The invention relates to a mobile X-ray apparatus with an X-ray tube, which is secured via an arm arrangement on a carriage, which is provided with wheels and can be run along the ground. The X-ray tube is adjustable in the longitudinal direction of the carriage and vertically. In order to obtain a mobile X-ray apparatus in which a rapid and simple positioning of the X-ray tube can be carried out,...

A process for adhering a latex film to a polymeric substrate through the formation of covalent bonds at the interface of the polymeric substrate and the latex film. The covalent bonds are formed through the reaction of a cyclic imino ether group, 2-alkenyl-2-oxazoline, and a coreactive group, active hydrogen, epoxy or anhydride group, one of which is present in the polymeric substrate and the othe...

The transmission system produces a signal relating to the speed of the vehicle, and a signal relating to the amount of operation of an accelerator pedal. A third signal is produced, relating to the load of the vehicle. A control is responsive to the signals for producing a control signal to the actuator to shift the gear-type transmission into a target gear position. The control has a memory fo...

PURPOSE:To increase combustion efficiency by controlling an air inlet damper and a dehumidifying spray nozzle by oxygen concentration difference in combustion gas before and after it passes between plates. CONSTITUTION:Combustion gas produced with a burner 1 is passed between negative plates in a basket 8 with a blower 2, cooled with a dehumidifying spray nozzle 4, dehumidified with a demister 6 t...

PURPOSE:To promote the stabilization of transmitting torque permitting dispersion of an engine speed by suspending integrating correction while clearing an integrator and outputting only a reference signal corresponding to the engine speed in the time of low throttle opening. CONSTITUTION:A starting clutch 20 continuously controls its transmitting capacity by a signal input to a starting control s...

PURPOSE:To promote the prevention of a belt slip and the sureness of a speed change speed by controlling a speed change ratio controlling oil chamber so as to obtain the higher of the speed change oil pressure or minimum oil pressure while increasing a pressure of oil in a load thrust controlling oil chamber when necessary. CONSTITUTION:Two or more control valves 43, 45 respectively control each o...

PURPOSE:To aim at enhancing the power characteristic of a vehicle on a slope and at ensuring the safety on a turning road by changing over a counter speed change gear section so as to compensate differences in gear ratio between speed stages in a main speed change gear section when control is made depending upon an inclined angle and a steering angle. CONSTITUTION:An automatic transmission is disp...

PURPOSE:To promote warm-up of an engine by changing a counter speed change gear section into the low speed side when the warm-up of the engine has not yet been completed, so that the engine rotational speed is automatically held to be higher over whole running mode if the engine is cold. CONSTITUTION:An automatic transmission incorporates a counter speed change section which is in series with a ma...

Engine speed is controlled during gear change by way of both fuel supply apparatus and exhaust brake so that engine speed is equal to the rotational speed of an input shaft of a transmission coupled via a clutch to the engine. When the engine speed is higher than the rotational speed of the transmission input shaft, exhaust braking is performed to quickly reduce the engine speed thereby establishi...

PURPOSE:To prevent the inner distortion depending on the winding position and the aging, by providing specific winding thread length and the end face angle to a polyester fiber package having specific thread orientation, tension fluctuation and average differential weight between the central and end portions. CONSTITUTION:In order to release the inner distortion after winding, the crystal orientat...

PURPOSE:To prevent aging making a package under winding out of contact by means of a spindle drive winder then winding with specific slow traverse and higher than specific speed thereby reducing distortion caused by the winding position of package. CONSTITUTION:The winding speed must be higher than 5,000m/min where 5,500m/min is preferable, to produce a string having such inner structure as the cr...

PURPOSE:To obtain a package which has the improved filament releasing property because of possibility of neither shape deformation nor slip-off of single layer from a bobbin by winding-up a carbon filament in a specific apparent winding-up density onto a bobbin which has an outside diameter of a specific length or above and on which uneveness is formed. CONSTITUTION:The outside diameter of a bobbi...

PURPOSE:To smoothly disengage gears, when a command of disengagement is received, by coincidentally controlling the opening of a throttle valve to a value of opening in the no-load state of an engine. CONSTITUTION:A command of gear disengagement is output to a gear shift actuator, and a delay time is measured to perform measurement of engine speed(Ven). A controller is provided with a memory unit,...

PURPOSE:To certainly cut-off the clutch engagement and brake application in the transmission stop state independently of the viscosity of working oil by adjusting a discharge port which shifts integrally with an operating member into the throttle opening state and controlling the oil pressure so that transmission stop state is generated. CONSTITUTION:A discharge port 31 is formed onto the outer pe...

A hollow filament bundle for use in a separator module is made by rotating two co-axial spiders 24 and 28 and looping a continuous hollow filament which is fed from a package 32 alternately around the arms 26 and 30 of the two spiders. This is done by means of a guide 40 which is reciprocated between the two spiders by a screw threaded shaft 34 which is rotated first in one direction and then the ...

Ethylene glycol is prepared by a process in which ethylene oxide is extracted from an aqueous solution with near-critical or super-critical carbon dioxide. Thereafter an ethylene oxide-carbon dioxide-water mixture is contacted with a catalyst to form ethylene carbonate, which is then hydrolyzed to ethylene glycol in the presence of the same catalyst. The ethylene glycol is separated as product and...

PURPOSE:To prevent assuredly generation of sloughing to be generated at the time of releasing strings by forming a shape of the corn coiled by up to a string supply tube and making its lower part small is diameter and its upper part gradually bigger in diameter. CONSTITUTION:In the string winder, the string (a) is released upward from the string supply tube 2 inserted in a peg 1 to be wound from a...

A lifting mechanism for the pressing roller of the feed mechanism of a crusher for scrap. The rotor of the crusher, via a lifting mechanism that acts upon a mounting bracket of the rotor mounting, can be removed from a split housing after an upper part of the housing has been raised about a horizontal pivot axis and has been secured in position relative to a lower part of the housing, whereby pivo...

A control system for a continuously variable transmission has a line pressure control valve having ports and a spool for controlling the line pressure of oil supplied to a cylinder of a pulley device to change the transmission ratio. The line pressure control valve has chambers. When a motor vehicle is decelerated at coasting of the vehicle, the spool of the line pressure control valve is shifted ...