PURPOSE:To easily fix a rotor by pressing a pressing part without tightening and also to cause an operator to easily make a judgement on the fixed sate of the rotor. CONSTITUTION:A rotor body 34, a rotor 33, a rotor supporting part 2, a hole 5 whose inner diameter is made large, a cylindrical fixed part 6, a backup pin 7, a pressing part 6 and a receiver 9 constitute the method. When the rotor bod...

PURPOSE:To provide a working device capable of preparing a long-sized sheet and being driver for a long time, by a method wherein a protective sheet on a mounting rest is stretched between a supply reel and receiving reel, and renewed continuously in accordance with application limit. CONSTITUTION:A film 22 put on a protective sheet 5 stretched over a mounting rest 2 is pressed, cut off into a spe...

PURPOSE:To heighten the traveling stability of a vehicle by controlling differential limiting torque so that the vehicle obtains a desired yaw rate, using an active control type differential limiting device. CONSTITUTION:A vehicle provided with an active control type differential limiting device (a) is provided with a means (b) for detecting the vehicle speed, a means (c) for detecting the steerin...

PURPOSE:To contrive the stable acceleration of a vehicle on a split mu road or the like by controlling differential limiting torque so that the slip factor of one wheel is kept in a specified range, using an active control type differential limiting device. CONSTITUTION:A vehicle provided with an active control type differential limiting device (a) is provided with a means (b) for detecting the ve...

PURPOSE:To slight an automatic transmission to a low speed side at the time of turning travel and secure an engine brake at the time of turning travel and after that, enhance the performance of acceleration and further prevent an abrupt change of torque even at the time of this speed change. CONSTITUTION:When a controller 3 judges turning travel from a yaw rate PHI, a controller 8 commands the cha...

PURPOSE:To reduce a speed change shock at the time of down-shift speed change by correcting the starting rotation ratio of engine output changing control according to the actual torque converted characteristic. CONSTITUTION:An engine controller 12 is provided for the engine output changing control of an engine 1. The engine controller 12 receives a throttle opening (TH), the number of revolution (...

PURPOSE:To improve slip ceasing efficiency by providing a shift up instruction means to output an instruction to shift up an automatic transmission to an automatic transmission control device only in the case of a low friction load surface, at the starting of a traction control by receiving the output of a road surface friction detecting means. CONSTITUTION:An object slip amount of driving wheels ...

PURPOSE:To make the speed change operation in a vehicle easy, to prevent the transmission of the motive power impulsively from either one side to the other side of the engine side and the wheel side, and furthermore, to simply the structure of the speed change gear and to make the assembly work easier. CONSTITUTION:A speed change operating mechanism 29 to operate a speed change gear 12 is provided...

PURPOSE:To improve the braking feeling and to reduce the braking distance by providing a shift converting means to up-shift correct an automatic transmission when a cylinder for braking is pressure reduction controlled by an antiskid control means, and to down-shift correct the automatic transmission when the cylinder for braking is pressure increase controlled. CONSTITUTION:A specific value of ex...

PURPOSE:To ensure control reliability and provide cost reduction with a simplified control system by carrying out mutual communication for control between the control part of a slip controller and the control part of an air bag device. CONSTITUTION:In a vehicle which is provided with a slip controller (ABS) and an air bag device, an ABS control part 43 and an air bag control part 55 are controlled...

PURPOSE:To maintain responsiveness to suppress a shift up slip while suppressing the heat load of valves. CONSTITUTION:In a traction control device for vehicle in which an engine traction control and a brake traction control can be performed, a rear wheel ABS hydraulic system 30, a front wheel ABS hydraulic system 50, and a rear wheel TCS hydraulic system 70 are provided in a braking system 20 and...

PURPOSE:To prevent dust and dirt accompanying with a movement of a hard disk case in a clean packaging bag from generating by a method wherein the inside of the clean packaging bag is vaccumized to deaerate, and the hard disk case in which a hard disk is contained is tightly joined to the internal surface of the clean packaging bag. CONSTITUTION:A hard disk package 1 is constituted in such a manne...

PURPOSE:To prevent flashes from falling when upper and lower halves are joined by welding to make a nylon-made reserving tank. CONSTITUTION:A flash-holding chamber including and holding a flash produced by thermowelding on the peripheral edge of a welding surface Y of welding parts 40, 50 is formed on the inner periphery of the welding parts 40, 50 respectively provided on an upper tank and a lowe...

PURPOSE:To provide flexibility at execution timing by comprising a permanent power generating plant, a temporary air compressing plant, a temporary piping provided with a foreign matter recovery device for recovering a foreign matter from a steam turbine inlet valve upstream side to a condenser, and a permanent piping in the power generating plant in a blowing out facility in a combined cycle elec...

PURPOSE:To feed exhaust gas from a boiler to a high pressure stack gas cooler and a low pressure stack gas cooler for heating feed water in a steam turbine system and to control exhaust gas quantity to the high pressure stack gas cooler so as to reduce stored heat in the high pressure stack gas cooler in the case of a partial load by additionally arranging a gas turbine plant in a steam power plan...

PURPOSE:To accomplish proper load distribution between a gas turbine and a steam turbine so as to stabilize a frequency by providing a means deciding a proper load distribution value between the gas turbine and the steam turbine on the basis of a gross generation output signal and a means deciding a main steam control valve travel setting value and a gas turbine speed control governor setting valu...

A method for determining the direction of a borehole during drilling comprises determination of inclination angle theta and highside angle phi from gravity acceleration ( &upbar& g) measurements and determination of azimuth angle psi from magnetic field ( &upbar& B) measurements along with the calculated inclination angle theta and highside angle phi , the determinations being carried out...

Apparatus for determining the position of a mobile vehicle relative to a fixed location marker device (10,20) which comprises a coil (22) energized to emit a magnetic field composed of lines of magnetic flux extending radially and arcuately from the ends of the coil's longitudinal axis (12). A sensor unit mounted on the mobile vehicle comprises four identical sensing coils (A,B,C,D,) each responsi...

A process for molding a semi-rigid integral skin foam which comprising an integral skin having a low degree of foaming and a core having a high degree of foaming. The process includes evacuating a mold cavity to a pressure of from above 50 to 700 Torr; injecting, into the evacuated mold cavity, a polyurethane material which contains a polyol component and an isocyanate component with air bubbles i...

The invention is a rigid polyurethane foam to which a base stock lubricating oil made of at least 55 weight percent paraffinic carbons and less than 10 weight percent aromatic carbons has been added as a hydrophobic agent protecting the polyurethane foam from reacting with environmental moisture. The foam is useful for deposit in railroad spike holes or any structural member having a cavity and wh...