PURPOSE:To suppress the useless time to the min. by detecting the transmission load by utilizing the electrical control characteristic of an electromagnetic proportional reducing valve with which the pressure increasing characteristic to a hydraulic clutch can be arbitrarily varied and varying the initial-pressure increasing speed on the basis of the result of the detection. CONSTITUTION:An electr...

PURPOSE:To improve the safety of a vehicle as well as the fuel consumption by a method wherein the speed changing ratio and the slottle opening are controlled according to signals from an acceleration pedal sensor and a vehicle speed sensor. CONSTITUTION:An output from the acceleration pedal sensor 10 is inputted to a driving power pattern determinating instrument 14, and an output from the vehicl...

PURPOSE:To prevent engine stop by setting the aimed revolution speed to the value higher than the fuel-cut revolution speed when a throttle-valve opening- degree is at an idle opening-degree and a car-speed is a prescribed value or more, in a car which is equipped with a continuously variable transmission and performs fuel cut in deceleration. CONSTITUTION:The controller of a continuously variable...

PURPOSE:To lessen the diameter of the screw gear part of side gear while its spline part is secured with a sufficient diameter, by separating the screw gear part of at least one of the side gears of a differential device for car from the spline part in the axial direction. CONSTITUTION:At least on one of the side gears 40, 50, the screw gear parts 42a, 52a are separated from spline parts 41a, 51a ...

PURPOSE:To relieve shock by increasing the engagement force of a lockup mechanism when deceleration is sensed, and by restricting this engagement force during decelerative operation when an auto-transmission makes mesh shift. CONSTITUTION:The auto-transmission 10 of an engine 1 is composed of a torque converter 11 and a transmitting mechanism 12, and is equipped with a lockup mechanism 13, an oil-...

A liquid absorbing pad, in particular for use in hygiene articles and sanitary products, such as diapers, bed pads, sanitary napkins, pads for incontinence, panty shields, nursing pads or the like, is produced in a dry and direct process on the basis of wet-strength and/or coated paper waste, especially originating from the production of food packages, milk carton packages, deep-freeze packages, d...

A yarn stripper device for stripping unused yarn from a yarn carrier 11 comprises a yarn carrier receiving station 10, a magazine for holding a stack of yarn carriers 11 and for discharging the carriers one by one to the receiving station, a pusher device 13 linearly reciprocatable through the receiving station 10, a first set of jaws 14 arranged to engage around each yarn carrier 11 as the latter...

A bobbin magazine for mounting on an end plate of a traveling service tender comprises a band movable on an endless path, compartments on the band to receive sticks of telescoped bobbins and a transfer device to transfer sticks from the magazine to the tender. The magazine can be hinged to the tender so that the magazine can be swung out to expose the end plate.

PURPOSE:To eliminate the need for using a polarized beam splitter or the like and to obtain an extremely compact and inexpensive Faraday rotator by integral ly forming a diffraction grating at least on one end face of the Faraday rotator. CONSTITUTION:The Faraday rotor 1 integrated with the polarizer forms the diffraction grating 3 integrally with one end face of the Faraday rotor 2. When the diff...

PURPOSE:To prevent the disconnection in an injection port by a sealing part and to obtain the liquid crystal display device of a high display grade by providing the liquid crystal injection port on the side of the signal input terminal part of a transparent substrate which is not formed with color filter layers. CONSTITUTION:The color filters 7 of three colors; red, blue and green are formed on th...

PURPOSE:To seal a hermetic case for moistureproofing so as to prevent aging deterioration of an electroluminescent element by surrounding a group of layers of organic compounds, etc., and disposing the group of layers of organic compounds inside the hermetic case, and retaining diphosphate pentoxides in a retaining container disposed separate from the group of layers of organic compounds inside th...

PURPOSE:To prevent penetration of water and also prevent deformation of an electroluminescent panel by sandwiching the electroluminescent panel between moistureproof films from both sides of the panel, and joining to each of the moistureproof films an auxiliary panel of the same outer shape as the electroluminescent panel, and heating and pressing the moistureproof films from both sides. CONSTITUT...

PURPOSE:To prevent a light-emitting film, a second insulating film and a second electrode from being peeled from one another by using as a developer, a washing liquid for the developer and a washing liquid for an etchant an organic solvent which does not substantially contain water. CONSTITUTION:A resist 7 exposed is developed by an organic developer and the developer is washed and removed by an o...

The utility model provides chair feet with fixed caster which can cause a chair to realize rolling friction with the ground. The utility model has the advantages of simple structure, low cost and long service life. Users can conveniently move a chair backwards and forwards. The utility model can be formed by increasing a caster holder, a caster, a shaft and a pad on the lower part of chair feet ma...

A positive drive is disclosed of the type including an input (11, 13, 21) and a pair of outputs (27, 29) in which torque is transmitted from the input to the outputs by means of a pair of drive coupling members (23 and 25) and clutch assemblies (35 and 37). In order to frictionally dampen any undesirable oscillations of the input relative to the outputs, each of the clutch assemblies includes inac...

PURPOSE:To prepare the title powder improved in powder flow without using any organic liquid by agitating and disintegrating a polytetrafluoroethylene powder at a specified temperature in an organic liquid-free aqueous medium. CONSTITUTION:A polytetrafluoroethylene powder of a particle diameter of 600mum or below is agitated and disintegrated at 60-100 deg.C on an apparatus provided with an agitat...

PURPOSE:To prepare the title powder improved in apparent density, denseness and electrical properties without using any organic liquid by agitating and disintegrating a polytetrafluoroethylene powder at a specified temperature in an organic liquid-free aqueous medium. CONSTITUTION:A polytetrafluoroethylene powder of a mean particle diameter of 100mum or below, desirably 50mum or below, is disperse...

PURPOSE:To manufacture a superconductive wire having reliability and long- term stability by shaping an oxide superconductive material in the form of a tape. CONSTITUTION:A sintered oxide superconductive material of composition represented by a formula of A-B-Cu-O is pulverized to be subsequently filled into a silver pipe, and the resultant pipe is drawn in a wire and formed in the shape of a tape...

PURPOSE:To obtain a superconductive wire having an excellent superconductive characteristic by mixing various kinds of powder consisting of materials forming oxide superconductive materials at a prescribed ratio, spinning this mixture to form precursor fibers and impregnating the fibers with a reinforcing matter. CONSTITUTION:First, powder of an organic metal compound and oxide superconductive mat...

A unit for drum brakes comprises a fixed cylinder 1 connected to the hydraulic braking circuit, a pair of opposed movable pistons 5, 8 sealed in the cylinder 1 and a device inserted between the pistons, 5, 8 for taking-up of play due to wearing of the brake shoe linings. The device includes an expansible bush 12 inserted in a seat of the first piston 5 so as to be longitudinally slidable therein a...