PURPOSE:To easily allow a slope start by automatically disconnecting a clutch, repeating small advance and recession, and keeping the stop state in appearance. CONSTITUTION:A microcomputer 21 reads the gear position of a transmission 15 by a transmission position sensor 26. In addition, a car speed sensor 26 reads the advance or recession of a vehicle and also reads the car speed in the same way. ...

PURPOSE:To make it possible to convert strong wind arising around a multi- story building into electric energy by making a wind-hole section at a specific height through a multi-story building, and disposing a plurality of wind power generators at the wind-hole section and peripheral corner positions. CONSTITUTION:A wind-hole 2 is made at a specific height through a multi-story building, and a plu...

PURPOSE:To restore the fuel gas pressure to a normal level without stopping the operation of a gas turbine or releasing to the atmosphere from a vent stack, by increasing or decreasing the fuel consumption of each gas turbine until the deviation in gas pressure between the fuel and a reference is zeroed. CONSTITUTION:A load control apparatus for combined power generation facilities composed of 12 ...

PURPOSE:To improve the recovery efficiency of energy by increasing eddy circulation with eddy draft in an air duct through a disc driven by the rotation of a wind mill and with solar heat on the wall of the air duct to collect circulated eddy draft as rotating power. CONSTITUTION:By the rotation of a wind mill 18 exposed to wind, a disc 34 which is installed in an air duct 10 is rotated and driven...

PURPOSE:To surely designate the desired slice position by a simple operation and to reconstitute this designated tomographic image by executing an input operation of a cursor position, when the tomographic image is reconstituted and displayed on a screen, based on projection data collected by a helical scan. CONSTITUTION:To a main computer circuit 4, a function as a tomographic image selecting mea...

An automatic fire detection system characterized by an extremely low incidence of false alarms utilizes two detection channels, one fed by an infrared (IR) detector and the other by an ultraviolet (UV) detector. Signal processing electronics in each channel produce a normalized output signal proportional to the power of incident IR and UV radiation within specific bandwidths. The system features a...

Long-term lubrication of highly loaded lubricating areas or surfaces, such as in very high speed medical and/or dental equipment, is obtained by applying a synthetic film, for example composed of poly(fluoroacrylic acid methyl ester) onto the sliding/moving surfaces, along with a polar oil having high lubricity. Anti-microbial agents can be added to the synthetic film. A pre-coat of molybdenum sul...

Disclosed is a process for fabricating a composite polycrystalline diamond or cubic boron nitride (CBN) compact. Briefly, the process is conducted by mating a pre-formed sintered polycrystalline diamond or CBN compact and a plastically deformable support, and subjecting the mated composite compact to elevated temperature and pressure conditions sufficient to plastically deform the support into att...

PCT No. PCT/FR83/00030 Sec. 371 Date Sep. 15, 1983 Sec. 102(e) Date Sep. 15, 1983 PCT Filed Feb. 15, 1983.An electrolyte for a lead acid accumulator containing 5 to 30 g per liter of pyrophosphoric acid and 5 to 50 g per liter of orthophosphoric acid, the total quantity of phosphoric acid in the electrolyte being less than or equal to 60 g per liter.

PURPOSE:To relieve a feeling of deceleration at clutch desengagement, by putting an engine throttle back in a closed direction in advance of the clutch disengagement which means the starting of shifting operation in time of shifting up and then causing a clutch to be disengaged after making excess torque smaller. CONSTITUTION:When a processor 9a judges that shift is up on the basis of each signal ...

PURPOSE:To enable fine switching operations to be performed and also braking forces to be transmitted to four wheels exactly by a method in which an intermittent operation device permitting switching of two-wheel drive and four- wheel drive is provided, and when a running brake is operated, a switcher is always switched to four-wheel drive. CONSTITUTION:Front wheels 3 and rear wheels 4 are provide...

PURPOSE:To prevent a paper from the injury caused by a ratchet at the delay of the board-taking work by bringing down board-taking guides automatically when papers accumulated on a board-taking board is increased over a fixed amount during the work of board-taking. CONSTITUTION:After printing, a paper 15 bitten by a ratchet 16 of a paper- discharge chain 12 is tranferred above a paper-accumulation...

A method and device for fine profiling or shaping tools coated with super-hard material, for example cubic crystalline boron nitride or diamond, especially tools coated with a single layer and having a prescribed or predetermined profile or shape. The rotatably driven tool is profiled or shaped in the region of the cutting surface by a clustered electron or laser beam which is controlled in a cour...

PURPOSE:To omit deburring and to simplify a post treatment by forming the mouthpiece main body of the mouthpiece consisting of a mouthpiece main body and sleeve by welding a split part and providing a welding burr storing space at the joining part of each split part. CONSTITUTION:A mouthpiece main body 1 is made of a mild steel, composed of the 1st split part 1A consisting of the joint part 10 con...

The compressed gas, before entering the splicing chamber, receives a metered quantity of a suspension which contains a substance improving the textile properties and cohesion of the fibres, the mutual adhesion of the fibres and the strength of the yarn and preventing the fibres from sticking together and a substance having a lubricating and corrosion-preventing effect on machine parts. Such a susp...

PURPOSE:To enable a vehicle to be smoothly started, by interruptedly supplying a brake force holding signal for a prescribed period when the holding of brake force is released, in the case of the method holding the brake force by the action of a brake force holding actuator. CONSTITUTION:Inputting a brake signal 102 and a car speed signal 104 or the like to a hold condition decision circuit 10, if...

PURPOSE:To make it possible to surely eliminate the yarn-hooking step for each undrawn package so that the pruductivity may be enhanced, by forming a spliced yarn therein with slight entangled sections and heat stretched sections in combination. CONSTITUTION:Yarns Y1, Y2 to be spliced together are set respectively on pins 11a, 11a' of yarn gripping receivers 11, 11' and are gripped by press-rods 1...

PURPOSE:To easily fix an outer terminal with a container and connect the terminal to a current collector by bringing a strip of a U-shaped terminal into contact with one end of a current collector and fixing it in a concavity of an opening in a part of a container and welding them. CONSTITUTION:Epoxy resin is filled around one end 12 of a current collector arranged in an opening 9 of a container 1...

The bobbin feeding system of the automatic winder comprises a bobbin feedback line from the automatic winder which is branched off into a residual-yarn bobbin conveyor line and an empty-bobbin conveyor line, each conveyor line being joined with each other and connected to the empty-bobbin discharge line, and a bobbin stripper for removing residual yarn from the bobbin which is mounted on the resid...

2099672 9211246 PCTABS00014 A novel benzodiazepine derivative represented by general formula (I), a pharmaceutically acceptable salt thereof, a pharmaceutical composition thereof, and a process for producing the same. In formula (I), R1 represents optionally substituted aryl, five-membered monocyclic group, six-membered monocyclic group or aromatic heterocyclic group comprising five-membered and s...