PURPOSE:To prevent the rush of a vehicle caused by erroneous recognition of a stepping pedal in a vehicle having a traction control device by carrying out a braking operation or the throttling of engine output at the time of detecting an accelerator pedal which is stepped in with above a defined stepping force. CONSTITUTION:As the spin of a wheel is detected based on the detected value of a wheel ...

PURPOSE:To make the extent of torque at the time of starting larger and a slip area at the time of reacceleration smaller, respectively, by connecting a turning shaft of a centrifugal governor to each side of input and output shafts of an automatic continuously variable transmission via a one-way clutch, and rotating it with either of the speedier side. CONSTITUTION:A centrifugal governor 9, regul...

PURPOSE:To make an output shaft freely controllable by adjusting the extent of magnetic force in a hydraulic transmission with a hydraulic fluid. CONSTITUTION:When magnetic force is removed in advance at the time of no load in an accelerator, no matter how engine speed may go up, torque transmission is little so that brake force will get off with a small one. And, when the accelerator is suddenly ...

A high pressure steam sterilized plastic container holding an infusion solution therein is prepared first by providing a flexible container made of plastic material and holding an infusion solution. The container is then sterilized in a saturated steam atmosphere which is pressurized by a gas inert to the infusion solution and does not contain oxygen. The infusion solution in the container is not ...

A heelholder for a safety ski binding having a baseplate, a slide mounted for movement between forward and rearward positions, a soleholder pivotally mounted on the slide for movement between closed and open position, a locking device mounted on the soleholder for movement between an obstructed position where it holds the soleholder in the closed position and an unobstructed position, a locking le...

La présente invention concerne une butée avant pour la fixation d'une chaussure sur un ski comprenant un support fixé au ski et sur lequel est montée mobile une mâchoire de retenue de l'avant de la chaussure, des moyens élastiques pour maintenir normalement la mâchoire sur son support dans une position d'enclenchement centrale, et des moyens de liaison entre la mâchoire et son support.

Ce...

PURPOSE:To reduce the size of a waveguide by coating a superconduction thin film to the inner face of a basic pipe, and providing a means holding the temperature of the thin film below the transposition temperature of the superconduction substance at the outside of the pipe. CONSTITUTION:The good conductor thin film 3 on the basic pipe 2 made of aluminum or copper is formed by applying sputtering ...

PURPOSE:To obtain a lightweight oxide type superconductor having superior stability and a specified compsn. consisting of Li, Ti and O. CONSTITUTION:This oxide type superconductor is represented by a general formula Li1+xTi2-xO4 (-0.4<=x<0.5) and is produced as follows: a powdery mixture prepd. by blending a lithium salt which is converted into lithium oxide by heating or lithium-titanium double o...

PURPOSE:To obtain superconductive ceramics mixed on the level of atoms. and having a uniform compsn. and uniform characteristics at high temp. by dissolving prescribed amts. of starting materials such as metal oxides in an acidic soln., uniformly mixing them, evaporating the water and subjecting the resulting metallic salt mixture to calcining, grinding, molding and sintering. CONSTITUTION:Powders...

PURPOSE:To obtain the titled stable superconductive ceramics having a higher critical temp. than the temp. of liq. nitrogen by molding and sintering prescribed amts. of powdery starting materials for Y, Ba, Cu and Mo. CONSTITUTION:Starting materials for Y, Ba, Cu and Mo, e.g., Y2O3, BaCO3, CuO and MoO3 are weighed by prescribed amts. so as to obtain a desired compsn. and they are ground and mixed ...

PURPOSE:To obtain the titled stable superconductive ceramics having a higher critical temp. than the temp. of liq. nitrogen by molding and sintering prescribed amts. of powdery starting materials for Y, Ba, Cu and Hf. CONSTITUTION:Starting materials for Y, Ba, Cu and Hf, e.g., Y2O3, BaCO3, CuO and HfO2 are weighed by prescribed amts. so as to obtain a desired compsn. For example, they are weighed ...

PURPOSE:To obtain calcined powder having uniform and satisfactory superconductivity by putting powdery starting materials in a heat resistant reaction tube, rotating the tube, feeding atmospheric gas into the tube and calcining the starting materials so that the starting materials react well with the atmospheric gas. CONSTITUTION:A tubular heater 4 is placed around a heat resistant reaction tube 5...

PURPOSE:To obtain the title compound material having appropriate porosity, high mechanical strength, heat resistance, chemical resistance, and abrasion resistance by press-molding a specified carbonaceous raw material consisting of short fiber-shaped carbon fiber and pitch, and carbonizing the molded body. CONSTITUTION:A raw material for carbon material consisting of 60-90wt.% short fiber-shaped c...

PURPOSE:To generate a signal at the time of manual opening of braking and prevent any misoperation from occurring by installing a switch between two manual released screws of a magnetic brake. CONSTITUTION:An operating plate 17 is stretched across between two manual release screws 13 of a magnetic brake. In an interval between a cover 15 and the plate 17, an A contact microswitch 19 is provided fo...

PURPOSE:To make the whole body of a braking device compact by installing a rubber elastic member over the whole area of an end face of a piston, and its part extended to the outside of a peripheral edge of the piston is tightly attached to a wall part in and around the piston in an oiltight manner. CONSTITUTION:A peripheral edge of an elastic member 27 to be extended to the outside of the peripher...

PURPOSE:To manufacture resin sealed semiconductor devices without a chip attachment process by using a lead frame modified in the structure, and providing a vacuum sucking hole in the wire bonding machine to directly suck and fix a semiconductor chip. CONSTITUTION:In a predetermined position of a heater block 5 where a semiconductor chip 3 is to be mounted, a vacuum sucking hole 6 smaller than the...

A hydrodynamic brake has a rotor blade wheel and a stator blade wheel with oblique blades and which together form a toroidal work chamber. A series of quick blades are mounted on the stator blade wheel for controlling the flow of braking fluid between the blade wheels and thereby the degree of braking action. Each of said blades is mounted for rotation around a radial axis and can be swung uniform...

This screen-point for carrying out water tests by injection into the ground consists of a tube comprising : a central screen 21 defined by two end sections of substantially equal diameter between which a cylindrical section of limited diameter, pierced with injection holes, is interposed; downstream of the screen 21, a cylindrical driving point ending in the shape of a cone, of smaller diameter th...

Matériau composite comportant une matrice 1 constituée d'une polyoléfine homopolymère ou copolymère semi-cristallin, de masse moléculaire quelconque, un renforcement 2, constitué de matériaux textiles y compris métalliques, revêtu d'une couche d'adhérisation 3 comportant au moins un composant élastomérique et intimement lié à la matrice polyoléfinique 1 par l'intermédiaire d'un enrobage 5, de f...

Device for indicating the tension between a member 1 such as a probe, a tool or an instrument and a linkage element 7 such as a cable. This device is in particular characterised in that it comprises a traction body 26 integral with the element 7, a guide tube 35 placed around the traction body and integral with the member 1 and interacting in translation with the traction body 26 between a first p...