PURPOSE:To improve the durability of a bearing, by arranging a sprocket at the front side of a differential between the axles to approach to the bearing which supports the front end of an input shaft. CONSTITUTION:Of a differential unit 51 between axles, a sprocket 58, and a converter 61, in this transfer device, the sprocket 58 is positioned at the foremost position. In other words, the sprocket ...

PURPOSE:To make it possible to prevent a damage of a transmission owing to an over-revolution condition, by producing an alarm and making the clutch in a released condition when the clutch output shaft revolutions are at a specific revolution frequency or more in the in-gear condition of a manual transmission. CONSTITUTION:An in-gear sensor 1 detects that a shift lever 9a is at a specific shift po...

PURPOSE:To accurately detect a driver's intention to change the speed so as to prevent the deterioration in operability by driving a throttle valve to close and releasing a clutch when detected that a shift lever is in shifting. CONSTITUTION:When judged that a manual speed change gear 9 is in neutral position by an in-gear sensor 1 in a control circuit 20, it is judged whether or not a shift lever...

PURPOSE:To prevent useless release of a clutch by fastening a clutch if an acceleration pedal is in the not stepped condition when the maintenance of the neutral condition is detected after detecting that a shift lever is in the shifting condition. CONSTITUTION:In a control circuit 20, when detected that the neutral condition is maintained by an in-gear sensor 1 after detecting that a shift lever ...

PURPOSE:To enable to secure excellent operability at the time of shift down by controlling the opening degree of a throttle valve and the fastening condition of a clutch on the basis of the work position of an acceleration pedal when the shift down is detected. CONSTITUTION:In a control circuit 20, the shift up and the shift down of a speed change gear 9 is detected by comparing the input side rev...

PURPOSE:To enable to obtain the desired jerk value even if the friction coefficient of a clutch changes by compensating the build-up rate of clutch pressure memorized at every speed change stage so that the actual value of a jerk value may accord with the target value. CONSTITUTION:In a controller 30, the car speed is operated by means of a signal from a rotation sensor 20. And accelerations at th...

PURPOSE:To enable the shift-down at a slope during a turning run, by providing a means which can change a preset, running-state-region limited by a limiting means, based on both a vehicle-speed-detecting-means and either one of a vehicle speed and the rate of change in the vehicle speed. CONSTITUTION:A speed change control means C controls the speed change of an automatic gear B to a preset change...

In an electric furnace for producing ordinary steels, alloy and others by arc heat of electrodes incorporated with gas blowing from a furnace bottom into dissolving and refining, plugs having fine pipe holes as gas blowing means are positioned in space each other in the furnace bottom for blowing the gas from beginning of refining to tapping in amount of 1 to 40 N/min per one pipe hole, 20 to 800 ...

The appts. to catch and sever continuous filaments, in winding, using one ring with axially projecting teeth each with an inner sides extending radially inwards to form a common mantle surface, and a clamping ring to act with the inner sides of the teeth, the outer dia. of the clamping ring equals the dia. of the mantle surface formed by the inner sides of the teeth. The mfg. tolerances are select...

The yarn to be transferred is fed at high speed through a traverse mechanism and between a drive roll and a bobbin mounted on a first chuck and rotated by the drive roll to cross-wind a yarn package. An empty bobbin is mounted on a second chuck parallel to the first chuck. When the package is substantially full wound, the empty bobbin is engaged with the drive roll and the yarn package is retracte...

The material comprises an abrasion-resistant pervious nonwoven web of bonded filaments, and an absorbent layer of microfibres. The layers are bonded intermittently with the bonds penetrating through the pervious layer and joining the fibres of that layer to those in the absorbent layer. - The absorbent layer pref. incorporates absorbent particles and/or fibres and is pref. od 30% polypropylene fib...

PURPOSE:To prepare the highly caking title composition containing only small amount of harmful substances, by heating a mixture of a by-product of phenol synthesis through hydroperoxide, or a resinous material obtained by treating the by-product with formaldehyde, and fine powder of coal. CONSTITUTION:A composition composed of (A) 90-40wt% of a liquid obtained by heating tar or pitch which is a by...

There is disclosed a mechanical type of device, effective to suitably spread apart the new tread rings to be applied on the carcasses of worn tires, in the retreading process thereof. The device comprises, substantially, a base (1), bearing a horizontally extending shaft (3) effective to rotate about the axis thereof and at one end thereof there is keyed a bevel gear wheel (5). The latter meshes...

The essential constituents of the composite element are known and available thin-walled hollow glass beads having a diameter of from 2 to 5 mm and a binder which is used in the form of a solution of a light-fast, elastomeric, water-insoluble polymer based on an unreactive polyurethane, the polymer being resistant to UV rays and warming to 150 DEG C, which is mixed with relatively volatile solvents...

Device for adjusting a relative rotational position of a gearwheel and a ring gear which are coaxially mounted, comprising a device for applying a spring force to at least one of the gear wheel and the ring gear so as to form a positive connection between the gear wheel and ring gear, and an hydraulic system for reducing the applied spring force, the hydraulic system being formed of components dis...

PCT No. PCT/SE87/00266 Sec. 371 Date Apr. 22, 1991 Sec. 102(e) Date Apr. 22, 1991 PCT Filed May 29, 1987 PCT Pub. No. WO87/07348 PCT Pub. Date Dec. 3, 1987.A differential gear has a housing which is rotatably driven and which contains the shafts of differential planet wheels for rotation with the housing. The planet wheels are freely rotatable per se and are associated with meshing side wheels rot...