PURPOSE:To improve the specific dynamic property by supporting an upper rail at two points by a pair of tolling members for preventing deflection of the rail to an eccentric load on the seat side. CONSTITUTION:A load applied to an upper rail 20 from a seat cushion SC is received by a pair of rotary rollers 30A, 30B, and a tensile strength applied to the upper rail 20 is received by a slider provid...

PURPOSE:To elevate a position of a buckle device, improve opera-bility and prevent the buckle device from interference with a reclining dial when a seat back is sprung up. CONSTITUTION:The rear side wall of a seat cushion 8 supports a reclining device 15 about the support shaft Y on the front side and supports the lower end of an arm 12 of a buckle device 11 about the support shaft on the rear sid...

PURPOSE:To secure the accelerability of a vehicle after escaping from a hydroplane state a checking the overestimation of an accelerating slip with this hydroplane state by installing a hydroplane recovery control means which outputs a control command, controlling the accelerating slip of driving wheels, to an accelerating slip control means. CONSTITUTION:When escaping from a hydroplane state, a c...

PURPOSE:To provide an artificial stone lightweight and excellent in mechanical strength and also to contrive utilization of industrial waste by molding the mixture of fine aggregate incorporating lightweight aggregate and fine powder of fiber reinforced plastic, cement and water and thereafter performing underwater curing and high-temperature curing. CONSTITUTION:Cement is mixed with fine aggregat...

PURPOSE:To safely and readily obtain a carbonaceous inorganic oxide composite excellent in mechanical strength and uniformity with good reproducibility by mixing an inorganic oxide having a porous structure with a phenolic resin and then heat-treating the resultant mixture. CONSTITUTION:A carbonaceous inorganic oxide composite is obtained by mixing an inorganic oxide having a porous structure with...

PURPOSE:To improve the crack prevention, warpage prevention, water repellency and strength of a cured hydraulic substance by curing the hydraulic substance, while spraying steam having a temperature lower than room temperature during the prescribed curing of the hydraulic substance for the supply of insufficient water. CONSTITUTION:A hydraulic substance (A) such as mortar is cured, while a tempera...

PURPOSE:To provide a novel diamond compound suitably usable as an electric charge transport material for photosensitizers or electroluminescence elements. CONSTITUTION:A compound of formula I [Ar1 and Ar2 are each (substituted) alkyl, (substituted)aralkyl, (substituted)aryl, (substituted)biphenyl or (substituted) heterocyclic group; R1-R5 are each H, alkyl, alkoxy or halogen; X is O, S or formula ...

PURPOSE:To control an olefin polymerization reaction so as to continuously provide a polymer having desired quality without lowering production efficiency when polymerization conditions are changed, by polymerizing an olefin by controlling pressure and composition, while controlling feed amount of a monomer, comonomer and molecular weight controller. CONSTITUTION:A hydrogen gas feed line 2, olefin...

A continuous process for deasphalting and demetallating a residue from crude oil distillation, by means of dimethyl carbonate as extraction solvent, comprises: mixing a residue from crude oil distillation with a recycled liquid stream containing oil and dimethyl carbonate, in order to produce a homogeneous solution; cooling said homogeneous solution and separating a refined light, liquid, phase;...

PURPOSE:To provide a hot-dip metal coating bath immersion member which can be prevented from causing the winding up of an alloy layer on the surface of the member and also the sticking of foreign matter even when immersed in a hot-dip metal coating bath and also is free from peeling of film, etc., and has superior thermal shock resistance. CONSTITUTION:The hot-dip metal coating bath immersion memb...

PURPOSE:To suppress the deceleration of a vehicle in a high vehicle speed region and to stabilize the vehicle in a low speed region, by constructing a device so as to output control commands to provide an engine output nearly maintaining the present speed to an engine output control means, when hydroplaning is detected. CONSTITUTION:In a device carrying out a countermeasure control for hydroplanin...

PURPOSE:To improve the safety and reliability of a rear-end collision prevention system by comparing ideal deceleration acceleration with actual one based on the oil pressure of oil brakes upon deceleration to determine whether or not the brakes work well. CONSTITUTION:A oil pressure sensor 18 measures oil pressure, an actual deceleration acceleration alphad is calculated from a wheel speed obtain...

PURPOSE:To prevent air, which flows in through the suction side of the impeller and blown toward its periphery, from colliding at the periphery with air flowing in through the periphery, suppress the increase of the noise of the air caused by the blower, and keep the performance of the blower unimpaired even in the case where an outdoor apparatus is installed without leaving an adequate space betw...

16 METHOD FOR TREATING AGGREGATE MATERIALS AND FOR CONSTRUCTING SKID-RESISTANT ROAD SURFACES Stone chippings of the type used in the manufacture of road surfaces by hotmix and surface dressing techniques, are rendered water resistant, and less susceptible to binder adhesion failure, by treatment with wax, preferably with wax emulsion.

0665p(FF) Lu and Nelson Case 1 AQUEOUS MINERAL DISPERSIONS A process for making vermiculite lamellae that includes delamination of vermiculite ore to produce a dispersion containing vermiculite particles in which an aqueous slurry of unexpanded vermiculite ore, that is untreated by heat or delaminating chemicals, is subjected to a shearing action until a dispersion of vermiculite lamellae having d...

The present invention discloses a portable waste-treatment system. The waste-treatment system comprises anaerobic holding tanks for the anaerobic digestion of waste, and aerobic marches (20, 34 and 42) for the aerobic digestion of waste. The waste-treatment system has a relatively small volume of about 1,000 to 2,000 liters for each person using the marsh. Aerobic digestion in the marshes is promo...

A method for producing synthetic shaped articles simulating marble, granite or the like is provided by the present invention. A thermosetting resin is subjected to first reaction conditions effective to partially polymerize the resin to form a semi-solid mass. The partially polymerized semi-solid mass of resin is comminuted to form a plurality of discrete partially polymerized resin particles. An ...

A leadfree plate-shaped roof flashing material comprises a sandwich structure in which a stress damping and stabilizing layer (1) of ductile material is completely covered on one side and at least partly covered on the other side by preferably metallic foil sheetings (2, 3), e.g. of aluminium foil, designed with densely positioned flattened folded sections (4) having such a form, e.g. as closed in...

An information display system has a display screen which is substantially transparent to a selected band of wavelengths of light and can be mounted on a window. A projector projects an image of light of the wavelengths to which the display screen responds onto the screen to reflect or transmit the selected wavelengths of light from the screen. The screen is formed as a holographic optical element ...

The invention is a treatment for increasing the bone mass or preventing bone loss in an individual afflicted with a bone disease which includes administering to the individual a morphogen in a therapeutically effective amount so as to maintain or stimulate bone formation.