A continuous screw centrifuge has a rotating solid-walled drum 5 and a filter 1 which extends generally transversely across the drum to filter the liquid discharging therefrom. The filter may be an annular disc mounted either on the drum or on the differentially-rotating screw 4. Apertures 10 may allow liquid to bypass a clogged filter, and baffles 11, 12 separate the filtrate from the bypass liqu...

PURPOSE:To make a proper shift-up indication attainable all the time, by comparing the setting value, to be made larger as the air density is lower, with the actual value of an engine speed and, when the actual value is larger than the setting value, letting a device perform the shift-up indication. CONSTITUTION:A device bearing the above caption compares the speed detection value by an engine spe...

PURPOSE:To make a proper shift-up indication attainable all the time even in case of being insufficient in engine warming up, by making the setting value in an engine load comparing device the smaller the lower in value the lower in engine temperature. CONSTITUTION:A device bearing the above caption compares the speed detection value by an engine speed detecting device 1 with the speed setting val...

PURPOSE:To make improvements in starting operatability, by making a starting gear step possible to be set to first gear only at a time when a first gear starting signal is inputted, in case of using an automatic transmission which starts a car in a way of selecting an ordinary starting gear step to a shift-gear step of more than second. CONSTITUTION:During engine runnings, at an automatic shift co...

PURPOSE:To prevent a clutch characteristic from being deteriorated as well as to aim at the promotion of longer service life and stabilization, by detecting the temperature-up state value of a magnetic-particle type solenoid clutch and, when the detected value is more than the specified value, compensating a desired engine speed for its increment. CONSTITUTION:A device bearing the above caption co...

This technological process publicizes that the utilization of gas turbine for making the chemical energy, included in the fuel to deliver mechanical energy or electrical energy. In order to drive gas turbine, the compressed air used for combustin fuel should increase its humidity before combustion to replace a portion or entire quantity of heat diluted air contained with water steam. The increasin...

PURPOSE:To make it easy to dispose refuse by removing oil content and water content from it, by dehydrating sludgy waste mainly consisting of metallic powder containing oil and water by a porous board, and by heating it by the heat of exhaust gas. CONSTITUTION:The combustion gas in a combustion chamber 2 is fed into a cyclone 36 in which dust is collected, passing through a forward pipe 39, circul...

Extrudable elastomeric compositions are formed by blending from at least 10 percent, by weight, of an A-B-A' block copolymer where "A" and "A'" are each a thermoplastic endblock which includes a styrenic moiety and where "B" is an elastomeric poly(ethylene-butylene) midblock with up to about 90 per cent, by weight, of at least one polyolefin which, when blended with the A-B-A' block copolymer and ...

Extrudable elastomeric compositions are formed by blending from at least 10 percent, by weight, of an A-B-A' block copolymer where "A" and "A'" are each a thermoplastic endblock which includes a styrenic moiety and where "B" is an elastomeric poly(ethylene-butylene) midblock with up to about 90 per cent, by weight, of at least one polyolefin which, when blended with the A-B-A' block copolymer and ...

PURPOSE:To form the titled insulation type fly-back transformer subject to easy production at low cost with sufficient dielectric strength by a method wherein a low-voltage coil bobbin for low-voltage coil is separately provided to be engaged with a primary coil bobbin. CONSTITUTION:Before a core 5 and a high-voltage bobbin 8 are fixed to a primary coil bobbin 6, a low-voltage coil bobbin 11 is in...

PURPOSE:To provide a thermoplastic polymer compsn. having excellent rigidity, flow characteristics and heat distortion resistance and suitable for use as a material for a molding of an automobile, by blending an amine compd. and a polymer such as polyamide with an ethylene/unsaturated carboxylic acid copolymer. CONSTITUTION:100pts.wt. ethylene/unsaturated carboxylic acid copolymer (A) (e.g. ethyle...

PURPOSE:To form a rubber compsn. having excellent ultra-low-temperature properties and oil resistance, by using a chlorinated silicone rubber obtd. by chlorinating a specified silicone rubber and crosslinking it. CONSTITUTION:A rubber compsn. is formed from a crosslinked chlorinated silicone rubber obtd. by chlorinating a silicone rubber of the formula (wherein R's are the same or different group ...

PURPOSE:To increase a pressure accepting area against a twisting vibration and improve a strength against the vibration by a method wherein at least a part of the mounting portions between a motor base and a main body is inclined. CONSTITUTION:In order to mount a fan motor 3 of an outdoor unit, a cantilever supporting using a motor base 12 is applied. The motor base 12 is vertically installed and ...

PURPOSE:To drive a liquid crystal display device which has high display quality and small power consumption by detecting the temperature of a liquid crystal cell and selecting the frequency of a driving signal suitable to the detected temperature, and then driving the liquid crystal cell. CONSTITUTION:A reference clock signal outputted from an oscillation circuit 1 is inputted to a time counting c...

PURPOSE:To obtain a wiring substrate, to which a wiring is formed with high density, by shaping the wiring substrate by cutting a structure having multilayer wiring structure acquired through a thin-film forming technique. CONSTITUTION:A first wiring layer in which a plurality of fine wirings are extended and shaped in one direction through a lithographic process is formed on the surface of a firs...

PURPOSE:To facilitate operational control, by arranging the aeration pipe connected to an air introducing pipe to a bottom part and providing a plurality of activated sludge beds above the aeration pipe. CONSTITUTION:Sewage is introduced into a flow amount adjusting tank 10 through a raw water introducing pipe 15 and flooded from a flow passage 16 to enter a first sewage treatment tank 11. The sew...