PURPOSE: To perform the measurement of high quality, for quantifying the spectral energy with the low cost, by installing a detector and a luminescent organ on a common base, protecting the same from humidity by sealing, shielding the light, and calculating the set of the multiple measured values by the linear transformation of the weighted integral value. CONSTITUTION: A group of luminescent orga...

PURPOSE:To provide a neuron model element which generates an electric vibration signal. CONSTITUTION:A lipid-impregnated membrane 13 is installed in an logic aqueous solution 12, an ion channel whose selectivity is opposite to that of the lipid- impregnated membrane 13 is buried and installed in the lipid-impregnated membrane 13, an electrode 16 which transmits the membrane potential of the lipid-...

PURPOSE:To estimate a road traffic status in response to an actual drive state by applying fuzzy deduction to the road traffic status based on a drive time ratio and a mean speed of vehicles. CONSTITUTION:A processor of a controller 15 mounted on a vehicle receives a vehicle speed signal, a steering wheel angle signal and a throttle opening signal from a vehicle velocity sensor 26, a steering whee...

PURPOSE:To enhance the charge/discharge cycle lifetime characteristics by furnishing a plurality of longitudinally parallel ribs on both surfaces of a sack- shaped separator in back-to-back arrangement, and forming the ribs on the rear surface in contact with a negative electrode plate with a height which is greater than that of the ribs on the front surface. CONSTITUTION:A negative electrode plat...

PURPOSE:To enhance the welding strength of tabs of electrode plates and a strap to each other by installing a plurality of electrode plates, each having a tab, belonging to the same polarity group in a single row arrangement, and moving a gas burner over the tabs in the direction in which the plates are arranged and also in the direction perpendicular thereto. CONSTITUTION:Positive electrode tabs ...

PURPOSE:To prevent contacting of a positive and a negative electrode plate due to its (their) curving and also slipping-off of the active material from electrode plate by eliminating corrosive elongation of a lattice for electrode plate when the battery is in service, and thereby precluding the center of electrode plate from curving in bow in such a way as protruding. CONSTITUTION:A lattice for el...

PURPOSE:To achieve an effect similar to warm-up operation by detecting the temperature of an internal-combustion engine and setting a power generation mode forcibly when the detected temperature is lower than a predetermined level thereby operating squirrel-cage polyphase induction machine as a generator and applying a load to the internal-combustion engine. CONSTITUTION:An internal-combustion eng...

A gas turbine power plant having a pressurized fluidized bed combustor and an external topping combustor. A cylindrical duct and a toroidal duct direct the flow of hot gas from the topping combustor and distribute it around the circumference of the turbine inlet. The walls of the duct are cooled by water or steam. The walls are formed by tubes, having cooling fluid passages formed therein, that ex...

PURPOSE: To detect a foreign substance by projecting an image of a sample onto the light (dark) background for the foreign substance to be detected, darker (lighter) than the test sample, without specially performing the matching of the background to the sample. CONSTITUTION: A string F as a test sample, is illuminated by the front and rear illuminating means 5, 6, and the image of the string F is...

The invention relates to a polypropylene film comprising one layer. It comprises polypropylene and resin. The resin has a mean molecular weight of >/= 1,500. The invention also relates to a process for the production of film and to the use of the film.

PURPOSE:To prevent the deterioration phenomenon of the superconductive property effectively by making into a structure to prevent to expose the oxide superconductive layer in the atmosphere, as well as making the structure strong to a distortion such as a bending and a compression, generating hardly the deterioration of the superconductive property, so as to give an excellent mechanical stability,...

PURPOSE:To suppress the combining loss of a wire when it is used in the AC current, by insulating a superconducting-element wire by an organic insulating membrane or a sulfide membrane. CONSTITUTION:The surface of a single core or a multicore superconducting element wire is insulated by an organic insulating membrane or a sulfide membrane. The single core or multicore superconducting element wires...

PURPOSE:To prevent a phenomenon that remaining air is expanded to expand the metal-made pipe locally when powder is charged in a metal-made pipe to be heat-treated after working into a fine wire. CONSTITUTION:In a vacuum sealing method for powder 3 wherein the powder 3 is charged in a metal-made pipe 1 and then the inside of the metal-made pipe 1 is made vacuum, the powder 3 is charged in a bottom...

PURPOSE:To efficiently provide a superconducting wire without causing breakage by inserting the given number composite materials, wherein copper is arranged in the periphery of a superconducting member, in a copper sheath to perform cross section reducing working on the composite materials sequentially to form a copper film. CONSTITUTION:Sb is inserted in a Cu matrix containing Nb as a filament, a...

PURPOSE:To provide a polycrystalline thin film excellent in crystal orientation, high-speed film the polycrystalline thin film excellent in this crystal orientation, and provide an oxide superconducting conductor having an oxide superconducting layer excellent in crystal orientation. CONSTITUTION:In a method wherein a particle generated from the target 12 of yttrium-stabilizied zirconium(YSZ) is d...

PURPOSE:To provide a manufacturing method for oxide superconducting wire raw material capable of obtaining an oxide superconducting wire excellent in a superconducting characteristics such as critical current density. CONSTITUTION:A metallic pipe 1 filled with the powder of an oxide superconductor is wire-drawing-treated to a cross section area 20-1.3 times a standard area, the cross section area ...

Articoli a parete sottile, in particolare film a foglia comprendente almeno un primo strato di materiale polimerico includente amido e almeno un secondo strato di materiale idrofobico, caratterizzato dal fatto che detto secondo strato comprende una cera naturale o sintetico o una miscela di cere.; Thin-walled articles, particularly sheets of film including at least one first layer of polymeric mat...

For the detachable fixing of a brake cable assembly (4) to an internal shoe brake for automotive vehicles, one end (18) of the brake cable assembly (4) and the end (17) of a bushing (2) of the brake are coupled by means of a retaining clip (10). The retaining clip (10) consists of an elastic C-section sleeve which envelopes the ends (17, 18) of the bushing (2) and of the brake cable assembly (4) a...

The invention relates to a magneto-optical read head. A magneto-optical head comprises an optically active part which is a very thin magnetic film (32) which rotates the plane of polarisation of the light as a function of its magnetic polarisation, which is itself linked to the magnetic polarisation of the magnetic tape (20) which carries the information to be read and which passes in front of the...

Producing a polymeric material based on ethylene vinyl acetate (EVA) with a density, d, of 0.5-1.3, comprises using an EVA powder crosslinked with peroxide, having a deg. of crosslinking of less than 85% and hot pressing the powder at a temp. T, of 70-150 deg.C. and a pressure, p. of 5-80 bars (5 x 10 power (5) to 8 x 10 power (6)Pa) for a time, t, of 0.5-5 minutes, the values of p, t and T being ...