PURPOSE:To provide a gas turbine composite power generation which can change generated output according to the fluctuation of the demand of electric power as a gas turbine is continuously operated, and moreover can be economically operated. CONSTITUTION:When the demand of electric power is large, steam generated in an exhaust heat recovery boiler 02 is fed to a steam turbine through a pressure hea...

PURPOSE:To reduce the shift shock and prevent any adverse effect to auto exhaust gas from occurring by delaying the ignition timing of an engine at a time when a car is in gear shifting during the travel at both economy and power modes respectively, and reducing this timing delay value relatively at the time of shift of the power mode. CONSTITUTION:An automatic transmission 10 is composed of a tor...

PURPOSE:To suppress variation of whole of connection torque even when a friction coefficient of a clutch sliding part is varied. CONSTITUTION:An electromagnet 67 has a yoke 79 whose sectional area is indicated by (a) in a direction perpendicular to magnetic flux. A multiplate pilot clutch 65 has a sectional area divided into sliding parts (b) and (c). An armature 73 is operated for fastening the p...

PURPOSE:To facilitate molding of a part to be detected for detecting the number of revolutions and to improve mounting ability of a sensor arranged in correspondence to a part to be detected. CONSTITUTION:A power transmission device for an automatic transmission is formed such that a first gear shifting mechanism A arranged on an input shaft 11 and operated such that a power transmission route is ...

PURPOSE:To effectively prevent the occurrence of the damage and wear of the important part of a transmission device by primarily blocking entrance of water from the outside by means of a waterproof cap and positive drainage of water which enters once, in a transmission system having a floating type toothed belt pulley. CONSTITUTION:Disc-shaped waterproof caps 17 and 18 are arranged to the outside ...

PURPOSE:To prevent drop in power transmission efficiency and shortening of V-belt life by preventing oil from oozing from an oil-retaining bush and adhering to a belt contact surface without using special seal structure. CONSTITUTION:A V-belt 10 is disposed in winding between a drive pulley 8 installed on an output shaft (crank shaft 5) and a driven pulley 8 comprises a fixed face 17 rotatably int...

PURPOSE:To simply construct a mechanism by equally shortening pressure oil supply passages to a hydraulic clutch type running speed change mechanism and a hydraulically-powered clutch and cutting off the clutch even in such a state that the hydraulically-powered clutch is connected to the speed change mechanism when at a preset speed. CONSTITUTION:A speed change selector valve V3 for a hydraulic c...

PURPOSE:To increase the mechanical strength of a connection section by connecting the end sections of two-layer tubes constituted of outer layers made of a high-rigidity material and inner layers made of a thermoplastic resin with a pipe coupling, and fusing the thermoplastic resins of the inner layers butted in the pipe coupling. CONSTITUTION:When two-layer pipes 1, 2 constituted of outer layers ...

PURPOSE:To provide the fusing/connecting method of a pipe coupling generating no step in a pipe and not impairing the outer appearance by molding and processing the generated beads in space sections, not preventing the generation of the beads. CONSTITUTION:The inner periphery 11 of a pipe coupling 1 and the outer periphery 21 of a pipe 2 to be inserted into the inner periphery 11 are heated, then ...

A machine (10) for peeling products such as fruit, tubers and vegetables and for cleaning mussels consists of a container with cylindrical chamber (11) near whose lower base rotates coaxially therewith a motorised processing disc (14). The container (11) exhibits a side passage (16) for unloading of the peeled product. An element with cylindrical wall (17) coaxial with the cylindrical chamber (11)...

A spreading machine has a first conveyor belt, with a high friction rest surface for carrying a grid to be covered with paste; a paste spreading chamber towards which the first conveyor belt advances, where paste is spread on an upper and a lower face of the grid; apparatus for spreading paste on the grid at the spreading chamber; a paste loading hopper which feeds the spreading chamber; a second ...

An electromagnetic valve assembly having upper and lower modules. A standardized lower module can be joined with one of several upper modules having a different axial length for varying the magnetic field strength of a coil arrangement in the upper module without changing the length or position of an armature tube in the lower module.

PURPOSE:To enhance appearance by covering an external wall rising from a horizontal level of a balcony floor, etc., from the rear to the upper end thereof with a waterproofing sheet, and at the same time, mounting a coping so as to cover the upper end part of the waterproofing sheet. CONSTITUTION:An external wall panel 3 is installed, and a frame member 5 is mounted on the panel 3 in horizontal di...

PURPOSE:To provide the guidance system of a self-traveling car in which the appearance of a floor face can not be damaged, the plural number of times of reutilization can be attained, and a low cost can be realized. CONSTITUTION:A guide line 1 is plotted along a prescribed traveling path on a floor face 2 with a luminescent coloring matter material or a material constituted of the luminescent colo...

In a pneumatic vehicle tyre, the rubber inner layer is formed from an adhesive rubber and styrene-butadiene copolymers, wherein the content of styrene, which is bound in the molecule, in the blended mixture is at least 15 parts by weight per hundred parts of rubber. A low gas-permeability and sufficient mechanical strength are hereby attainable for the rubber inner layer. The production of the pne...

Oppfinnelsen angår formlegemer avskummede polylaktider, som kan oppnåsved skumming av en blanding av drivmid-delholdige, amorfe polylaktid-granulaterog findelt polylaktid som ikke innehol-der drivmiddel, samt en fremgangsmåtefor fremstilling av formlegemene.; The invention relates to foamed polylactide articles obtainable by foaming a mixture of amorphous polylactide granules which contain a blowi...

La presente invención se refiere a un método para producir polvo, caracterizado porque comprende: (A) formar una corriente de material fundido que fluye axialmente; (B) formar una corriente de gas anular, divergente, que forma torbellino, alrededor de y a lo largo de la corriente fundida; teniendo esa corriente gaseosa una relación de velocidad angular a velocidad axial suficiente para hacer que a...

PURPOSE:To provide the polycrystalline thin film and oxide superconductor having excellent crystal orientability by depositing constituting particles on a base material while irradiating the film forming surface of a base material with an ion beam at a specific incident angle from a diagonal direction. CONSTITUTION:Many fine crystal grains 20 having the crystal structure of a cubic crystal system ...

The panel is made from a basic mortor containing 1 - 5 per cent of cellulose or polyethylene fibres and 1 - 6 per cent of polyacrylonitrile and polyvinyl alcohol fibres. It is also equipped with lengthwise reinforcing strips (3) of a synthetic material, located in zones which are subjected to stress, e.g. the points (2) on which the panel rests. The reinforcing strip can be, for example, of polypr...

The invention relates to foamed polylactide articles obtainable by foaming a mixture of amorphous polylactide granules which contain a blowing agent and of a finely divided polylactide which does not contain a blowing agent, and to a process for producing same.