PURPOSE:To prevent the blasting-up of an engine due to a various sorts of diff by compulsorily maintaining the center diff lock state up to the time when a free wheel clutch is switch to the axle lock state during the transition to the four-wheel drive state from two-wheel drive state. CONSTITUTION:A transfer 5 is equipped with a center differential gear 1, two/ four-wheel selecting mechanism 2, a...

PURPOSE:To prevent the blasting-up of an engine by setting a two-wheel/four- wheel selecting device into the four-wheel drive state and setting a free wheel clutch device into the axle lock state, during the transition from the two-wheel drive state to the four wheel drive state, and by setting the center differential gear to the differential gear free state. CONSTITUTION:When a two-wheel/four-whe...

PURPOSE:To remove various inconveniences which may occur in a differential limiting device when pulling a vehicle, etc. by connecting one side gear of a differential device to a differential case at the same time the connection between said side gear and the mount case of a direction changing mechanism is cut off. CONSTITUTION:A transfer which is connected to a transmission has a center differenti...

PURPOSE:To remove remaining yarn of end yarn, by winding a small amount of yarn around empty bobbins, drawing the bobbins from spindles and raising them a little by an autodoffer, cutting securely suspended yarn which is connected from winding parts of yarn end to yarn winding parts of the bobbins at restarting of spinning frame. CONSTITUTION:The winding yarn end 8 is wound 2-3 times around the wi...

Werkwijze voor het toevoeren van inslaggaren aan de gaap bij een weefmachine, waarbij eenzelfde soort inslaggaren (A, B) vanaf minstens twee voorraadspoelen (3, 5), via respektievelijke draadvoorbereidingsinrichtingen (7, 8) en insertiemiddelen (9) aan de gaap (20) kan worden toegevoerd, daardoor gekenmerkt dat de gemiddelde garenaftreksnelheid waarmee het inslaggaren (A, B) van minstens één van d...

The ski fastening includes a front engagement element (3) and a rear engagement element (2) for a boot; either one of the front or the rear engagement elements has a single activation element (27) for the separate and simultaneous adjustment of both the front and rear engagement elements.

A foam absorber having electromagnetic energy attenuation characteristics comprising an open cell reticulated polyurethane foam impregnated with a conductive ink applied to a surface of the foam substrate. The conductive ink is applied as by spraying to a surface of the foam, coating such surface and gradiently loading the foam with the ink by penetration of the ink in gradually decreasing amount ...

Thermoplastic resin sheets are manufactured by extruding molten thermoplastic resin at an extrusion velocity V through a slit provided in an extrusion mold so as to form thermoplastic resin sheets with embossed surfaces, the thermoplastic resin being extruded from the slit in said extrusion mold under conditions such that the ratio V/H of said extrusion velocity V to the width H of said slit excee...

The present invention is directed to a process for producing a molded part by reacting an organic isocyanate with an active hydrogen group-containing material in the presence of a reinforcing fiber mat in a closed mold via the RIM process. The key to the present invention resides in the use of relatively high viscosity components.

In a Raman cell (10) which is subject to optical distortion of the path of a laser beam (40) by heating of the gas from the Raman conversion process, vibrating blades (50) cause the gas to mix and thus provide thermal homogeneity within the beam path.

Defects in a measurement device are detected in a biochemical analysis apparatus wherein a droplet of liquid sample is applied to an analysis medium containing a reagent, which chemically reacts with a specific constituent in the liquid sample, the analysis medium is then incubated, the optical densities of the analysis medium are determined, and concentration of the specific constituent in the li...

A low voltage monitor and microcontroller output monitoring circuit for insuring proper operation of a microcontroller in a furnace control system. A switch connected to a reset port of the microcontroller is capable of putting either a high or low voltage signal at the reset port. A high signal is required for normal operation of the microcontroller. The low voltage monitor connects to a power su...

An auxiliary direct current electrical power source for protection of a wide variety of DC powered circuits, in particular those of computer systems, upon loss of commercial alternating current (AC) power, to sustain necessary or required functions for the full duration of the ordinary utility company AC power loss. The direct current power source will generally be one or more rechargeable gel cel...

An arrangement for communication between two CPUs (9, 12) which allows diagnosis of whether the cause of an interrupt in communication between the CPUs is due to a routine interrupt or a failure in the communication line. Timers (7:13) generate overflow signals in the event that data from one or the other CPU is late in arriving. Lateness is determined by comparing the timer values to stored value...

PURPOSE: To provide a safety binding tool for Alpine ski for holding the back end of ski shoes on ski plates. CONSTITUTION: This safety binding tool includes a base plate 7 extending through a supporting plate 13 of the sole of shoes and a jaw part 3 for holding the shoes and the base plate 7 is directly supported by a ski plate over at least a part of the length and an elastically deformable mate...

PURPOSE: To turn up a carcass fabric having high rigidity by arranging an expandable annular bladder for turn-up having a front edge to be directed toward a drum side and a pressurizing means at the bladder. CONSTITUTION: Bladders 1, 2 are reinforced by non-stretchable cords 10, 20 placed at 90 degrees. An overall of the wall 21 of a radial outside of the pressing bladder 2 and the wall 11 of the ...

PURPOSE: To facilitate the priming of the print head mechanism of a ink-jet printer and to simplify the print head mechanism. CONSTITUTION: A print head mechanism is formed of a print head 1 and an ink reservoir 4 and mounted on a scanning carriage which moves across a recording medium. Ink drops are injected from the ink channel of the print head 1 during printing. The ink channel is replenished ...

PURPOSE:To obtain an electric current led which can continue to feed an electric current to a superconducting coil, which can prevent an oxide-based superconducting conductor from being damaged and in which creeping heat is small even when a low temperature side lead composed of the oxide-based superconductor is quenched. CONSTITUTION:A bypass circuit which detects an abnormal voltage due to the q...

PURPOSE: To recover from a crash in an electronic reprography system, for which plural jobs are simultaneously turned into an active state. CONSTITUTION: The reprography system monitors the jobs turned to the active state inside the system and monitors the number of times that the system crashes, while a specified job is in the active state. By comparing the number of times that the crash is gener...