PURPOSE:To facilitate the stall state detection of a control program, by detecting that the control does not return from each routine constituting the control program for a specific time or longer. CONSTITUTION:If a stall state caused by a hardware fault, error of a control microprogram, etc., occurs in some routine among an instruction execution part 11, input/output processing part 12, and input...

PURPOSE:To display strictly a fault and reconstitute a system adequately through software, by generating a fault interruption address, in a central controller fitted with an interrupting function, according to the contents of a counting circuit for the frequency of fault occurrence. CONSTITUTION:Data outputted from a main storage part MEM is checked at any time by a PTYCHK and when it is normal, t...

PURPOSE:To allow an easy manipulation by providing the upper brackets to the seat sliders on the bottom of the seat cushon which are connected to the lower brackets on the floor, and by further providing a connecting member between the upper brackets. CONSTITUTION:The seat slider 9 is attached to both sides of the cushon frame 6c of the seat cushon 6, and the upper bracket 8 is fixedly attached to...

PURPOSE:To improve rigidity and to prevent the titled seat from deforming, by a method wherein a striker is made into a cantilever, a horizontal surface is made into a tapered state and a connecting part of a lock is made into a circular state. CONSTITUTION:A striker 40 is made of an L-shaped comparatively thick steel plate, its vertical surface is made into a fixing part 41 to a car body A, its h...

PURPOSE:To make connection reliable by improving rigidity and preventing deformation, by providing a connecting part, a touching part and a protruding part on a horizontal surface of a L-shaped striker. CONSTITUTION:A striker 40 is formed of comparatively thick steel in about a L-shaped state, whose vertical surface is made into a fixing part 41, and a bridgeform protrusion part 44 to be connected...

PURPOSE:To enable to use the titled rearmost seat for taking a rest as well when a back door is opened, by making a seat back of the rearmost seat into dual structure. CONSTITUTION:The rearmost seat 7 consists of a first and a second seat backs 10 and 11 to be connected with a seat cushion 8 through a reclining device 9. The first seat back 10 is locked to an arm 13 through a lock component 24 nor...

PURPOSE:To obtain the FRP filament of excellent strength which does not cause cutting of a filament during manufacturing and does not contain air bubble etc. in resin, by bunching thermosetting resin impregnated fibers of continuous length and forming them through the die to which ultrasonic vibration is given, then heat curing in a mold. CONSTITUTION:E.g. after plural fibers of continuous leng...

PURPOSE:To emulate varying input data on real-time basis, by equipping the address input part of a storage device with a counter, and combining an address of a CPU and the output of a counter together into an address of the storage device. CONSTITUTION:An RAM1 is stored previously with data using an address generated by combining the high-order digit address 2' and low-order digit address 22. A fi...

PURPOSE:To prevent the production of roughness of an electrode mirror surface due to heat treatment by isolating a reflection mirror surface from an electrode. CONSTITUTION:A disc mirror surface region 7c at the center of a ring-formed junction region 7b contacts P-InP layer 5 via an insulation layer 6. When a drive current flows into the electrode 8 from its ring-formed junction region 7b, an act...

PURPOSE:To automate restarting, by ANDing the output of a circuit which differentiates the alarm output of a watch dog timer with the output of a manual processor starting circuit, and starting the processor. CONSTITUTION:If a trigger pulse to the timer 2 is ceased, the output of the timer 2 turns off a specific time later and an alarm signal is outputted to a terminal 6. At this time, the differe...

PURPOSE:In the electric blower having the motor fitted with the air guide, the fan, and the fan-case in succession, a seal-ring part decreasing the gap between the airguide is fitted on the lower seat part of the fan, and the draft of the lubricating oil on the bearing part is prevented.

PURPOSE:In an electric blower (e.g. one for use in vacuum cleaner) comprising a motor, air guide, fan, and a fan casing, to prevent safely and easily the reduction in efficiency of the electric blower safely and easily the reduction in efficiency of the electric blower which would be caused by the reduction in the amount of intake air.

PURPOSE:To simplify fixing of vanes to an end plate of fan impeller and eliminate generation of running noise without sacrificing the fan performance, by immersing the impeller with many vanes mechanically fitted to its end plate in a resin solution while turning.

PURPOSE:To obtain easily the titled optical fibers having a low loss, by joining a semicircular glass rod obtained by grinding one side of a base material for single mode optical fibers to a rod, containing a core, and having a high coefficient of thermal expansion and one ground side, and drawing the joined glass rod. CONSTITUTION:One side of a base material of circular cross section doped with b...

PURPOSE:To improve external appearance and terminal treating capability by extruding and molding a brilliant film to the surface of the base section of the weather strip while extending a sealing lip being elastically in contact with a window glass in the automobile door waist weather strip. CONSTITUTION:Numerals 20b, 26b are each extended to the base sections of several waist outer and inner weat...

This method relates to the indicator of an escape direction in a building in which a refuge is reached. The method consists in producing an indicator which consists of an underlayer part of an essentially elongated flat shape and of a multiplicity of indicator unit parts which are arranged at a distance from one another in the longitudinal direction on the underlayer part, each of the indicator un...

PURPOSE:To make it possible to carry out easily the joining, by forming protruding ridges or grooves on the outer peripheral surface of an optical fiber by adjusting the internal pressure applied to hole parts in drawing a preform of the side pit type optical fiber having constant polarized waves. CONSTITUTION:A pair of holes (2a) and (2b) are provided in a core part in the long direction in a pro...

PURPOSE:To prepare a large-sized single crystal of InBO3, in a short time, by adding InBO3 to a solvent comprising a mixture of B2O3 and PbO in an amount exceeding the saturation level, heating and melting the mixture, and slowly cooling the molten mixture. CONSTITUTION:InBO3 which is a compound composed of equimolar amounts of B2O3 and In2O3 is added to a solvent composed of B2O3 and PbO in an am...

PURPOSE:To prepare a large-sized single crystal of InBO3, in a short time, by adding InBO3 to a solvent obtained by mixing B2O3, PbO and BaCO3 in an amount above the saturation level, heating and melting the mixture, and slowly cooling the molten mixture. CONSTITUTION:The molten mixture of B2O3, PbO, BaCO3 and In2O3 having a specific composition is filled as a starting raw material 1 in a lidded p...

Undoing or removing thread ends of individually transported textile bobbins which are rotated during the transport about their longitudinal axis and which are blasted with compressed air during the transport from at least one blasting nozzle is effected more efficiently by moving the blasting nozzle in the direction of the longitudinal axis of the textile bobbin or the travel direction of the text...