A vulcanization method and press in which at time-spaced intervals of 1 to 40 seconds, temperature measurements representing increments of heat supplied to the vulcanizable body are taken of a medium used for vulcanization. A summation of the measurements continuously during the vulcanization process represents the heat supplied to the body and when the summed heat quantity equals the total heat q...

The cylinder body(1) is composed of an inhaling portion, a discharging portion (14), a hollowed space made on the inner surface of a driving space of the inhaling portion edge, a cap(2) and a locking plate(3). This body is attached on the frame. A hollowed hole(41) is made around the piston. A horizontal inserting hole (42) and a vertical discharging hole(43) are established. A stopper (6), which ...

PURPOSE:To decrease shocks generated when torque is varied and the speed of revolution is changed by connecting a clutch negative pressure chamber to a plurality of paths with throttles through solenoid valves. CONSTITUTION:A clutch negative pressure chamber 150 is connected to paths 186-192 with throttles 194-198 through solenoid valves 162-168, and speed which the negative pressure chamber 150 i...

PURPOSE:To enable the surface temperature of a friction plate element to be suppressed from increasing, by switching a speed change shift in accordance with a speed change map changed by a speed change interval. CONSTITUTION:If a timer t1 is in a predetermined value T0 or less, a counter N1 is compared with a predetermined number N0 (step 260). When the counter N1 is in a value not reaching the pr...

PURPOSE:To enable a drop of torque in an output shaft to be decreased, by increasing a stroke speed of a piston and increasing engagement force after a transmission reaches a predetermined operative condition. CONSTITUTION:The pressure of oil, supplied to a pressure oil chamber 6 in the engagement side of a K/D brake 2, is controlled, and while a difference between an input shaft rotary speed N1 a...

PURPOSE:To enable a coast down control to be surely realized, by draining clutch pressure oil and controlling pulley ratio to a side of low speed ratio, while a pulley is raced, when rapid deceleration is performed. CONSTITUTION:When rapid deceleration is performed, a return of pulley ratio to a side of low speed ratio is delayed as compared with a decrease of a car speed, and the situation of no ...

PURPOSE:To enable a belt to be prevented from its noise and heat generation, by controlling oil pressure to the minimum oil pressure, which can hold low speed ratio in an N, P range, and reducing a side pressure applied to the V belt. CONSTITUTION:As a manual valve 70 is actuated, a signal oil pressure P4, acting on a back pressure chamber 58 in a regulator valve 50, is turned off. Consequently, a...

PURPOSE:To enable hunting action, caused by supply and discharge of pressure oil, to be prevented, by placing a shift down control valve in an inoperative condition in a speed change and introducing gentle pressure oil to a pulley control valve. CONSTITUTION:Since the second solenoid valve 92 is turned off when a vehicle is in normal running, a signal oil pressure P2 of a regulator valve 40 is alw...

PURPOSE:To obtain acceleration performance in accordance with the will of a driver, by performing a control in such a manner that the more is the depressing distance of an accelerator, the more the promotive amount of a down shift is increased. CONSTITUTION:If an accelerator is depressed about to its intermediate opening, a down shift cam 68 turns accordingly moving the position of a pin 67 of a d...

PURPOSE:To prevent the occurrence of overflowing at times of injection of dilute sulfuric acid and chemical conversion treatment of a battery jar as well as to make the extent of initial capacity improvable, by assembling a porous separator in compression without doing ordinary aging and drying after filling up a grid with crude paste, while injecting the dilute sulfuric acid in the state that moi...

PURPOSE:To improve the turning performance with the simple constitution when a vehicle turns at a low or middle speed, by torque-controlling the right and left hydraulic clutches so that the torque distribution ratio on the outer wheel side is increased in the low or middle speed region when the vehicle turns. CONSTITUTION:Driving shafts 4R and 5R are connected, permitting transmission, through hy...

PURPOSE:To improve the turning performance with the simple constitution when a vehicle turns at a high speed, by torque-controlling the right and left hydraulic clutches so that the torque distribution ratio on the inner wheel side is increased in the high speed region when the vehicle turns. CONSTITUTION:Driving shafts 4R and 5R are connected, permitting transmission, through hydraulic clutches 4...

This invention relates to a process for treating capsules intended for closing containers provided with a heat-sealing joint, composed of four layers, either a cardboard seal, a wax layer, an aluminium film and a final layer formed from a polymer, characterised in that the abovementioned wax 7 is subjected, before its introduction between the cardboard seal 6 and the aluminium film 8, to a microwa...