PURPOSE:To enable the inspection of a pinhole in a container concurrently with a reduction in production equipment and energy by extruding a melted hollow synthetic resin from a die of a extrusion molding machine and pressing the synthetic resin from both sides with a die to form into a flat container by a pressure sealing of its outer periphery part. CONSTITUTION:A hollow synthetic resin 2 melted...

PURPOSE:To improve turning performance of a vehicle by engaging the first or second hydraulic clutch by a pressure of oil generated by a difference between delivery amounts of the first/second oil hydraulic pumps connected to the first/second output shafts respectively, so as to distribute more torque by a turning outer wheel. CONSTITUTION:In a power transmitting device for a vehicle providing an ...

PURPOSE:To prevent generation of self-excited vibration in a high differential region by setting target differential limit torque by a characteristic of rising in accordance with a rise of right/left drive wheel speed difference, in a region with a right/left drive wheel speed difference detection value to the prescribed value, and by a characteristic of reversely decreasing, in a region exceeding...

PURPOSE:To provide a sure fail safe function by calculating a controlling lateral acceleration value based on a sensor signal, when lateral acceleration sensor voltage is less than a change quantity limiter value, and restricted by a change to the change quantity limiter value, when the voltage is the change quantity limiter value or more. CONSTITUTION:A differential limit torque giving means (a) ...

PURPOSE:To prevent vehicle behavior from its rapid change in a limited turning region by applying a filter process containing limiting and reducing a torque rise to acceleration sensing target torque, and setting target differential limit torque, so that a turning outer wheel slip amount is prevented from exceeding a turn outer wheel permissible slip amount. CONSTITUTION:A differential limit torqu...

PURPOSE:To improve turnability at the time of tight corner turn running by setting differential limit torque as the target differential limit torque, when a front/rear wheel rotational speed difference and a, right/left drive wheel speed difference are in a prescribed value or more, and setting the target differential limit torque to zero except when the speed differences are in the prescribed val...

PURPOSE:To provide a good acceleration feeling at the time of acceleration on a right/left split #X road by limiting reducing differential limit torque to obtain target differential limit torque, when the differential limit torque corresponding to a right/left drive wheel speed difference is in a reducing side at the time of accelerating a vehicle. CONSTITUTION:A differential limit torque giving m...

PURPOSE:To provide a constitution wherein a brake can be applied to a machine body with no exclusive use brake equipped, when temporarily stopped by operating a continuously variable transmission in a neutral position. CONSTITUTION:A transmitting system in an output side of a continuously variable transmission 1 is branched parallelly into two systems, to provide, in each of these two branched tra...

PURPOSE:To stably end traction control without prolonging unnecessary control at the time of operating an accelerator pedal released, in a control device for traction control of an automatic transmission-mounting vehicle. CONSTITUTION:In the case of opening an accelerator pedal 41 at the time of executing traction control, when a shift up speed change of an automatic transmission 6 is not detected...

PURPOSE:To obtain glass having a hardened film, having stain-proof property and scratch resistance. CONSTITUTION:A protective layer is formed on one face or both faces of glass and a mixture composition consisting of three components is applied thereon in a thickness of 1-15mum. This composition consists of a component A; an alkyl fluoroacrylate, a component B; an acrylic monomer component incompa...

PURPOSE:To make steam high in both temperature and pressure so as to improve the thermal efficiency of a combined cycle electric power plant. CONSTITUTION:A gas turbine plant GT and a steam turbine plant ST are combined, and a supercharged boiler 4 and an exhaust heat recovery boiler HRSG are provided. The turbine of the steam turbine plant ST is divided into a turbine high pressure part 10, a tur...

A portable, umbrella-type shelter including a sheet that can be easily stretched to a framework that includes rods removably attached to one end of a jointed post that has a pointed lower end and a weight that slides against a flange on the lower part of the post to drive the pointed end into the ground. The sheet has loops to be hooked over projections near the outer ends of the rods.

This disclosure relates to polyisocyanate-based foams, particularly to polyurethane or polyurethane-polyisocyanurate foam prepared in the presence of a certain blowing agent. The blowing agent, based on total amounts of a) and b), consists of: (a) from about 5 to about 80 mole percent of a C5-6 alicyclic alkane or mixtures of such; and (b) from about 95 to about 20 mole percent of a mixture of iso...

A method is provided for forming an apex filler including extruding a substantially linear elastomeric strip having a base and a pair of sidewalls converging from the base to an apex. The sidewalls of the elastomeric strip are then engaged with a nip presented by a pair of opposed frusto-conical rollers and a base support. The rollers are rotated to work the elastomeric strip whereby the base of t...

Certain polyether-based or polyester-based polyurethaneureas in solutions of organic solvent at a 12 to 20% concentration are particularly suited for use in a mandrel-dipping process for producing thin-walled elastic articles, such as surgical gloves, which are more resistant to puncture and tear than conventional surgical gloves made from rubber latex.

Blends of branched poly(ethylene terephthalate) ("PET") polymer and recycled plastics can be foamed to produce closed cell structures with advantageous densities, cell sizes, cell size distributions, mechanical properties and thermal properties.

Flame-retardant poly (polyisocyanate-organic phosphorus) products are produced by mixing and reacting an organic phosphorus containing compound and a polyisocyanate compound in the presence of a polyisocyante catalyst. No other blowing agent is necessary. The flame-retardant polyurethane foam products may be used for thermal and sound-insulation, for cushioning, for molding useful objects and as a...

The use of a liquid for the preparation of a rigid polyurethane and/or polyisocyanurate foam by reacting a polyisocyanate and a polyol in the presence of a blowing agent characterised in that the liquid is an inert, insoluble, non-blowing liquid. CFC-free foams may be obtained showing good insulating properties.

PURPOSE:To obtain a simulated display of animation images meeting demand combustion indices at a large capacity with high-speed changeover by repetitively displaying still images in the changeover period of the still images corresponding to the human ability of vision according to the demand combustion indices. CONSTITUTION:The video images previously recorded with an actual furnace are digitalize...

Protective barrier consisting of at least two ballastable elements (3,4) adapted to surround at least partially the work to be protected (1). The height of the individual elements is greater than the water depth. The elements comprise a connection device permitting the structural continuity of the elements after assembly. The protective barrier is entirely independent of the work to be protected. ...