PURPOSE:To make release of locking easily and rapidly by applying shake in the vicinity of a lock in the range of the second and the third setting time when the object position is not reached within the first setting time. CONSTITUTION:In the operation of change gear actuators 6, 7, for instance, shift in, shift out, select, when shift, select etc. can not be made within the first setting time A, ...

PURPOSE:To prevent shift's overs and shorts from occurring as well as to secure a stable shift position, by setting the desired value with the learning value value made by the detecting value of a stroke sensor in a clutch's on-state in case of setting the shift position of a shift actuator. CONSTITUTION:In both oil chambers 1f and 1g of a stepped cylinder 1a, for example, when hydraulic pressure ...

PURPOSE:To correctly set the neutral position of a shift actuator and the shift position in each speed change stage by performing renewal by using the detection value of a stroke sensor in the operation of a shift actuator to a neutral state, as learned value. CONSTITUTION:The shift quantity of a shift actuator 1 in the operation to a neutral stage is detected by a stroke sensor 4, and the aimed s...

PURPOSE:To permit the smooth automatic speed change operation by installing an electromagnetic opening/closing valve for duty control between a tank and the solenoid valves for driving a shift actuator and a selecting actuator and duty-operating said valve when a gear is set. CONSTITUTION:An electromagnetic opening/closing valve V6 for duty control is installed between a tank T and the solenoid va...

An electronic gear transmission control apparatus commands an optimum gear position based on a shift schedule map according to a vehicle speed and an accelerator opening. When an upshift over two or more gear positions is commanded on the basis of the shift schedule map, a gear shift to the commanded gear position is restrained, and a gear shift to a gear position which is one gear position higher...

PURPOSE:To make safety running attainable without overrunning an engine, by controlling it so as to prohibit the gearshifting within the set time at a time when a decrement rate of car speed is larger than the specified value. CONSTITUTION:An electronic controller 9 connects its output port 9c to a clutch actuator 3, a hydraulic mechanism 4 and a transmission actuator 5. And the input port 9d is c...

PURPOSE:To enable a small-type sealed lead storage battery to be smaller and has a button-like shape by installing pellet-like positive and negative plates composed of a coarsely porous body in a positive and a negative case made of a conductive material respectively, placing the plates facing each other with a separator interposed and joining the cases together with an insulator layer interposed....

PURPOSE:To provide the manufacture of an electrode plate for a sealed lead-acid battery capable of forming a thick active material layer in a short time by electrolytically oxidizing and reducing a lead alloy film or a lead alloy plate. CONSTITUTION:A lead alloy film or a lead alloy plate is electrolytically oxidized to form a positive electrode active material layer on a positive electrode plate ...

PURPOSE:To reduce the production loss and facilitate the moisture adjustment of uniform paste grains. CONSTITUTION:Sludge paste is mixed before 'water kneading' at the ratio of 10wt.% against the weight of the kneaded paste. The electrode plate of a lead-acid battery can be manufactured without impairing the battery performance when the sludge paste is mixed, and the production loss can be sharply...

PURPOSE:To improve cycle life performance by making a specific silica concentration of a gelling electrolytic solution using silica sol where the silica particles are two or more times as long as they are thick. CONSTITUTION:A gelling electrolytic solution is used which has gelled by silica sol using silica particles B instead of silica particles A. The silica particles B are two or more times as ...

PURPOSE:To improve economical advantage and solution retaining property by inserting a separator having extruded parts in one or both sides between a positive and a negative electrodes and filling the gap between the electrodes and their periphery with an inorganic powder. CONSTITUTION:A separator 3 in which extruded parts 4 are formed in one or both sides discontinuously by embossing process is l...

PURPOSE:To raise the temperature of intake air through a throttle in a low pressure pump chamber, and to use it as a pressurized air source for operating an air bubble pump for circulating solar heat hot water by opening a suction valve near the end of a sucking step. CONSTITUTION:Since both a suction hole 20 and an exhaust hole 21 are closed in a sucking step of a piston 24 from its top dead poin...

PURPOSE:To eliminate any interference between an operating lever and a pedal, by making a contact member in an interlocking mechanism so as to come into contact with the operating lever from the clutch-off direction side, in case of such a type of device capable of performing speed shifting and clutch operation with one operating lever alone. CONSTITUTION:In case of a device capable of performing ...

PURPOSE:To prevent oxidation of a working part in an atmosphere created by combustion of a resin layer by irradiating laser light to the working parts butted or superposed with the works provided with a combustible resin layer on at least one surface thereby welding said parts. CONSTITUTION:Works 11, 12 provided with resin layers 13, 14 are respectively butted at the ends thereof and are fixed by ...

PURPOSE:To release shock on speed change by judging the start of speed change based on engine speed or on the variation rate of the speed of rotation of an inputted speed change gear and controlling ignition timing. CONSTITUTION:A controller 16 controls an ignition device based on a signal from a throttle opening sensor 17, signals from shift switches 18, 19, 20, a signal corresponding to the quan...

A continuously variable transmission means for vehicles which enables the engine speed under a high torque to be as small as possible, while ameliorating undesirable noise in a passenger compartment. The transmission means includes a device for detecting a noise and a comparator device for comparing the actual booming noise with a predetermined allowable noise level.

PURPOSE:To improve the cost of fuel and the durability by reducing the closing area of a throttle valve when the stepping amount of an accelerator is below a fixed area, keeping the throttle valve near full opening constantly when in the fixed area, and increasing the engine torque when above the fixed area. CONSTITUTION:A supercharger 6, a speed-change ratio adjusting device 18, a throttle actuat...

PURPOSE:To improve a rate of fuel consumption so sharply, by making a range of closing a throttle valve smaller when an accelerator pedalling extent is less than the setting value, while keeping the throttle valve constant at an approximation to the full open when it goes up beyond the setting value. CONSTITUTION:In this control device, a transmission ratio adjuster 18, a throttle actuator 36 and ...

PURPOSE:To make a sharp improvement in a rate of fuel consumption as well as to secure reliability on an engine, by keeping a throttle valve constant at an approximation to the full open when an accelerator pedalling extent is within the specified range, while increasing the engine torque when it goes up beyond the specified range. CONSTITUTION:In this control device, a supercharger 6, a transmiss...