PURPOSE:To aim at improvements in operability and workability, by installing a clutch lock device which maintains the main clutch once turned off by on- operation of an operating switch in the neutral position of a gearshift lever in a state of being left intact. CONSTITUTION:An operating switch 6 is installed in the holding part of a gearshift lever 3 operating a shift transmission gear 2 of a tr...

PURPOSE:To prevent the deformation of an electrode plate and the filling irregularity of paste by spraying slurry on one face or both faces of a sheet plate made of lead alloy and providing holes penetrating the sheet plate in the succeeding process. CONSTITUTION:A starch material is used as a binding agent when the slurry 1 to be sprayed is kneaded with water to maintain the active material struc...

PURPOSE:To prevent unintended driving of a motor, by setting an accelerator opening voltage during ON state of a brake switch as an offset voltage during full closure of accelerator. CONSTITUTION:When a brake switch 12 is turned ON, an accelerator voltage representing an accelerator opening is read in. The accelerator voltage at this time is set as an offset voltage and stored into a storage secti...

PURPOSE:To prevent an unpleasant steering wheel shock at the time of a brake start on a split road, by braking drive wheels at the time of a slip occurrence on the basis of the quantity of slip in drive wheels on both sides. CONSTITUTION:The 1st drive wheel speed means 11 detecting one drive wheel speed VFR, the 2nd drive wheel speed detecting means 12 detecting the other drive wheel speed VFL and...

PURPOSE:To lighten a driver's burden in traveling at the time of a traffic snarl and garaging by making speed controllable from a predetermined car-speed to stop by only braking operation with the constitution where a car speed is controlled according to the pushing-down quantity of a brake pedal when a slow-speed traveling mode is set. CONSTITUTION:When a slow-speed traveling mode is set, a throt...

PURPOSE:To permit the selection between the free and locked states of a center differential gear device, besides the selection between the two-wheel drive/four- wheel drive and high speed/low speed by arranging the hubs installed onto the output shaft, intermediate shaft, and a front wheel side input shaft of a high speed/low speed transmission mechanism, in series, and by arranging a selecting sl...

PURPOSE:To perform tuning of control content or input information corresponding to fluctuation of a drive system by determining control information or correction value thereof stored in a control memory based on a tuning information. CONSTITUTION:When an optimal control information or correction value thereof is determined from a plurality of control information correcting values set in a control ...

In an automatic transmission, a governor shaft (8a) is arranged so that a center axis (Og) of said governor shaft is interposed between a center axis (Oa) of an idler shaft (9) and a center axis (Of) of a final drive gear (5). In one embodiment, the center axis of the governor shaft (8a) is further disposed between a center axis of an output gear (3) and the center axis of the final drive gear, an...

PURPOSE:To prevent surface stripping, water leaks, etc., due to the effects of chlorine contained in a hot city water from occurring in an application such as for a hose or packing of a solar water heater by using a butyl rubber, chlorinated butyl rubber, or brominated butyl rubber compd. CONSTITUTION:A butyl rubber, chlorinated butyl rubber, or brominnated butyl rubber compd. is used as a hypochl...

A machine including a feeding group or station, a first rotative cutting or creasing station, a second rotative cutting or creasing station and a rotative stripping station characterized by a single drive motor driving the various rotating tools of the stations and a feed roll of the feeding station. Each of the first and second stations and the stripping station have a frame with two lateral fram...

PURPOSE:To prevent a film from stretching or a delay in film supply from occurring by a method wherein output torque of a torque motor does not exceed rotation torque of a shaft, a rotation of an output shaft of the toque motor is set in a reverse direction of the rotation of the shaft and the output torque of the torque motor is reduced as the shaft speed rises. CONSTITUTION:When a shaft 10 rotat...

PURPOSE:To obtain the subject pigment having excellent mechanical durability, etc., and high safety comparable to inorganic pigment and useful for make-up cosmetic, image printing ink, etc., by applying silicon dioxide film containing an organic colorant to the surface of powder particles. CONSTITUTION:The objective pigment can be produced, e.g. by adding silicon dioxide to a cold aqueous solution...

A polymer attenuation filter (16) in a CT machine is mounted at its center and allowed to expand freely at its ends to prevent cracking of the filter as it expands with temperature and after it becomes brittle with x-ray exposure. Vertical expansion of the filter at its center is accommodated by a stress relief hole (30) cut between the center fastening points (24,28). Relatively greater horizonta...

PURPOSE:To prevent the tight corner braking phenomenon, by generating a slip on one of front/rear driving shafts, while making a turn at a low speed, so as to dissolve the difference in rotation speed between the front/rear driving shafts. CONSTITUTION:While making a sharp turn at a low speed, a clutch is easy to slip because the thrust force of a positive clutch cam 5 in a case 1 is small and the...

A system and method for controlling a rotation of drive wheels (15,16) for a vehicle are disclosed in which a slippage (slip rate in percentage) between the drive wheels and a road surface on which the vehicle runs is calculated on the basis of a drive wheel rotation speed and a vehicle body speed, a plurality of different predetermined slippages, each representing a magnitude of a slip occurrence...

PURPOSE:To reduce the size in the axial direction and the radial direction by closely sticking a retainer to the wall section of a casing at the contact face of a cylindrical end face and using the inner diameter section of a centering shaft section as a seal member or a bearing member. CONSTITUTION:A cylindrical retainer 60 is closely stuck to the fitting face 74 of the wall section 51 of a casin...

1. Functional seating furniture, in particular for office use, comprising a frame (1), a seat (2) pivotable about a horizontal frame axis against the force of at least one spring and of adjustable inclination, and also a backrest (3) pivotable in dependence on the respective inclination of the seat, characterized in that the front part of the seat (2) is supported, in particular in the side region...

A pneumatic tire having improved high-speed running performance is manufactured by conducting vulcanization of a green tire (10) in a mold (12) provided at a position corresponding to a given position between the shoulder portion (33) and the bead portion (16) with at least one protrusion (34) which protrudes inside the mold and continuously extends in the circumferential direction of the mold and...

This invention relates to a method and apparatus for displacing a continuous flat sheet (1) of material having a first edge (3) and a second edge (4), running along a first plane in a first direction which is the direction of its centreline to a parallel but sideways displaced direction in a second plane the direction being parallel to the first, in which the second edge (4) of the sheet (1) is di...

A feed table unit of a sheet-fed printing machine with machine side frames for feeding sheets of paper from a stacker to a printing unit includes a feed table including a table top, two side parts holding the table top, a conveyor having a drive for revolving the conveyor about the table top, and deflection rollers supported in the side parts for guiding the conveyor, the feed table being supporte...