PURPOSE:To permit a smooth and simultaneous insertion of the cut edges of a tubular film by inserting a guide plate of a cutting device between a holding roll and an elastic holding roll. CONSTITUTION:When a piston rod is moved down in a cutting cylinder 53, a guide 58 of a guide plate 57 is brought into contact with a tubular film 2' to hold is widthwise. At this time, a cutting edge 59 comes in ...

PURPOSE:To perform the positioning of a gearshift lever in an accurate manner as well as prevent any operational error from occurring, by operating a main clutch for its on or off to the gearshift lever operating a shaft transmission gear for a travel device, while installing an operating switch operating an engaging device of the gearshift lever on and vice versa. CONSTITUTION:An arm 58 is instal...

PURPOSE:To bundle a bag not to permit a product to be loose in the bag by a method wherein a folded portion of a bag is lowered by lowering four holding claws by a specified amount to be moved horizontally between the two upper holding claws and the two lower holding claws and a bundling jig is attached to the folded portion of the bag. CONSTITUTION:While holding devices 10a, 10b of the upper part...

PURPOSE:To prevent short sized articles, small articles and heavy weight articles, etc., from falling off by making a movable belt roll for table on the upstream side and a movable belt roll for table on the downstream side not to interfere with a heater on the lower side. CONSTITUTION:A belt roll 2a, which approaches to the upstream side to a heater H2 on the lower side, and a belt roll 4a, which...

PURPOSE:To prevent short sized articles, small articles and heavy weight articles, etc., from falling off by making a movable belt roll for table on the downstream side separate from a movable belt roll for table on the upstream side when upper and lower heaters are closed. CONSTITUTION:A movable belt roll for table 4a on the downstream side, which approaches to the upstream side to a heater H2 on...

PURPOSE:To enhance the running ability in low and middle speed ranges, and the steering stability and rectilinearly advancing stability in a high speed range by a vehicle speed responsive type mechanism adapted to open and close in accordance with a rotational speed, in a fluid passage communicating between a plurality of fluid chambers and an accumulator chamber. CONSTITUTION:In a differential ge...

PURPOSE:To simplify a control system and to improve reliability, by a method wherein a load thrust control oil pressure and a starting clutch oil pressure having a proportional relation with transmission torque are controlled through a single solenoid valve. CONSTITUTION:During idling before starting, a signal oil pressure P2 of a solenoid valve 302 for controlling load thrust is zero, an output o...

PURPOSE:To set the hydraulic load pressure to a proper value by installing a control valve for Controlling the hydraulic load pressure and a solenoid valve and providing an input port, drain port, output port, main spool, output hydraulic pressure feedback port, subspool, and the first and second springs, for the above-described control valve. CONSTITUTION:A control valve 210 for controlling the h...

PURPOSE:To make a power transmission member settable in parallel with a propeller shaft as well as to simplify its structure ever so easy, by setting up a lock mechanism operating handle for a differential gear of vehicles for wastelant, while connecting this handle to the differential gear via the power transmission member. CONSTITUTION:A differential gear 4 is installed in the point midway in an...

PURPOSE:To avoid getting any influence due to a variation in the promotion of deceleration by an automatic transmission as well as to restrict a backward speed without fail, by controlling an engine speed so as to cause a rotating speed of the control shaft, set up downward from an output shaft of the automatic transmission, to become less than the specified value. CONSTITUTION:In this saddle type...

Normally a first target value is given and a reduction ratio of the continuously variable transmission is adjusted in such a direction as to bring the actual value into agreement with the first target value. However, when a predetermined heavy load condition on an engine is detected, a second target value is immediately given and the reduction ratio of the continuously variable transmission is adj...

PURPOSE:To reduce a distance between both gears and a diameter of supporting bearings to reduce a built-in space by supporting a counter gear and a pinion gear with a first and a second bearings in the position respectively outer than both the gears on a counter shaft. CONSTITUTION:A first and a second bearings 76, 77 are respectively engaged with the outer sides opposite to both a counter gear 56...

PURPOSE:To prevent a film from contracting and improve the sealability by adding a process in which a film is stretched by a contraction preventive roller of which film feeding speed is faster than a heater roller, and a process in which the stretched film is cooled by cooling air, after a sealing process. CONSTITUTION:Since the film feeding speed of a contraction preventive roller 4 is faster tha...

PURPOSE:To improve the responsiveness of skid control for slips which are brought about immediately after a speed change, by setting up a controlled variable immediately after the speed change for a controlled variable obtaining the output of an engine in which the driving torques of driving wheels before and after the speed change become a generally constant value so as to make faster the speed o...

PURPOSE:To prevent the ununiformity of the amount of electrolyte between cells to improve the life of a battery by connecting the lower part of each plate group with a porous body so as to have continuous electrolyte. CONSTITUTION:Porous separators 3 in cell compartments are connected with a porous body 6 arranged in the lower part of each partition 4 so that the plate groups of a sealed lead-acid...

Per il dispositivo per paraffinare di una macchina tessile, che possiede un corpo di paraffina solido, per provvedere di paraffina un filo scorrente su questo, è previsto che il dispositivo per paraffinare, allo scopo di manipolazione più facile e per il miglioramento nell'applicazione di paraffina uniforme sul filo, possieda un'unità compatta, che porta parti sostanziali del dispositivo per paraf...

A method for controlling a continuously variable transmission (6) having a pair of pulleys each of which includes a groove defined between a stationary pulley element (8,14) and a movable pulley element (10,16), including the step of using hydraulic oil for increasing and decreasing the width of the groove to respectively decrease and increase the radius of rotation of a belt (4) looped around the...

A power train control method and system for controlling a power to be transmitting to a traction wheel (3R) of a vehicle from a vehicle engine (1) through an automatic transmission (2) for shifting its speed range according to shift patterns depending upon a speed of vehicle and a load of vehicle engine. When slippage occurring on said traction wheel (3R) is detected, the automatic transmission (2...

A shift control apparatus for an automatic transmission (20) of a motor vehicle, including a sensor (11) for detecting a throttle valve (24) opening which regulates an intake air quantity supplied to the vehicle engine, an engine speed senior (12) for detecting the engine speed, a vehicle speed sensor (13) for detecting the vehicle running speed, a calculating device (15) for calculating the intak...

The present invention relates to a method and to a device for separating blood present in a blood container (1) into components (34, 36, 35) by centrifuging the blood, and for transmitting at least one of three stratified components (34, 35) obtained by centrifugation in sterile fashion to a respective side container (2, 3) connected to the blood container (1) via a respective hose (4, 5). The flu...