Method for purifying a liquid from solid and liquid impurities by flotation-filtration in which the dirt flocks in the liquid to be purified are separated from the liquid to be purified after which they are led to the top of the liquid to form a sludge bed 16 from there to continue out to a sludge canal 17 and to a drain. The purified liquid flows further through a sand filter 18 to an isolated sp...

PURPOSE:To enable high speed operation by aligning a separator supplied to a first adsorption roller and a plate supplied from a conveyance unit to almost the same location in the position corresponding to the separator folding section and the front end of the plate and inserting them by a first and second adsorption rollers. CONSTITUTION:A separator (a) is sent to the lower part of a first adsorp...

PURPOSE:To enable a plate group to be effectively formed, by synchronizing the vertical movement of a lift base with the horizontal movement of the claw parts of a supporting part from the side board of a guide frame, and heaping the plates in sequence on the claw parts from upward to downward. CONSTITUTION:At the time when conveyance by means of a conveyor 1 is stopped by the rear board 7a of a g...

PURPOSE:To enable correct centering to be carried out without damaging a plate, by constituting a position-correcting structure with a pair of eccentric rolls and a position-correcting belt which is streched between said rolls and moves toward the direction and at the velocity respectively identical to those of a conveyor belt. CONSTITUTION:With regard to two pairs of respective two rolls 5a, 5b a...

PURPOSE:To present an electrode plate group for eliminating unwelding of a part of a lug an electrode plate even if width of a connecting shelf is formed into a dimension as same as width of a lug of an electrode plate. CONSTITUTION:Electrode plates respectively having a notch part B, for example, a notch formed into a shape such as C, inverted C, J, inverted J, L and inverted L in a part of the t...

PURPOSE:To improve discharge performance remarkably by adding a specified quantity of silica powder having a specified particle diameter, in which silica fine powders are aggregated to form a secondary and a tertiary particles, in the positive electrode active material. CONSTITUTION:A positive electrode plate obtained by adding 0.2-5wt.% of silica powder having a diameter at 1-300mum, in which sil...

PURPOSE:To reduce the generation of gear noise during shift operation and the occurrence of seizure of a synchronizer ring and to improve durability of gear transmission device by keeping a clutch disengaging state without engaging a hydraulic clutch once in the middle of shift. CONSTITUTION:The hydraulic circuit of a working vehicle, such as an agricultural tractor, is provided with first and sec...

PCT No. PCT/SE84/00356 Sec. 371 Date Jun. 23, 1986 Sec. 102(e) Date Jun. 23, 1986 PCT Filed Oct. 24, 1984 PCT Pub. No. WO86/02530 PCT Pub. Date May 9, 1986.The present invention relates to an incontinence diaper built up from a barrier layer (1) and a nonwoven layer (2) affixed thereto for providing two portions (6, 7) surrounding the lower part of the body and a crotch portion (8) connecting thes...

PURPOSE:To improve visibility by constituting the phase difference plate of the laminate of a phase difference plate formed by using a uniaxial oriented film of a resin having negative double refractiveness and a visual angle compensation plate formed by using a biaxial oriented film of a resin having positive double refractiveness. CONSTITUTION:This phase difference plate is constituted by lamina...

PURPOSE:To improve visibility by constituting the phase difference plate of laminated body of a phase difference plate formed by using a uniaxially stretched film of a resin having positive double refractiveness and a visual angle compensation plate formed by using a biaxially stretched film of a resin having negative double refractiveness. CONSTITUTION:This phase difference plate is constituted b...

PURPOSE:To obtain the polarizer which is small in size and can be used over the wavelength region over a wide range by building the specific laminated polarizer into a fiber and polishing away a part of the fiber near to a core and forming a metallic film on the polished surface thereof. CONSTITUTION:The laminated polarizer 15 is inserted into a spacing part 14. The groove side side surface of a b...

PURPOSE:To minimize the influence of disturbance and to stabilize characteristics as well as to reduce the size over the entire part by connecting an optical fiber having the double refractions different from the double refractions of optical fibers having double refractions to both ends or one end of these optical fibers. CONSTITUTION:The optical fibers having loss wavelength characteristics are ...

PURPOSE:To end and stop work precisely by calculating the proposed number of times of reciprocation on an automatically formed travelling course, and when a service car travels more than a prescribed distance under non-detecting status after passing the calculated number of times, stopping the service car forcibly. CONSTITUTION:An unmanned traveling service car V such as a lawn mower is provided w...

PURPOSE:To prevent assuredly the runaway of a work truck due to a malfunction by stopping the travelling of the truck when both travelled distance and turning angle exceed the set value respectively or the distance of shift exceeds the prescribed value. CONSTITUTION:The 1st controller 13 operates a speed change gear 18 and an electromagnetic brake 19 to stop the travelling of an unmanned work truc...

PURPOSE:To manufacture a device for prolonging a lifetime by making a binder for a light emitting layer and a dielectric layer of transparent ceramics to enable the heating processing, and providing cover parts made of glass in small opening parts to seal the inside. CONSTITUTION:The material, which is obtained by dissolving dielectric element such as BaTiO3 or the like in the Si-(OH)n solvent, is...

A shrimp processing apparatus comprising a washing device (7) for washing loose shrimp material away from edible meat includes a peeler equipment (1) and a wash water recirculation system consisting of a water collecting tray (14) positioned beneath the peeler equipment, a return flume (16), a filter (17) with a reservoir (23) positioned therebeneath and a pressure pump (12) to be fed either from ...

A gradiomanometer 1 measures the difference in pressure between points 3 and 4 to indicate density and hence proportions of two phases (e.g. liquid and gas), each of known density flowing as indicated by arrow 6. A venturi meter 2 measures the difference in pressure between points 4 and 5 to indicate flow rate, initially assumed to be that of the heavier phase only. An iterative calculation makes ...

The present invention relates to a method of manufacturing a fiber-reinforced plastics material. In this method, a foam of a binding agent containing powdery thermoplastic matrix is applied onto a reinforcing fiber web which is then dried, heated and pressed.

A package of a food or a similar product which has to be preserved in fresh state. The package contains a sack (25) charged with a freshness keeping agent for keeping the product fresh together with the product. The package comprises a carrier seat provided in the package and carrying the sack of freshness keeping agent fixed thereto, the seat having one end integrally heat-welded in one of the he...

An electroconductive thermoplastic resin molded product having neither fluffing of electroconductive fibers therein nor jutting phenomenon of electroconductive fibers at the corner parts thereof is provided, which product comprises an electroconductive thermoplastic resin sheet comprising a thermoplastic resin film; a non-woven fabric or a knitted or woven fabric consisting of hot-melt-adhesive fi...