amount of a throttle valve to correct toward throttle shutting corresponding to the controlling power of a braking apparatus by a brake control. CONSTITUTION:The title apparatus has an acceleration slip detecting means M2 to detect an...

PURPOSE:To improve controllability by judging a skid state in a vehicle from each sensor output of lateral acceleration, steering angle and car speed, and when it comes off the setting range, judging it to be a turning limit and controlling a clutch. CONSTITUTION:A controller 44 controls a torque distribution via front and rear clutches 10, 18 on the basis of each rotational frequency of front whe...