PURPOSE:To realize bead setting with high accuracy without any offset of a bead relative to a main drum, by intermediately providing a forced reciprocation mechanism for shifting between a condition where a front end face of a bead-retaining ring is on the forward side of a front edge of a bead-receiving ring and a condition where the front end face is on the rear side of the front edge. CONSTITUT...

PURPOSE:To enable a bead to be retained properly and prevent a tire component from becoming off-centered, by composing a bead-retaining ring of a plurality of segments disposed along the circumferential direction so as to be minutely movable in radial directions, and connecting a reciprocating mechanism to each of the segments. CONSTITUTION:A pair of bead-retaining parts 99 and 100 disposed on opp...

PURPOSE:To improve a coefficient of use of a positive electrode active material and improve energy density by using an electrode board with metallic tin or a tin compound added between positive electrode active materials. CONSTITUTION:When metallic tin or a tin compound is added between positive electrode active materials, this is oxidized during formation or charging, so that tin oxide which is h...

PURPOSE:To increase a reaction area of an electrode board, improve a coefficient of use of an active material and improve energy density by using an electrode board with a cesium compound added between positive electrode active materials. CONSTITUTION:By adding a cesium compound between positive electrode active materials, active material particles can be fine to have a surface area increased. Thu...

PURPOSE:To increase a reaction area of an electrode board, improve a coefficient of use of an active material and improve energy density by using an electrode board with a compound of alkaline earth metal added between positive electrode active materials. CONSTITUTION:By adding a compound of alkaline earth metal between positive electrode active materials, active material particles can be fine to ...

PURPOSE:To prevent the furtherance of the aggravation of a steering characteristic and the furtherance of the loss of drive force even if drive force distribution changes, by conducting correction control so that the more there may be an inner wheel racing amount or an inner wheel racing equivalent amount, the less or unincreasingly there may be a wheel load move ment amount on a wheel load distri...

PURPOSE:To make a car body gravity center nearer to a position at the front and at the same time narrow a space between a transmission and an engine and realize the shortening of the car body, by providing a comparatively heavy rear differential gear at the forward position of the transmission which is in the front position of the car body. CONSTITUTION:A motive power travel car body 2 is equipped...

PURPOSE:To make mounting rigidity small at the time of a winding up amount being limited, by combining a divided final decelerator side propeller shaft with a final decelerator so as not to be bent, and also providing a mechanism which supports partially the weight of the final decelerator, at the final decelerator side propeller shaft. CONSTITUTION:The 1st propeller shaft 4 which is connected to ...

PURPOSE:To restrain a drive wheel slip without causing an engine stalling at the time of an engine cooling state, in a case in which the drive wheel slip is restrained by the lowering of an engine output, by conducting a shift up control instead of an engine output lowering control at the time of an engine cooling. CONSTITUTION:A vehicle drive wheel slip is detected by means of a means (a), and al...

PURPOSE:To adjust the voltage and conduct the other necessary actions in an early stage by providing a control unit adapted to generate a designated signal when the rise speed of electric input in an electromagnetic coil is out of a designated range. CONSTITUTION:In a control unit 115, coil resistance is calculated from signals of coil voltage and coil current input from a voltage sensor 121 and a...

PURPOSE:To efficiently adjust meshing by supporting a transmission case on the case of an actuator through a bearing and screwingly supporting the actuator case on a carrier case. CONSTITUTION:When actuator cases 17 and 19 are turned rightward or leftward around the axis centers of the output shafts 7 and 9, the cases 17 and 19 shift so as to approach or separate from a driving pinion gear 47, for...

PURPOSE:To suppress the driving wheel slip in good order by reduction- controlling the torque increasing action caused by a torque converter according to the degree of the generation of the driving wheel slip. CONSTITUTION:In traveling, the driving wheel slip of a vehicle is detected by a driving wheel slip detecting means (b), and a target speed ratio determining means (c) determines the target s...

PURPOSE:To increase an amount of collecting heat and increase an efficiency of system by a method wherein a heat pump system and a complex system of a solar cell of solar heat power generating system and a fin-type heat collector are integrally formed and an operation can be carried out while a temperature of working fluid in the heat collector is lower than a surrounding air temperature. CONSTITU...

A rotary shredding apparatus having in combination counterrotating cutter supporting shafts operated by a reversible fluid pressure driven motor, and a fluid flow circuit connected to the reversible motor and including a pump supplied source of fluid at a predetermined nominal operating flow rate, a fluid pressure responsive relief valve operative for fluid flow exceeding said predetermined nomina...

PURPOSE:To prevent any deterioration of a lead storage battery which might be caused by defective contact between a plate and electrolyte when the battery is left after overdischarge by placing, either on the surface of a plate or in the interface between the plate and a separator, a compound the liquid-holding ability of which changes as pH changes, especially one having a higher liquid- holding ...

A method for the splicing of two twisted staple yarns includes the steps of untwisting portions of each yarn, drafting these portions to form beards and retwisting the beards to form the splice. In one aspect of the invention, the untwisting is effected by rolling the yarns between two surfaces at nip point to rotate the yarns. In a second aspect, each yarn is gripped between nips at two locations...

The transmission device comprises first (I) and second (II) groups of input and output gears arranged on either side of a set of input (22, 28, 34, 46, 56,40) and output (24, 32, 36, 48, 54, 42) gears which produce a given speed ratio. The presence of first and second clutches (18, 20) enables both sequential as well as non-sequential gear shifting between the groups of gears and/or the gear locat...

PURPOSE:To enable the diameter of a governor drive gear secured to the carrier of a planetary gear assembly to be made small, by disposing the governor drive gear between the outer peripheral wall of a cylindrical part and the inner peripheral wall of a transmission casing. CONSTITUTION:A planetary gear assembly 3 in a second planetary gear transmission mechanism 500 comprises a carrier 32 secured...

PURPOSE:To prevent the engine stall by varying the fuel cut restoration revolution speed for suspending the fuel cut to a high value, on the shift change form N range to D range in racing state. CONSTITUTION:A fuel cut-off control means F is installed which outputs a fuel cut-off signal into a fuel feeding means E when the engine revolution speed detected by a revolution speed detecting means A is...

PURPOSE:To operate the reengagement of an on/off clutch in a low speed condition and improve safety by bringing a stepless transmission under a disconnected condition of said on/off clutch, to a low speed condition corresponding to the position of a speed change lever in preference to the set value of deceleration. CONSTITUTION:When a clutch 14 is disconnected while traveling, a signal from a dete...