PURPOSE:To always generate a constant creep force by correcting the clutch transmission torque capacity according to the difference between the variation quantity of increase of the number of engine revolution and the specified idle variation quantity and automatically adjusting the creep force. CONSTITUTION:Though, in idling of a power range, a starting clutch 22 is slip-controlled so that the cr...

PURPOSE:To make it possible to automatically adjust the force cf basic creep so as to enable a constant creep force to occur always, by compensating the capacity of transmission torque of a clutch in accordance with the difference between a variation in the rotational speed of an engine and a variation in a regulated idle speed which has been previously set. CONSTITUTION:An input interface 68 whic...

PURPOSE:To enable a starting clutch to be uncoupled quickly at a sudden stop in the device in the caption, by controlling a starting clutch such that the transmitted torque capacity becomes somewhat larger than that of a reverse driving torque when the throttle opening degree is closed completely or near the state thereof, on detecting the complete coupling state of a clutch. CONSTITUTION:A discri...

PURPOSE:To improve fuel consumption of an engine and its output, by stopping the supply of fuel to the engine, when its operative condition satisfies a predetermined condition, and increasing a supply amount of fuel in accordance with selected shift patterns when the predetermined condition is not satisfied. CONSTITUTION:If an operative condition detecting means detects a deceleration condition, a...

PURPOSE:To prevent engine stall due to the erroneous engagement of a starting clutch at the time of reversing a vehicle by maintaining a slipping condition without permitting complete engagement even if relative rotating speed becomes below a set value when said relative rotating speed on the input and output sides of said starting clutch has a tendency to increase. CONSTITUTION:When a vehicle is ...

PURPOSE:To prevent a vehicle from starting springing out, by increasing a transmission torque capacity of a starting clutch from the transmission torque capacity, corresponding to an idle speed, by a time gradient of fixed value or less, when the vehicle, during its stopping, selects its non-running range to running range from an engine high speed condition. CONSTITUTION:A hollow shaft 19 is rotat...

PURPOSE:To obtain a glass article having an excellent antifogging property, durability and surface hardness by laminating a carable acrylic resin film and specific cured film obtd. from PVA, silica and org. silicon compd. on a glass base plate. CONSTITUTION:This glass article is laminated with the following films A, B in this order on the glass base plate: A: The curable acrylic resin film, B: the...

PURPOSE:To make clutch not to be set in engagement even if any failure occurs in an electric power supply by making an electromagnetic valve for starting a normally closed type. CONSTITUTION:An automatic clutch device 4 has four electromagnetic valves 14-17 and a double check valve 18, and electromagnetic valves 14-16 are of a normally closed type and the electromagnetic valve 17 is of a normally ...

PURPOSE:To make possible to increase the size of a side gear as large as possible within a limited space, by supporting a differential gear carrier only to one shaft section of the side gear on the front axle driving side. CONSTITUTION:A differential gear carrier 41 is cantilever-likely supported between a side gear 42 on the front axle driving side and the mount casing 32 of a rear wheel drive ri...

PURPOSE:To make it possible to easily obtain a reduction ratio in accordance with the running condition of a vehicle, by setting the reduction ratio in accordance with the frequency of opening and closing of a throttle valve, the frequency of idle rotational speed and an averages vehicle speed. CONSTITUTION:Date of an averaged vehicle speed, the frequency of opening and closing of a throttle valve...

PURPOSE:To provide a normal operation of a system by a method wherein foreign items flowing from a gas flowing pipe and a liquid flowing pipe into an accumulator are caught by a filter and water content contained in a heat transferring system is adsorbed in a dryer arranged in the liquid flowing pipe. CONSTITUTION:A filter 8a is arranged in a path of a gas flowing pipe 5, and a filter 8b, a dryer ...

PURPOSE:To quicken installation works and reduce the reversal space by taking up a row of electrode palte grups while they are divided into a left and a right groups. CONSTITUTION:An anode terminal column MPP and a cathode terminal column MNP of electrode plate groups B1, B6 are provided at one side of one-end cell chamber 5 and the other end cell chamber among six cell chambers of a battery jar 3...

Process of finish-grinding rings on the outer surface or inner surface, especially for finish-grinding race rings of rolling bearings. A ring to be machined is accommodated by a work fixture with centring via a hydraulic centring means and is driven in a rotating manner by a driver. The ring surface to be machined is measured during a grinding operation. The grinding operation is regulated and/or ...

The invention relates to mammographs which make it possible to obtain a radiograph of the breasts. It consists in connecting the compression cushion (205) of a mammograph to the moving carriage (206) which drives it via a stationary piece (101) and a moving piece (102), which are themselves connected to a system of hinged parallelograms (104, 105). A spring (203) holds these parallelograms substan...

This invention relates to method and apparatus for compressing an assembly of plates inside a valve regulated lead-acid battery thereby allowing the battery case to expand without causing slippage or partial loss of contact between the battery plates.

There are disclosed an automatic gear change control apparatus for an automobile and a method of controlling such apparatus. A rotational output (101) of an internal combustion engine (1) is connected to drive wheels (6) of the automobile and a load device (4). When a gear shifting-up of an automatic transmission (2) is to be effected, the load applied by the load device (4) is increased, or the l...