PURPOSE:To prevent an adverse effect on slip control by performing the rich air-fuel ratio operation for NOX absorbent regeneration during the slip control of a lock-up clutch. CONSTITUTION:This control device for an internal combustion engine with an automatic transmission is provided with an automatic transmission control circuit 35 performing the slip control of the lock-up clutch of an automat...

PURPOSE:To provide a rolled web feeding device, which does not require a breaking device and which can feed a band-like film at a constant speed, in response to increase and decrease of the winding diameter of the rolled web film. CONSTITUTION:A third driving motor 40 is coupled with a rolled web film 15, and the rolled web film 15 is rotated in the predetermined direction so as to feed a band-lik...

PURPOSE:To control boost pressure to arbitrary characteristics by a simple and low-cost configuration by operating a continuously variable transmission which transmits driving force of an engine to an air compressor so that boost pressure reaches a set value which corresponds to a degree of opening of an accelerator. CONSTITUTION:An air compressor 11 which pressurizes suction air and supplies pres...

PURPOSE:To prevent power from consuming wastefully to improve fuel consumption and reduce size and weight by controlling the coil current of an electromagnetic coil to the minimum required current value according to a variation in power voltage and negative pressure by a controller. CONSTITUTION:In a controller 37 which inputs signals from a speed sensor 49 and a discharge pressure sensor 51, an e...

PURPOSE:To provide a continuously variable transmission whose mounting position is not specified, by constituting a continuously variable transmission case into two divisions, conducting the axial suspension of a drive shaft and a driven shaft at this case, making one side of the drive shaft an input shaft and the other side of it a PTO shaft, and supporting the case in the right and left frames o...

PURPOSE:To prevent the shaking of side gear free ends and the partial wear of a washer by conducting centering so that the free ends may carry out support mutually through a. support portion. CONSTITUTION:The device is equipped with a differential case 21 to be driven in rotation by the drive force of an engine; a pair of vehicle wheel side side gears 31, 33 whose axial outside end portions 35, 37...

PURPOSE:To prevent the burning of part of a belt caused by friction heat that is generated between the belt and pulleys and stays in the pulley members, and fusion due to heat. CONSTITUTION:This consists of a pair of pulley members 18, 19 which are in the state of confronting each other in an axial core direction and whose belt hang-winding portion 4 diameters are changeable and whose mutual appro...

PURPOSE:To circulate heating medium by a circulating pump having a small lifting capacity. CONSTITUTION:A bypass pipeline 7 is a tube in which heating medium 2 flows to bypass a heat collector 1. A solenoid three-way valve 8 is provided at a connecting part of a circulating passage 5 to the pipeline 7, and a flow switch 9 for detecting inflow of the medium to a storage tank 2 is provided. The ther...

PURPOSE:To prevent dispersion of specific gravity of an electrolyte by stopping formation before reaching the theoretical quantity of electricity converting an active material into PbO2 in a cathode and stopping again after polarity conversion when activation is conducted to both electrode plates formed by filling water kneaded paste of a lead oxide in each current collector. CONSTITUTION:It is pr...

PURPOSE: To reduce the cost of a collimator apparatus and to improve its functions, by forming an opening which makes x-ray pass from an x-ray source to a detector array body on a location fixed partition for blocking x-ray and mounting a location adjustable collimator ring neighboring to the opening. CONSTITUTION: This collimator apparatus is provided with a location fixed partition 300 made of a...

PURPOSE: To provide a centrifuge bowl and a method for separating whole blood into some components (blood plasma, platelet, and so on) of lower concentrations and the other components (RBC) of higher concentrations, and collecting components of both concentrations without requiring to stop the revolution of the bowl. CONSTITUTION: This centrifuge bowl enables to change the direction of fluid strea...

Keratin fiber condition is evaluated by testing dry hair to determine analysis factors. For each factor, two values of elongation are determined by measuring the force required to obtain a first value and a second value of elongation of the fiber. The percent total elongation of the fiber to its break point is also determined. The ratio of the two measured forces is used with the percent total elo...

A toroidal carcass (1) for road vehicle tires, of the type presenting two annular beads (2, 3) connected by a toroidal reticulated structure (5) defined by tow numbers of loops (6, 7) extending in offset radial planes of the carcass (1) and from the respective beads (2, 3) to the center line of the reticulated structure (5); the loops (6, 7) being formed by winding respective continuous cords (8, ...

Water-atomized iron powder for powder metallurgy having a hardness of particle cross section of from about Hv 80 or higher to about 250 or lower, the iron powder having been atomized with water and dried, and having a particle surface covered with oxides which are reducible in a sintering atmosphere, and which has an oxygen content of 1.0 wt. % or less. The water-atomized ion powder can be made by...

A porous polyurethane tube suitable for use as a vascular graft prosthesis is prepared by placing solvent type polyurethane resin coated mandrel in a static coagulant consisting of water, ethanol and optionally aprotic solvent within 30 seconds immediately after the coating step, separating the tube by placing the mandrel in a swelling agent containing at least 90 percent by weight of ethanol and ...

PCT No. PCT/DK92/00329 Sec. 371 Date May 2, 1994 Sec. 102(e) Date May 2, 1994 PCT Filed Nov. 10, 1992 PCT Pub. No. WO93/09753 PCT Pub. Date May 27, 1993.A container for receiving and separating blood plasma into its ingredients comprises two sealingly coupled sections (1 and 2). One container section (2) and the adjacent portion of the other container section are made of solid material, and the tw...

A method for separating co-mingled polymeric materials, in particular polyethylene terephthalate (PET) and polyvinyl chloride (PVC) is described. The process involves selectively dissolving a supercritical fluid into one of the materials at the appropriate temperature and pressure. Upon rapid reduction of the system pressure, the selected material foams providing a change in density. Under ambient...

Method of detecting and evaluating analog photometric signals in a test carrier analysis system, and apparatus for carrying out the method. The test field of a test carrier is irradiated by a light source clocked in light-dark phases. The reflected light is detected by a measurement receiver over a measurement period having several light-dark phases, and integrated. An effective suppression of str...