PURPOSE:To reduce the backlash between a pinion gear and both side gears to eliminate noise and as well to restrain the number of component parts from increasing, by disposing a resilient member between a differential gear casing and one of side gears. CONSTITUTION:A hollow shaft 1 as an input shaft is associatingly coupled with a drive shaft 3 by means of a speed change unit 5. A pinion gear 11 i...

PURPOSE:To run a vehicle at an optimum fuel consumption by driving selectively either an engine or electric motors, or both of them, according to the running condition of the vehicle. CONSTITUTION:An engine 10 to drive either the front wheels 2 or the rear wheels 3, electric motors 30 to drive either the rear wheels or the front wheels other than those driven by the engine 10, and an automatic tra...

PURPOSE:To eliminate the need for the artificial operation of a diff-lock device and to cancel trouble with the operation by performing no actuation of the diff-lock device when a right or a left braking device is braking its wheel. CONSTITUTION:There are provided a diff-lock device 14-equipped differential gear 8 for distributing the revolution of an engine to left and right wheels 5, 5 for trans...

PURPOSE:To prevent data from being erroneously read out as the time of data interference with no hardware constitution complicated and also with no capacity of a RAM made small in a processing unit which transmits data between a plural number of control units and the RAM. CONSTITUTION:Under a certain control period when data written in a dual port RAM by a CPU is interfered with data read out of t...

PURPOSE:To perform slip control excellently by optimizing control gains for setting the controlled variable for slip control in response to control condition. CONSTITUTION:Torque to be imparted to each front driving wheel is controlled so that the actual slip value of each front driving wheel 1FR and 1FL coincides with the specified target value of an engine or the target value of braking control....

PURPOSE:To perform slip control more excellently by optimizing control gains for setting the controlled gain of slip control in response to the running condition of a vehicle. CONSTITUTION:Torque to be imparted to each driving wheel is controlled so that the actual slip value of each front driving wheel 1FR and 1FL coincides with a target value for an engine or the target value of brake control. I...

PURPOSE:To make switch-over between forward speed and reverse one with excellent feeling by performing booster control in such a way that hydraulic oil to be supplied to oil passages is gradually increased in pressure while being interlocked with the operating speed of a shuttle gear shifting lever, and thereby constituting a hydraulic clutch to be slowly engaged therewith. CONSTITUTION:When a shu...

PURPOSE:To make the movement of a lock device constant even if there exists dispersion in the range of the movement of the pedal operation by providing a moving member which enables a lock lever to be released from the specified range of the positioning plate of a position pin as a foot brake pedal is depressed. CONSTITUTION:The moving member 15 of a lock device 11 is arranged close to one end sec...

PURPOSE:To perform slip control more effectively by optimizing a control setting value for slip control. CONSTITUTION:Given torque to driving wheels is controlled so that the actual slip value of front wheels 1FL and 1FR as driving wheels can be a given engine target value STE or a brake control target value STB. A control setting value for slip control, e.g. target values STE or STB, a control st...

PURPOSE:To smoothly convey a tube yarn, in the case of a tube yarn supply system for an automatic winder. CONSTITUTION:A bobbin return path 6 from an automatic winder is branched into a residual yarn-provided bobbin conveying path 11 and an empty bobbin conveying path 10 and also thereafter each conveying path is joined and connected to the empty bobbin conveying path 10 to provide a bobbin stripp...

PURPOSE:To obtain a hydrogen producing device of high efficiency and low cost type using solar energy. CONSTITUTION:This device consists of a metal sodium heater 6 using solar energy, alkali metal thermoelectric converter 4 connected to the heater 6 and equipped with a cooling jacket 34 in the lower temp. side, steam heater 5 using solar energy, electrolytic cell 1 having a solid oxide electrolyte...

PURPOSE:To obtain calorific power maximum for each wind speed, reduce starting wind velocity and improve wind power thermal transducing efficiency by always applying the optimum revolution load at the wind speed. CONSTITUTION:A windmill 21 and the rotary body 57 of a heating device 33 are connected, and the heating device 33 and a thermal accumulator 37 are connected so that a liquid thermal mediu...

PURPOSE:To absorb or radiate heat by using a radiation beam by providing a heat absorbing radiation beam-transmission unit for transmitting only a radiation beam having a wavelength less than a special value, and a heat radiation beam transmission unit for transmitting only a radiation beam having a wavelength more than a special value, and switching them to absorb and radiate the heat. CONSTITUTI...

PURPOSE:To enable high speed operation by aligning a separator supplied to a first adsorption roller and a plate supplied from a conveyance unit to almost the same location in the position corresponding to the separator folding section and the front end of the plate and inserting them by a first and second adsorption rollers. CONSTITUTION:A separator (a) is sent to the lower part of a first adsorp...

PURPOSE:To enable a plate group to be effectively formed, by synchronizing the vertical movement of a lift base with the horizontal movement of the claw parts of a supporting part from the side board of a guide frame, and heaping the plates in sequence on the claw parts from upward to downward. CONSTITUTION:At the time when conveyance by means of a conveyor 1 is stopped by the rear board 7a of a g...

PURPOSE:To enable correct centering to be carried out without damaging a plate, by constituting a position-correcting structure with a pair of eccentric rolls and a position-correcting belt which is streched between said rolls and moves toward the direction and at the velocity respectively identical to those of a conveyor belt. CONSTITUTION:With regard to two pairs of respective two rolls 5a, 5b a...

PURPOSE:To soften the variation of the clutch pressure on stepping-in a pedal by varying the output pressure of an inching valve according to the displacement of the valve, even if the output pressure supplied from a pressure adjusting valve is low, by means of a inching control apparatus for the transmission gear of an industrial car. CONSTITUTION:The upper-half figure of an inching valve 20 show...

PURPOSE:To smooth start and acceleration by providing a damper where resistance will function only in the direction for coupling a clutch thereby loosening clutch. CONSTITUTION:Upon turning of lever 3 to position 3A, a clutch arm 6 and clutch lever 9 will rotate to roll a release lever 13 around a shaft 131 through a spring 10 and cable 11 thus to disconnect a clutch 12. Here a damper arm 14 is tu...

PURPOSE:To aim at improving safety by outputting a mechanical brake signal to a mechanical brake from a mechanical brake signal generating means when the voltage signal applied to an electric servo device from a speed setting lever corresponds to the speed O. CONSTITUTION:In a control circuit 20, when a speed signal (a voltage signal) generated corresponding to the position of a speed setting leve...

PURPOSE:To change over brake control quickly by sensing if there is hose drawout from detection signal about the load on a roller of a hose drawout part and the received wave from a portable transmitter, and by controlling brake to a hose reel on the basis of input of that member which is switched earlier. CONSTITUTION:It is sensed whether a sprinkling hose 14 is drawn out of a hose reel 44, from ...