PURPOSE:To permit the coasting traveling of a car by the revolution energy of a flywheel by connecting the flywheel with the driving shaft of the car through a transmission and keeping the revolution of the flywheel within a prescribed revolution region by ON/OFF-controlling the driving shaft. CONSTITUTION:A main clutch 2 switches-ON and OFF the transmission of the engine output to a transmission ...

PURPOSE:To reduce the fuel consumption, noise, etc. by reducing the aimed speed change ratio and correcting the revolution speed towards reduction, if the variation of the engine revolution speed is below a prescribed value, when the aimed speed change ratio is determined from the opening degree of a throttle and the revolution speed of the secondary pulley. CONSTITUTION:When a car is in traveling...

PURPOSE:To improve the speed change characteristic by juding the belt slip and increasing the line pressure when the actual speed change ratio is set outside the max. or min. speed change ratio in the mechanism of the transmission speed is set outside the max. transmission speed in the mechanism. CONSTITUTION:The actual speed change ratio (i) is calculated in a calculation part 45 from the outputs...

The instrument has projections with locking teeth for locking the instrument in its closed clamping position, said projections being located near the connecting zone between the levers of the instrument and their ring grips. Near one projection a slide having a wedge surface is provided, which may be shifted between the projections against spring force by pressure onto a key of the slide, for spre...

PURPOSE:The titled molded article useful as magnetic tapes, etc., having high strength, high elasticity and improved dimensional stability, by melting a liquid crystal polyester obtained by copolymerization of an optically active monomer in a specific temperature range, molding it into a sheet, etc., and quenching it. CONSTITUTION:(A) A nematic or smetic liquid crystal polyester is copolymerized w...

A microwave carrier signal is transmitted throughout a surveillance field. Two low frequency signals are also radiated into the field from opposite sides to limit the field size. A miniature receptor-reradiator containing a nonlinear signal mixing device responds to the signals when in the field to return a modulated carrier signal to a receiver device for actuating an alarm. The alarm is actuated...

PURPOSE:To enable positioning of a moving table to be performed high accurately further in a short time, by connecting the moving table with a counterweight through a pair of feed screw threads and a power transmission mechanism. CONSTITUTION:A device, mounting a moving table 11 and a counterweight 12 respectively to feed screw threads 13, 14 threaded in the same direction, connects the screw thre...

PURPOSE:To perform the positioning of a moving table high accurately in a short time, by individually connecting the moving table and a counterweight with forwardly and reversely rotating feed threads constituted on the same axis. CONSTITUTION:Feed threads 13, 14 are provided on the same shaft and threaded in the reverse direction to each other. A device respectively mounts a weight 12 to the thre...

PURPOSE:To enable a device to perform high accurate further high speed positioning of a moving table in a short time, by providing the moving table and a counterweight so as to be moved in a reverse direction by a link mechanism. CONSTITUTION:A device mounts a moving table 11 and a counterweight 12 to upper and bottom nodes of a link mechanism connecting four links 15 into a tetragonal shape by th...

PURPOSE:To high accurately perform positioning of a moving table in a short time, by setting weight of the moving table to be different from that of a counterweight further forming their weight difference larger than the static friction force of a movable part. CONSTITUTION:A moving table 2 of weight W is connected by a belt 4 with a counterweight 3 of weight (W-DELTAW) smaller by weight DELTAW th...

PURPOSE:To offer a manufacturing method for slenderly forming a soldering bump by a method wherein transverse stress generated as the result of heat generation from an integrated circuit is absorbed by the elasticity of the soldering bump. CONSTITUTION:An electrode 2 is formed on an integrated circuit substrate 1 and the part except the electrode 2 is masked by an insulating film 3. Next, a conduc...

A method and an apparatus of forming a multilayer printed circuit board which can positively remove voids in the prepregs in the printed board and enhance the reliability of the produced printed circuit board and is superior in economy, wherein a laminated assembly of a plurality of printed circuit board components and a plurality of prepregs alternately laminated on each other is sandwiched betwe...